Vehicles
155 not categorized PORSCHE 914 EARCan't find what you need? Try browsing the Accessories or Exploded Diagrams!<-- Try narrowing by car using the menu to the left.021109021 Standard type four t4 engine camshaft for all 914 and 912e applications. Your old camshaft may have worn lobes or bearing surfaces. Replace the bearings as long as you are in there. General Fitment912 1965-69914 1970-76
$365.00
Make a selection 021105701A View/Change Diagram
$27.50
Make a selection 021105707A +.25 mm View/Change Diagram
$22.54
Make a selection 021119187 Totally discontinued by the factory and direly needed, these bellows flaps cradles hold the rod that controls the cooling. many in the past removed these flaps thinking that they were going to allow the 914 engine to cool better buy actually it makes the engine run hotter! now everyone has learned and are reinstalling the flaps, needing these cradles. engine uses two. View/Change Diagram
$10.50
Make a selection 021198481A View/Change Diagram
$132.69
Make a selection 029105245B Easily installed especially when doing a clutch job, make sure you check the crankshaft end play and have the appropriate three shims in place. View/Change Diagram
From $14.00
Make a selection 021198483A View/Change Diagram
From $118.28
Make a selection 021198484OR Wonder why your rebuilt engine runs hot and rattles? You forgot to align bore the warped case! Bearings are available in oversize for both the crank and the case side of the bearing. General Fitment914 1970-76
$127.28
Make a selection 021198485A View/Change Diagram
$199.50
Make a selection 021198488OR Wonder why your rebuilt engine runs hot and rattles? You forgot to align bore the warped case! Bearings are available in oversize for both the crank and the case side of the bearing. General Fitment914 1970-76
$127.28
Make a selection
$199.50
Make a selection 021198541 View/Change Diagram
From $30.00
Make a selection 022256511 Rear branch piece clamp. connects the branch piece to the heat exchanger on all 70-74 Porsche 914-4 models View/Change Diagram
$18.50
Make a selection 022906111A We have all been annoyed by the steady speed buck of our 1.7 914. The solution had always been installing a new throttle switch - until the factory discontinued them. We can now offer a replacement circuit board to you. easily installed with the provided rivets, it will permanently solve the steady speed buck that has frustrated you for so long. For 72-73 1.7 models only. View/Change Diagram
From $68.90
Make a selection 039105701 Known as: conrod bearing shell. Sold individually. View/Change Diagram
From $17.49
Make a selection 214310 High grade 5/16" - 24 sae grade 8 bolts for aftermarket cams. Set of three. General Fitment912 1965-69914 1970-76
$4.50
Make a selection 111105313A Fits into the flywheel to guide the input shaft from the transmission. order the felt washer (r111105311) and the locking plate (r021105275) as well. View/Change Diagram
From $7.50
Make a selection
$5.31
Make a selection 111971977 Known as: plug with guide diode single line 930.612.091.00 / plug with guide / plug with guide single line / plug with guide simple / plug with guide single pole View/Change Diagram
From $1.65
Make a selection 20171STD If your cam gear is worn this is a new stock replacement bolt on works with all stock and performance cams. General Fitment914 1970-76
$65.00
Make a selection 90134166100 View/Change Diagram
From $90.15
Make a selection 191598625 Wheel bearing kit. This brand contains: two wheel bearings, one seal, one retaining ring, one nut, and one cotter pin. General Fitment914 1970-76BOXSTER 2005-08
$25.95
Make a selection 111105227 View/Change Diagram
From $2.25
Make a selection
$9.58
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |