Vehicles
10 not categorized PORSCHE 356 A SEAL RUBBCan't find what you need? Try browsing the Accessories or Exploded Diagrams!90011202950 Known as: radial sealing ring 14 x 24 x 7 View/Change Diagram
$21.23
Make a selection 311906102A These days, if we can find a factory fuel injection harness in any condition it is a miracle. The only alternative is to repair your current one. Injector leads and boots make it as easy as soldering and heat shrinking. Available for both d jetronic (mpc) and ljetronic (afc), these boots and leads make an undetectable repair. View/Change Diagram
$11.90
Make a selection 90150504132 If you are restoring an early 911, attention to detail is a top priority. We go out of our way to ensure that our trim parts are finished as closely to original as possible. The ends are properly rounded and finished so that the rubber insert fits seamlessly. This is a high-quality replacement, that we source in Germany to ensure quality, reliability and precise fitment. It includes the rubber gasket and rubber piping. Sold individually. 1 necessary per car. Please note: please check the model fitment tab to ensure accurate fitment. View/Change Diagram
From $321.20
Make a selection 6425 The 6al delivers everything the 6a does with the addition of a built-in soft touch rev control. This feature allows you to set an rpm limit to protect the engine from over-rev damage caused by driveline failure or missed shifts. Other msd rpm controls can be connected to the 6al such as a three step module selector or rpm activated switch . The 6al also comes supplied with rubber shock mounts and 3000, 6000, 7000, 8000, rpm modules. All necessary parts and wiring instructions are included. General Fitment911 1987-89911 1984-86 911 1978-83 930 1975-77 911 1974-77 911 1970-73 911 1965-69 944 1989-91 944 1985-88 944 1982-85 924 1986-88 924 1980-85 924 1976-79 914 1970-76 912 1965-69 911 1989-94
$309.95
Make a selection 916604101BX If your starter is on its way out, you will notice an intermittent clicking noise and a delay in the vehicle starting. Eventually you hear a metallic screeching noise that is a sure sign that your starters bendix mechanism, bearings or solenoid are kaput. When ordering a new starter be sure to check the rubber cap on the terminal for cracks which allows moisture in and it is a good idea to check your starters hardware as well. Features: high quality remanufactured starter from Germany. Armature continuity tested, gauged, straightened and shimmed. All shaft splines and load bearing surfaces lubricated with oe high temp. Materials. Includes highest quality replacement parts, including starter drive components, so...(choose a part on the right to read more) View/Change Diagram
From $446.60
Make a selection 90155901122 If you are restoring an early 911, attention to detail is a top priority. We go out of our way to ensure that our trim parts are finished as closely to original as possible. The ends are properly rounded and finished so that the rubber insert fits seamlessly. This is a high-quality replacement, that we source in Germany to ensure quality, reliability and precise fitment. It includes the rubber gasket and rubber piping, part # 90155910653 sold individually. Right or left side fitment. 2 necessary per car. Please note: please check the model fitment tab to ensure accurate fitment. View/Change Diagram
From $97.90
Make a selection 914201151B These are the felt cushions (pieces of carpet) that the gas tank rests on to cushion it from the car body. Absolutely necessary to keep your gas tank from rubbing squeaking and wearing holes in itself three required General Fitment914 1970-76
$9.50
Make a selection 911641301CXFVD Remanufactured part sourced in Germany. Includes a new rubber sealing ring. Purchase a newly remanufactured unit from us and an additional charge (a core deposit) will be added to the purchase price of the part. After receiving your new part, kindly send back your old part, or core . Once the core is returned to us and it has been inspected to ensure it is rebuild-able and resell-able, the core deposit will be refunded. Sold individually. 1 necessary per car. Please note: this is a special-order item. Special order items are sold on a non-cancelable, non-exchangeable, non-returnable, non-refundable basis. Please call us in advance of placing your order, these are very hard to come by and in some instances, we c...(choose a part on the right to read more)
$1,037.30
Make a selection 911FDLNK Upgrade your stock front swaybar with this simple bolt in replacement for the factory drop links.
$205.00
Make a selection 911604101AX If your starter is on its way out, you will notice an intermittent clicking noise and a delay in the vehicle starting. Eventually you hear a metallic screeching noise that is a sure sign that your starters bendix mechanism, bearings or solenoid are kaput. When ordering a new starter be sure to check the rubber cap on the terminal for cracks which allows moisture in and it is a good idea to check your starters hardware as well. General Fitment911 1974-77930 1975-77 911 1978-83 911 1984-86 911 1987-89 914 1970-76 911 1970-73
From $399.59
Make a selection 964604104X This part is a remanufactured part, as such an additional charge (a core deposit) will be added to the purchase price of the part. After receiving your new part, kindly send back your old part, or core . Once the core is returned to us and it has been inspected to ensure it is rebuild-able and resell-able, the core deposit will be refunded. If your starter is on its way out, you will notice an intermittent clicking noise and a delay in the vehicle actually starting. Eventually you hear a metallic screeching noise that is a sure sign that your starters bendix mechanism, bearings or solenoid are kaput. When ordering a new starter be sure to check the rubber cap on the terminal for cracks which allows moisture in ...(choose a part on the right to read more) General Fitment911 1994-98911 1989-94
From $250.59
Make a selection 93064130201GEB Remanufactured part sourced in Germany. Includes a new rubber sealing ring. Purchase a newly remanufactured unit from us and an additional charge (a core deposit) will be added to the purchase price of the part. After receiving your new part, kindly send back your old part, or core . Once the core is returned to us and it has been inspected to ensure it is rebuild-able and resell-able, the core deposit will be refunded. Sold individually. 1 necessary per car. Please note: this is a special-order item. Special order items are sold on a non-cancelable, non-exchangeable, non-returnable, non-refundable basis. Please call us in advance of placing your order, these are very hard to come by and in some instances, we c...(choose a part on the right to read more)
$2,014.10
Make a selection 919110 Magnecor’s kv85 competition (8.5mm) and r-100 racing (10mm) ignition cables feature magnecor’s exclusive 2.5mm high capacity metallic inductance emi suppressed conductor consisting of stainless steel wire precisely wound at 200 turns per inch over a ferrimagnetic core. The insulating jacket is made entirely of magnecor’s exclusive tc-1500-hs high strength aerospace grade silicone rubber, and its single layer construction will prolong the jacket’s insulating ability by conducting extreme heat away from hot-spots that occur near over-the-limit heat sources. General Fitment911 1984-86911 1987-89
$195.95
Make a selection 919111B Magnecor’s kv85 competition (8.5mm) and r-100 racing (10mm) ignition cables feature magnecor’s exclusive 2.5mm high capacity metallic inductance emi suppressed conductor consisting of stainless steel wire precisely wound at 200 turns per inch over a ferrimagnetic core. The insulating jacket is made entirely of magnecor’s exclusive tc-1500-hs high strength aerospace grade silicone rubber, and its single layer construction will prolong the jacket’s insulating ability by conducting extreme heat away from hot-spots that occur near over-the-limit heat sources. General Fitment911 1984-86
$192.34
Make a selection 996TTHFPPPB The automotive speed technologies 996 tt fresh air intake plenum and hard inlet pipe kit is designed to enhance the performance of your Porsche 996 tt by allowing fresh air to flow freely to the turbos for quick spool and additional power - very important for modified cars running larger than OEM turbos or running high boost. The system consists of the speedtech hi-flow intake plenum with 70mm outlet tubes, attached to 70mm molded hard plastic tubes for uniform high flow. Silicon hose is supplied to connect to the turbo inlets. The speedtech hi-flow plenum is designed to flow more air than the OEM plenum and deliver it quickly and smoothly with no restrictions from the maf tube all the way to the turbo inlets. ...(choose a part on the right to read more) General Fitment911 TURBO/GT2 2001-05
$2,551.50
Make a selection 96437504381 Replace your worn-out, original soft rubber engine mounts with our higher density, rs specification rubber bushing. This is manufactured of rubber with a 75-shore hardness value. 75-shore is the same density as what is used in the rs models. It is more durable, provides more positive, sharper shifts and offers crisper throttle response. Yet, rs spec rubber is still quiet and comfortable for street use. Features: sharper shifts crisper throttle response does not produce nvh (noise vibration harshness) like teflon or solid bushings rubber has a shore hardness value of 75 (like rs models) made in Germany this mount is a high-quality OEM (original equipment manufacturer) replacement part, designed to perform like t...(choose a part on the right to read more)
From $199.99
Make a selection 99350465901 This is the rubber insert for the optional roof spoiler that contains a 3rd brake light at the top of the rear windshield. The option was # m599. This rubber insert seals the 3rd brake light in. Sold individually. 1 needed per car. Please note: we also sell a complete roof spoiler assembly that includes the insert spoiler and third brake light, it is our part # 190044812. View/Change Diagram
From $53.90
Make a selection 919108 Magnecor’s kv85 competition (8.5mm) and r-100 racing (10mm) ignition cables feature magnecor’s exclusive 2.5mm high capacity metallic inductance emi suppressed conductor consisting of stainless steel wire precisely wound at 200 turns per inch over a ferrimagnetic core. The insulating jacket is made entirely of magnecor’s exclusive tc-1500-hs high strength aerospace grade silicone rubber, and its single layer construction will prolong the jacket’s insulating ability by conducting extreme heat away from hot-spots that occur near over-the-limit heat sources. General Fitment911 1974-77930 1975-77 911 1978-83
$331.10
Make a selection F6464120001 Instrument faces are one of the most visible and frequently looked at components in your Porsche. When making the decision to change them you want to make ensure that you select a high quality product similar to your originals. Each of our sets are made in Germany and use the factory scripting (font). Our faces also offer the same uniform night time shading and includes the original die cut notches for easy installation. Each kit is made for global distribution, so simply pick out the faces that match your originals. They are available in a variety of colors to make a bold statement, or to match exterior paint schemes. This kit includes faces for: manual transmission / tiptronic transmission / kph / mph / celsi...(choose a part on the right to read more) General Fitment911 1994-98911 1989-94
From $418.70
Make a selection E13209 Introducing the latest in tow hook innovation: engineered with an increased side load capacity and adjustable-length rigid mount receiver. This tapered stainless loop design incorporates a new locking function to maintain your preferred loop position. Additional features include machined graphics, rotational timing and camera mount compatibility.
$145.00
Make a selection F6464120004 Instrument faces are one of the most visible and frequently looked at components in your Porsche. When making the decision to change them you want to make ensure that you select a high quality product similar to your originals. Each of our sets are made in Germany and use the factory scripting (font). Our faces also offer the same uniform night time shading and includes the original die cut notches for easy installation. Each kit is made for global distribution, so simply pick out the faces that match your originals. They are available in a variety of colors to make a bold statement, or to match exterior paint schemes. This kit includes faces for: manual transmission / tiptronic transmission / kph / mph / celsi...(choose a part on the right to read more) General Fitment911 1989-94911 1994-98
$595.00
Make a selection ER2290000 Diy kit - front control arm rubber bushings are now available as a kit for self-installation. in addition to a complete set of 4 OEM spec rubber bushings, the kit includes proprietary installation tools and instructions, which are essential for successful installation. use a pipe clamp or shop press to complete the install. General Fitment914 1970-76912 1965-69 911 1965-69 911 1970-73 911 1974-77 930 1975-77 911 1978-83 911 1984-86 911 1987-89
$249.00
Make a selection F6564120106 Instrument faces are one of the most visible and frequently looked at components in your Porsche. When making the decision to change them you want to make ensure that you select a high quality product similar to your originals. Each of our sets are made in Germany and use the factory scripting (font). Our faces also offer the same uniform night time shading and includes the original die cut notches for easy installation. Each kit is made for global distribution, so simply pick out the faces that match your originals. They are available in a variety of colors to make a bold statement, or to match exterior paint schemes. This kit includes faces for: manual transmission / tiptronic transmission / kph / mph / celsi...(choose a part on the right to read more) General Fitment911 1989-94911 1994-98
$603.90
Make a selection F6464120010 Instrument faces are one of the most visible and frequently looked at components in your Porsche. When making the decision to change them you want to make ensure that you select a high quality product similar to your originals. Each of our sets are made in Germany and use the factory scripting (font). Our faces also offer the same uniform night time shading and includes the original die cut notches for easy installation. Each kit is made for global distribution, so simply pick out the faces that match your originals. They are available in a variety of colors to make a bold statement, or to match exterior paint schemes. This kit includes faces for: manual transmission / tiptronic transmission / kph / mph / celsi...(choose a part on the right to read more)
$603.90
Make a selection F6564120105 Instrument faces are one of the most visible and frequently looked at components in your Porsche. When making the decision to change them you want to make ensure that you select a high quality product similar to your originals. Each of our sets are made in Germany and use the factory scripting (font). Our faces also offer the same uniform night time shading and includes the original die cut notches for easy installation. Each kit is made for global distribution, so simply pick out the faces that match your originals. They are available in a variety of colors to make a bold statement, or to match exterior paint schemes. This kit includes faces for: manual transmission / tiptronic transmission / kph / mph / celsi...(choose a part on the right to read more) General Fitment911 1989-94911 1994-98
$603.90
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |