Vehicles
21 not categorized PORSCHE 911 PROP SHAFTCan't find what you need? Try browsing the Accessories or Exploded Diagrams!<-- Try narrowing by car using the menu to the left.95542101001 - inexpensive alternative to a complete part. - tested quality parts
$178.20
Make a selection 99610515201
From $61.21
Make a selection FVD123041AT FVD Brombacher997.1 tt "700 series" upgraded turbos facts: - cnc re-profiled compressor housing and backing plate - new, lightened and larger compressor wheel (12 blades) - reworked turbine wheel, lightened and optimized for higher flow and reduced backpressure. - all new bearings. - all new piston rings and seals. - all parts cleaned, inspected and measured to motorsport specifications. - all parts are balanced (static & dynamic) up to 120.000 rpm with balancing protocol. - 47.55 mm inducer - 66 mm exducer - flow rate = 37 lbs. / minute or 280g/s - remanufactured by borg warner certified technicians - shaft tolerances are strictly maintained to ensure durability - free software update for those already runn...(choose a part on the right to read more) General Fitment911 TURBO/GT2 2007-09
From $2,644.70
Make a selection 100103038TU997 Mahle 3.8 liter piston and cylinder conversion kit for 996/997 turbo / GT2 & GT2 rs - increased horsepower and torque.* - forged pistons with deeper, mirrored valve pockets with 23 mm wrist pin. - slip fit, steel (st52) cylinders. - piston pin bore is off center (deaxiert) for factory quiet operation. - 9.4:1 compression. - 102 mm bore. - piston rings installed directly on the pistons for ease of installation. - made in Germany by mahle gmbh. *please note: horsepower and torque gains depend on the software used, camshafts, crankshaft and other internal modifications. 700+ hp and torque can be achieved with use of these pistons and cylinders with a proper engine build and software. Contact your sales person for ...(choose a part on the right to read more) General Fitment911 TURBO/GT2 2001-05911 TURBO/GT2 2007-09
$14,654.60
Make a selection 369021072 Flywheel spacer .85mm all 356 & 912 (except super 90). Use only one flywheel spacer to achieve proper crankshaft end play. View/Change Diagram
$40.00
Make a selection ER2290002 Diy kit - rear 914 control arm rubber bushings are now available as a kit for self-installation. in addition to a complete set of 4 OEM spec rubber bushings, the kit includes proprietary installation tools and instructions, which are essential for successful installation plus the rear control arm shafts use a pipe clamp or shop press to complete the install. General Fitment914 1970-76911 1965-69 911 1970-73 911 1974-77 930 1975-77 911 1978-83 911 1984-86 911 1987-89
$439.99
Make a selection 369021077 Flywheel spacer 1.10mm all 356 & 912 (except super 90). Use only one flywheel spacer to achieve proper crankshaft end play. View/Change Diagram
$32.18
Make a selection 029105245B Easily installed especially when doing a clutch job, make sure you check the crankshaft end play and have the appropriate three shims in place. View/Change Diagram
$14.00
Make a selection FVD123041 FVD Brombacher997.1 tt ?700 series? Upgraded turbos General Fitment911 TURBO/GT2 2007-09
$6,531.31
Make a selection 369021071 Flywheel spacer .8mm all 356 & 912 (except super 90). Use only one flywheel spacer to achieve proper crankshaft end play. View/Change Diagram
$39.00
Make a selection FVD123047AT FVD Brombacher997.2 tt ?700 series? Upgraded turbos General Fitment911 TURBO/GT2 2007-09
$3,127.00
Make a selection FVD123042AT FVD Brombacher997.1 tt "700 series" upgraded turbos facts: - cnc re-profiled compressor housing and backing plate - new, lightened and larger compressor wheel (12 blades) - reworked turbine wheel, lightened and optimized for higher flow and reduced backpressure. - all new bearings. - all new piston rings and seals. - all parts cleaned, inspected and measured to motorsport specifications. - all parts are balanced (static & dynamic) up to 120.000 rpm with balancing protocol. - 47.55 mm inducer - 66 mm exducer - flow rate = 37 lbs. / minute or 280g/s - remanufactured by borg warner certified technicians - shaft tolerances are strictly maintained to ensure durability - free software update for those already runn...(choose a part on the right to read more) General Fitment911 TURBO/GT2 2007-09
From $2,644.70
Make a selection STP215 This oil seal arbor is needed for the proper installation of oil seal on flywheel side of crankshaft. please call our office for availability. General Fitment911 1965-69911 1970-73 911 1974-77 930 1975-77
$189.95
Make a selection STP234 This oil seal arbor is needed for the proper installation of oil seal on flywheel side of crankshaft. please call our office for availability. General Fitment928 1978-82928 1983-86 928 1987-91 928 1992-95 944 1982-85 944 1985-88 944 1989-91 968 1992-95 911 1978-83 911 1984-86 911 1987-89 911 1989-94
$375.55
Make a selection FVD123048AT FVD Brombacher997.2 tt ?700 series? Upgraded turbos General Fitment911 TURBO/GT2 2007-09
$3,127.00
Make a selection STP216 This oil seal arbor is needed for the proper installation of oil seal on pulley side of crank shaft. General Fitment911 1987-89911 1984-86 911 1978-83 930 1975-77 911 1974-77 911 1970-73 911 1965-69
$104.50
Make a selection FVD123042 FVD Brombacher997.1 tt ?700 series? Upgraded turbos General Fitment911 TURBO/GT2 2007-09
$5,860.38
Make a selection STP240 This dial gauge holder is needed to properly measure crank shaft flywheel and pulley end-play. Can also be universally to check clearances and run-out. Applicable: most every Porsche and vw air-cooled engine. Please call our office for availability. General Fitment356 1950-59912 1965-69 914 1970-76 911 1965-69 911 1994-98 911 1989-94 911 1987-89 911 1984-86 911 1978-83 930 1975-77 911 1974-77 911 1970-73
$125.55
Make a selection 046105021A The crankshafts on 924s and 944ss are very strong and reliable units that will last a long time if cared for properly. However, if yours needs to be replaced due to a bearing failure or just a low oil pressure problem, we offer rebuilt units at a fraction of the new cost. All rebuilt crankshafts are magna-fluxed to check for cracks and are carefully reground. Specify year and model. All cranks are sold on exchange basis with a core charge, refundable upon receipt of your useable core. View/Change Diagram
From $715.50
Make a selection 10010303204 - 3.2 l for increased horsepower and torque.* - genuine mahle forged pistons with deeper valve pockets. - genuine mahle steel (st52) nikasil coated cylinders.** - piston pin bore is off center (deaxiated) for factory quiet operation. - 10.3:1 compression. - 98 mm big bore. - 22x58 racing wrist pins - 70.4 stroke. - made in Germany by mahle gmbh. - piston rings installed directly on the pistons for ease of installation. - complete set with cylinders, pistons, rings, wrist pins and clips. - kit weighs 21.03 lbs. (9.54 kg). Mahle pistons are forged for substantially higher and more uniform strength over pistons that are cast. Mahle cylinders are manufactured from st52 steel which has extremely high thermal resista...(choose a part on the right to read more)
$9,693.51
Make a selection 10957161 Wider is better! H&r trak+ wheel spacers move your wheels and tires outwards so they are more flush with the fender-instantly giving your vehicle the perfect stance. High end sports car manufacturers use every millimeter of fender space available in their design for the best looks and highest performance and so should you. With trak+ you can fill the gap in your fenders and go wide! General FitmentPANAMERA 2010-14
$107.93
Make a selection 96411691101 Eliminate your clutches slipping and chattering with this genuine kit. We only recommend this kit for non-modified cars that are not running any aftermarket upgrades like exhaust, chip tuning or larger displacements, etc. Complete kit consists of: 1 qty. Clutch disc 1 qty. Pressure plate 1 qty. Release bearing 1 qty. Spline lubricant kit weighs 14.1 lbs. (6.4 kg) tech tip: when you are planning to install a new clutch, it is a good idea to replace the clutch release fork and shaft to ensure proper clutch engagement. Our part # FVD116999 we also recommend a new guide tube 95011681306 for proper installation. View/Change Diagram
From $768.04
Make a selection 100103041TU Mahle 4.1 liter piston and cylinder conversion kit for 996/997 turbo / GT2 & GT2 rs - increased horsepower and torque.* - forged pistons with deeper, mirrored valve pockets. - piston pin bore is off center (deaxiert) for factory quiet operation. - 9.1:1 compression. - 106 mm bore. - piston rings installed directly on the pistons for ease of installation. - made in Germany by mahle gmbh. Water channels and case must be machined to fit. Please add the following to your order: 2 qty. Base gaskets, part # FVD10303905zfd 2 qty. Head gaskets, part # FVD10303905zkd 1 qty. O- ring base set, part # FVD10303905or 1 qty. O- ring head set, part # FVD10303905oro *please note: horsepower and torque gains depend on the softwa...(choose a part on the right to read more) General Fitment911 TURBO/GT2 2007-09911 TURBO/GT2 2001-05
From $8,474.70
Make a selection FVD11690921 Our FVD exclusive line of clutch kits is culmination of Porsche genuine parts, zf sachs race engineering gmbh parts and motorsports parts that have been developed to work together without compromise. They offer a silky-smooth release, superb drivability, quicker acceleration and can handle more torque (575 ft/lbs. / 780 nm max.). This kit includes a clutch disc made with organic friction material with superior thermal resistance, is more resistant to higher rpm's than the oe discs, offers greater longevity and can transmit higher torque. The disc also includes torsion springs that function as a vibration damper between engine and gearbox. That allows for an effortless pedal release when engaging each gear. The...(choose a part on the right to read more) General Fitment911 TURBO/GT2 2007-09911 TURBO/GT2 2001-05 911 1994-98
From $2,757.74
Make a selection 61610216105 Flywheel spacer 3.05mm for super 90. Use only one flywheel spacer to achieve proper crankshaft end play. Special order item. View/Change Diagram
$109.95
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |