Vehicles
22 not categorized PORSCHE 911 ENGINE SEAL KITCan't find what you need? Try browsing the Accessories or Exploded Diagrams!<-- Try narrowing by car using the menu to the left.RK924 When doing a belt service you may notice a little oil around the balance shafts or cam shaft if so, do not ignore this! If the belts become oil soaked it could cost you an engine! So save time and money with our complete reseal kit General Fitment924 1980-85924 1976-79
$93.00
Make a selection RK968 When doing a belt service you may notice a little oil around the balance shafts or cam shaft. Do not ignore this! If the belts become oil soaked it could cost you an engine! So save time and money with our complete reseal kit! General Fitment968 1992-95944 1989-91 944 1985-88
$83.24
Make a selection 100507099 Also use (qty.) (1) 99970728340 o-ring (1) 92810518400 seal General Fitment944 1982-85944 1985-88 944 1989-91
$122.56
Make a selection 99970762540
From $7.00
Make a selection BES99710100SK Exhaust system with valves for the 997 -08 General Fitment911 2005-08
$8,792.70
Make a selection 106082 There are not many warning signs of an impending ims failure short of a “death rattle” that occurs as the bearing fails and comes apart. These kits replace the factory sealed bearing with a new, severe duty custom ceramic hybrid roller ball bearing for reduced friction and superior performance in poorly lubricated operating conditions and replaces the factory ims flange hub, bearing support, and fastener with a stronger, revised billet chromoly assembly. The center bearing support also receives an increase in size and no longer is cut for the o-ring that keep engine oil from leaking out of the engine - we have relocated the o-ring to the ims hub flange for added strength to the center stud & bearing support...(choose a part on the right to read more) General FitmentBOXSTER 2005-08BOXSTER 1997-04 911 1998-05
$681.94
Make a selection 106084 There are not many warning signs of an impending ims failure short of a “death rattle” that occurs as the bearing fails and comes apart. These kits replace the factory sealed bearing with a new, severe duty custom ceramic hybrid roller ball bearing for reduced friction and superior performance in poorly lubricated operating conditions and replaces the factory ims flange hub, bearing support, and fastener with a stronger, revised billet chromoly assembly. The center bearing support also receives an increase in size and no longer is cut for the o-ring that keep engine oil from leaking out of the engine - we have relocated the o-ring to the ims hub flange for added strength to the center stud & bearing support...(choose a part on the right to read more) General FitmentBOXSTER 2005-08BOXSTER 1997-04 911 1998-05 911 1987-89
$899.99
Make a selection AP996TT105 Agency power has just given Porsche 996tt owners another way to get an easy 20 bolt-on horsepower with this new big mouth plenum and throttle body kit. agency power set out to engineer and design a plenum that was functional, did not require additional tuning, and simply. Made power! the plenum is 6061 aluminum that retains the same shape as the factory t pipe. the reason to keep a standard t shape is that the engine works off of pulses. just like how Porsche designed, agency power kept this design and simply improved the restriction, the throttle body. the factory throttle body inlet size is 76mm that then jumps up to a 78mm id plastic plenum. General Fitment911 TURBO/GT2 2001-05
$850.95
Make a selection FVD99710063T FVD "brombacher" level 3 tuning kit for the 2009- 997s includes our FVD flashload software cable, a single user diagnostic tool with software, bmc sport air filter and our "brombacher" stainless steel TUV exhaust system for the 997s-2 dfi. General Fitment911 2009-12
$9,711.90
Make a selection AP997TT105 Adding bolt-on horsepower to the 997 turbo is a continuous quest by many enthusiasts looking for more power. reverting back to old tuning technologies, agency power has developed a larger throttle body and plenum kit for the Porsche 997 turbo to gain added performance. the point of a larger throttle body is to get in more air. The more air you bring in, the more power you make. The 997 turbo's engine intake system works off pulses, so how that air is diverted to either side of the engine is not as important as the volume incoming. General Fitment911 2005-08
$850.95
Make a selection 90110090203 You cannot rebuild without this critical kit! Every gasket and seal you could imagine for a thorough job. Other kits available for larger engine displacements. View/Change Diagram
$332.71
Make a selection 100103038TU997 Mahle 3.8 liter piston and cylinder conversion kit for 996/997 turbo / GT2 & GT2 rs - increased horsepower and torque.* - forged pistons with deeper, mirrored valve pockets with 23 mm wrist pin. - slip fit, steel (st52) cylinders. - piston pin bore is off center (deaxiert) for factory quiet operation. - 9.4:1 compression. - 102 mm bore. - piston rings installed directly on the pistons for ease of installation. - made in Germany by mahle gmbh. *please note: horsepower and torque gains depend on the software used, camshafts, crankshaft and other internal modifications. 700+ hp and torque can be achieved with use of these pistons and cylinders with a proper engine build and software. Contact your sales person for ...(choose a part on the right to read more) General Fitment911 TURBO/GT2 2001-05911 TURBO/GT2 2007-09
$14,654.60
Make a selection BES99710200SK Exhaust system with valves for the 997 -08 General Fitment911 2005-08
$9,385.20
Make a selection BES99720201SK "brombacher" stainless steel exhaust system with valves for the 997-2 General Fitment911 2005-08911 2009-12
$9,992.40
Make a selection BES99720201S8 "brombacher" stainless steel exhaust system for the 997-2 General Fitment911 2009-12
From $7,731.90
Make a selection FVD99710063E FVD "brombacher" level 3 tuning kit for the 2009- 997s includes our FVD flashload software cable, a single user diagnostic tool with software, bmc sport air filter and our "brombacher" stainless steel exhaust system for the 997s-2 dfi. General Fitment911 2009-12
$10,371.90
Make a selection FSPOR911TIC Product details: General Fitment911 1987-89911 1984-86 911 1978-83 930 1975-77
$2,395.00
Make a selection BES99710200S8 Facts: General Fitment911 2005-08
$8,826.40
Make a selection BES99720200SHD "brombacher" stainless steel exhaust system for the 997-2 General Fitment911 2009-12
From $7,994.80
Make a selection 99710420103
View/Change Diagram
From $42.24
Make a selection 029198009 All of the gaskets and seals to completely rebuild your engine except for the front and rear main seals! this kit is specifically for the 1974-75 914 1.8 but contains only muffler gaskets for the 74 muffler. Also order four muffler gaskets if you have a 75 model with the factory heat exchangers. General Fitment914 1970-76
$95.99
Make a selection 10010303000TU Mahle pistons are forged for substantially higher and more uniform strength over pistons that are cast. Mahle cylinders have extremely high thermal resistance and are nikasil coated to reduce wear and friction. We also have the piston rings (sealing and oil scrapers) pre-installed to ensure reliability. Each of our piston and cylinder kits are complete and ready for installation. Features: mahle forged 935 3.0 l turbo pistons mahle nikasil coated cylinders increased 7:1 compression = greater acceleration 95 mm pistons / 95 mm finned wr group 0 cylinders piston rings pre-installed piston pins and circlips are included complete set of 6 - ready for installation made in Germany we recommend the complete engine gas...(choose a part on the right to read more) General Fitment911 1970-73
From $6,197.50
Make a selection 91411600001 Our 18-piece clutch package contains everything we use in our shop for a perfect clutch replacement. beware of lesser kits, you will need all of these parts! Included is the clutch installation manual. Kit includes: rear main seal, throwout bearing, 2 throwout bearing clips, flywheel, front trans. Seal, 2 cv joint gaskets, flywheel o-ring, ball stud cup, 2 muffler gaskets, needle bearing, cv joint bolt, clutch alignment tool, flywheel crush washer, felt washer, pressure plate, clutch disc, clutch installation manual. General Fitment914 1970-76
$917.39
Make a selection 91110090503EQ FVD cylinder head gasket sets contain high quality German sourced gaskets, seals and o-rings. This kit contains a complete set of gaskets to make a teardown / rebuild more convenient. Sold as a complete set. 1 necessary per car. To complete the gasket set for the whole engine order please 91110090705eq too. Only for engines 911.92/93/97/98
$358.60
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |