Vehicles
18 not categorized PORSCHE 911 ENGINE NUMBERCan't find what you need? Try browsing the Accessories or Exploded Diagrams!<-- Try narrowing by car using the menu to the left.61607818S Inlet oil line with sleeve & nut, original braided steel (1600 from engine #67001, 1600s from engine #81201). Fits 356, 356a. General Fitment356 1950-59
$198.28
Make a selection 400986 Porsche Boxster, Cayman, and 911 (986/987/996) ln spec k1 connecting rods for 2.5, 2.7, 3.2, & 3.4 m96/m97 engines. Replaces factory connecting rod part number 99610397501. General FitmentBOXSTER 1997-04BOXSTER 2005-08 CAYMAN 2006-08 911 1998-05
$1,185.00
Make a selection FVD99310021 Kit includes: General Fitment911 1994-98
$2,194.50
Make a selection 100103038TU997 Mahle 3.8 liter piston and cylinder conversion kit for 996/997 turbo / GT2 & GT2 rs - increased horsepower and torque.* - forged pistons with deeper, mirrored valve pockets with 23 mm wrist pin. - slip fit, steel (st52) cylinders. - piston pin bore is off center (deaxiert) for factory quiet operation. - 9.4:1 compression. - 102 mm bore. - piston rings installed directly on the pistons for ease of installation. - made in Germany by mahle gmbh. *please note: horsepower and torque gains depend on the software used, camshafts, crankshaft and other internal modifications. 700+ hp and torque can be achieved with use of these pistons and cylinders with a proper engine build and software. Contact your sales person for ...(choose a part on the right to read more) General Fitment911 TURBO/GT2 2001-05911 TURBO/GT2 2007-09
$14,654.60
Make a selection 577000 23 wheel horsepower is gain by adding this intake to your Porsche 996 or 997 car. This intake has been tested numerous times on stock cars at the K&N facility gaining these numbers! General Fitment911 1998-05911 2005-08
$714.99
Make a selection 10606 An interesting fact: did you know the factory thermostat doesn't start to even open until 186.8f and doesn't fully open until almost 210f? did you also know that the new '09 dfi engines run a 176f thermostat? Or how about factory turbo, GT2, and GT3 engines that run with even colder thermostats from the factory? This low temperature thermostat, featuring a calibrated, German-made 160f thermostat pre-installed in a new, oe wahler thermostat housing and gasket, is calibrated to allow thermostat opening a full 20-25f degrees earlier than the factory thermostat. That means that the the low temperature thermostat is designed to be fully open by 180-185f, allowing for full flow to the cooling system to maximize c...(choose a part on the right to read more) General FitmentBOXSTER 1997-04BOXSTER 2005-08 911 1998-05 911 2005-08 CAYMAN 2006-08
$109.99
Make a selection 6895121584CS Ranked number one in the world, austrian manufacturer remus is ahead of the game with their top of the line exhaust systems. At remus, an exhaust is not simply built and put on the market. Each setup is rigorously tested not just for optimum performance, but for the highest quality sound attainable. If they are not perfect, the system is re-engineered and tested until the perfect balance between performance and sound is achieved. Every remus exhaust system is crafted from only the finest titanium and steel, giving it the durability necessary to stand up to the rigors of various driving styles. General Fitment911 2009-12
$4,576.50
Make a selection 6425 The 6al delivers everything the 6a does with the addition of a built-in soft touch rev control. This feature allows you to set an rpm limit to protect the engine from over-rev damage caused by driveline failure or missed shifts. Other msd rpm controls can be connected to the 6al such as a three step module selector or rpm activated switch . The 6al also comes supplied with rubber shock mounts and 3000, 6000, 7000, 8000, rpm modules. All necessary parts and wiring instructions are included. General Fitment911 1987-89911 1984-86 911 1978-83 930 1975-77 911 1974-77 911 1970-73 911 1965-69 944 1989-91 944 1985-88 944 1982-85 924 1986-88 924 1980-85 924 1976-79 914 1970-76 912 1965-69 911 1989-94
$309.95
Make a selection 6890031506 Ranked number one in the world, austrian manufacturer remus is ahead of the game with their top of the line exhaust systems. At remus, an exhaust is not simply built and put on the market. Each setup is rigorously tested not just for optimum performance, but for the highest quality sound attainable. If they are not perfect, the system is re-engineered and tested until the perfect balance between performance and sound is achieved. Every remus exhaust system is crafted from only the finest titanium and steel, giving it the durability necessary to stand up to the rigors of various driving styles. General Fitment911 1998-05911 TURBO/GT2 2001-05
$4,338.90
Make a selection 6893051100 Ranked number one in the world, austrian manufacturer remus is ahead of the game with their top of the line exhaust systems. At remus, an exhaust is not simply built and put on the market. Each setup is rigorously tested not just for optimum performance, but for the highest quality sound attainable. If they are not perfect, the system is re-engineered and tested until the perfect balance between performance and sound is achieved. Every remus exhaust part is crafted from only the finest titanium and steel, giving it the durability necessary to stand up to the rigors of various driving styles. General Fitment911 2005-08
$3,453.30
Make a selection 6896121584CS Ranked number one in the world, austrian manufacturer remus is ahead of the game with their top of the line exhaust systems. At remus, an exhaust is not simply built and put on the market. Each setup is rigorously tested not just for optimum performance, but for the highest quality sound attainable. If they are not perfect, the system is re-engineered and tested until the perfect balance between performance and sound is achieved. Every remus exhaust system is crafted from only the finest titanium and steel, giving it the durability necessary to stand up to the rigors of various driving styles. General Fitment911 2009-12
$4,170.15
Make a selection EM477295 Em-47-7295 dual 44 type 2/4 kit w/ cleaners General Fitment914 1970-76911 1987-89
$1,070.91
Make a selection FVD11004 No engine modifications, easy installation. General Fitment911 1989-94
$2,414.50
Make a selection BAT003 Many pre. 1977 Porsche 911's are not equipped with factory oil plumbing (hard lines and thermostat). In this case fitting an oil cooler requires making a hose run from the rear to the front of the vehicle and back. We find the easiest and most cost effective method of plumbing is to duplicate the factory plumbing route using aeroquip hose and fittings with a mocal oil thermostat and oil cooler. The various kits that we offer to accomplish this task include; one of a number of oil cooler options (some are suitable for both fender or front spoiler location), mocal -12 an oil thermostat with mounting bracket, 30 foot length of aqp -12 an stainless braid 3/4" id hose, 30mm metric to -12 an adaptors for the oil ta...(choose a part on the right to read more) General Fitment911 1974-77911 1965-69 911 1970-73
$985.00
Make a selection BAT004 Many pre. 1977 Porsche 911's are not equipped with factory oil plumbing (hard lines and thermostat). In this case fitting an oil cooler requires making a hose run from the rear to the front of the vehicle and back. We find the easiest and most cost effective method of plumbing is to duplicate the factory plumbing route using aeroquip hose and fittings with a mocal oil thermostat and oil cooler. The various kits that we offer to accomplish this task include; one of a number of oil cooler options (some are suitable for both fender or front spoiler location), mocal -12 an oil thermostat with mounting bracket, 30 foot length of aqp -12 an stainless braid 3/4" id hose, 30 mm metric to -12 an adaptors for the oil t...(choose a part on the right to read more) General Fitment911 1974-77911 1965-69 911 1970-73
$1,029.00
Make a selection BAT005 Many pre. 1977 Porsche 911's are not equipped with factory oil plumbing (hard lines and thermostat). In this case fitting an oil cooler requires making a hose run from the rear to the front of the vehicle and back. We find the easiest and most cost effective method of plumbing is to duplicate the factory plumbing route using aeroquip hose and fittings with a mocal oil thermostat and oil cooler. The various kits that we offer to accomplish this task include; one of a number of oil cooler options (some are suitable for both fender or front spoiler location), mocal -12 an oil thermostat with mounting bracket, 30 foot length of aqp -12 an stainless braid 3/4" id hose, 30 mm metric to -12 an adaptors for the oil t...(choose a part on the right to read more) General Fitment911 1974-77911 1965-69 911 1970-73 928 1978-82
$1,090.00
Make a selection BAT006 Many pre. 1977 Porsche 911's are not equipped with factory oil plumbing (hard lines and thermostat). In this case fitting an oil cooler requires making a hose run from the rear to the front of the vehicle and back. We find the easiest and most cost effective method of plumbing is to duplicate the factory plumbing route using aeroquip hose and fittings with a mocal oil thermostat and oil cooler. The various kits that we offer to accomplish this task include; one of a number of oil cooler options (some are suitable for both fender or front spoiler location), mocal -12 an oil thermostat with mounting bracket, 30 foot length of aqp -12 an stainless braid 3/4" id hose, 30mm metric to -12 an adaptors for the oil ta...(choose a part on the right to read more) General Fitment911 1974-77911 1965-69 911 1970-73
$1,179.45
Make a selection FVD11005 Plug n play mass air flow system General Fitment911 1989-94
$1,754.50
Make a selection OSG915 Os giken super lock limited slip diferential for 43 spline type 915 and type 930 gearbox equipped cars. General Fitment911 1978-83911 1970-73 911 1974-77 930 1975-77 911 1984-86
$2,380.75
Make a selection FSPOR993TSPKGE Product details: General Fitment911 1994-98
From $7,750.00
Make a selection AP9972TT102 With the success of our ypipe kit on the 996tt and 997tt, we did a hybrid and built this new part to work with the OEM intake on the 997.2 turbo. Airflow restrictions can always hamper performance and power and this part like any other does that as well. Our ypipe kit has smooth mandrel 3inch bends from a 4inch collector that goes to the throttlebody. For fitment reasons, we then neck down to 2.25inches to fit on the stock boost hoses. We have incorporated all fittings/sensors that are required. General Fitment911 TURBO/GT2 2010-13
$1,199.95
Make a selection 210111997230 Brombacher 997 tt stainless steel race pipes General Fitment911 TURBO/GT2 2007-09
From $456.50
Make a selection BAT002 Many pre. 1977 Porsche 911's are not equipped with factory oil plumbing (hard lines and thermostat). In this case fitting an oil cooler requires making a hose run from the rear to the front of the vehicle and back. We find the easiest and most cost effective method of plumbing is to duplicate the factory plumbing route using aeroquip hose and fittings with a mocal oil thermostat and oil cooler. The various kits that we offer to accomplish this task include; one of a number of oil cooler options (some are suitable for both fender or front spoiler location), mocal -12 an oil thermostat with mounting bracket, 30 foot length of aqp -12 an stainless braid 3/4" id hose, 30mm metric to -12 an adaptors for the oil ta...(choose a part on the right to read more) General Fitment911 1974-77911 1965-69 911 1970-73
$925.00
Make a selection FVD997100221 Kit includes: General Fitment911 TURBO/GT2 2007-09
$6,818.90
Make a selection FVD99361871 Power gains: + 15 hp & + 13 lb. Ft of torque General Fitment911 1994-98
$2,194.50
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |