Vehicles
361 not categorized PORSCHE 914 ERGCan't find what you need? Try browsing the Accessories or Exploded Diagrams!<-- Try narrowing by car using the menu to the left.90130231802 View/Change Diagram
$24.26
Make a selection 91442459100 These are the very necessary boots that fit at the rear caliper end of the emergency brake cable. you probably did not know that they existed because yours have been gone for so long! easily installed with a little silicone grease. we also have the cable pin and clip available. View/Change Diagram
From $6.25
Make a selection 914511001OP For you serious racers, we offer the one-piece fiberglass hood to cover the headlight boxes. Great for racing where headlights are not required or for the 9014 racers concerned with weight savings. Not for street use General Fitment914 1970-76
$795.00
Make a selection 914204 Will incur higher shipping rates. This is a fiberglass race car part, if cosmetics are important it will need a lot of massaging. General Fitment914 1970-76
$470.00
Make a selection 91442455201 This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or request expedited shipping. View/Change Diagram
From $80.00
Make a selection 91442405301 Exact reproduction of the original 73-76 handbrake lever, this retrofit all models and will easily restore the action to your handbrake. Please see our other listings for the two rear cables and the equalizer cable. View/Change Diagram
From $195.00
Make a selection 90142459301 Known as: ring / rubber ring View/Change Diagram
From $9.52
Make a selection 91450312110 Never perfect will need body and paint work, but not smashed! View/Change Diagram
From $279.00
Make a selection 91450323510 Brand-new and made from our own precise molds, this fiberglass spoiler is one of our most popular items. It replicates the expensive factory special edition spoiler at a fraction of the cost. Part comes in gel-coated black. View/Change Diagram
$274.54
Make a selection MIT1409 Our front and rear stock fiberglass bumpers incorporate both the face bar and rubber top seal into one piece, facilitating installation and saving hundreds over the originals. please keep in mind that fiberglass does not provide the crash protection of steel, but saves weight for autocross and track events! For bumper with oil cooler cut out, use b91450590100. General Fitment914 1970-76
$395.00
Make a selection 91450107510 Just pulled up on the 914 emergency brake handle and it broke off in your hand? The pivot stand has rusted away! Years of hardtop side seal leak directly onto this complex part has caused the problem. Discontinued by the factory in 2001 this identical part is an easy installation after simply sliding out the drivers seat and removing the seat rack and rocker carpet. This part can then be spot welded in. View/Change Diagram
$68.90
Make a selection 91450590100 A perfect match to the oil cooler valance for the ultimate track cooling and factory 914-6 GT identity. This high quality is an exact duplicate of the factory piece and very light for racing applications. General Fitment914 1970-76
$460.00
Make a selection 91442459200 Great reproduction of the discontinued front emergency brake cable boot. two required per car. View/Change Diagram
$10.07
Make a selection 91442424700 Avoid purchasing a costly new emergency handle with these handy repair parts. A little labor and then the brake handle that works like new. View/Change Diagram
$16.42
Make a selection 91450107611 For years, we at the Automobile Atlanta 914 restoration shop when replacing the 914 floor pan, had to fabricate the small tunnel that held the emergency brake equalizer cable. often overlooked and rusted out from years of a leaking hardtop seal, this brand new offering completely replaces the emergency brake equalizer cable tunnel and provides a nice resting place for the original rocker carpet. easily welded in, no floorpan replacement is complete without it. General Fitment914 1970-76
$39.99
Make a selection MIT1407 Achieve the great look of the rare 916 prototype for your 914. Fiberglass bolt-on will also reduce weight. Primed and ready for painting to match your 914. The smooth clean appearance is also aerodynamically efficient! (for stock fenders. Bumper must be slightly modified to fit GT flares.) this part has a lead time of 5-6 weeks. General Fitment914 1970-76
$415.00
Make a selection MIT1412 An exact copy of the 914-6 factory original, this valance is great for custom applications or to replace the nla 1970-71 original. ****note****you have to cut your own hole. General Fitment914 1970-76
$175.00
Make a selection 91451290100 This lid lightens the load for decreased track times and gives your 914 a GT identity. This lid is not for street cars! General Fitment914 1970-76
$675.00
Make a selection MIT1408 Achieve the great look of the rare 916 factory prototype for your 914. Fiberglass bolt-on will also reduce weight. Primed and ready for painting to match your 914. The smooth clean appearance is also aerodynamically efficient! (for stock fenders. Bumper must be slightly modified to fit GT flares) General Fitment914 1970-76
$395.00
Make a selection MIT1433 The perfect complement for the GT flares and what was originally installed on the GT and 916. They tie the look of the flares and finish off the bottom of the car off. This part has to be fitted and body worked. Paint them black as they came from the factory or paint them to match the bodywork. General Fitment914 1970-76
$399.00
Make a selection MIT1410 Our front and rear stock fiberglass bumpers incorporate both the face bar and rubber top seal into one piece, facilitating installation and saving hundreds over the originals. please keep in mind that fiberglass does not provide the crash protection of steel, but saves weight for autocross and track events! General Fitment914 1970-76
$460.00
Make a selection
$199.50
Make a selection MIT1408F Achieve the great look of the rare 916 factory prototype for your 914. Fiberglass bolt-on will also reduce weight. Primed and ready for painting to match your 914. The smooth clean appearance is also aerodynamically efficient! Lead time of 4-8 weeks. General Fitment914 1970-76
$365.00
Make a selection MIT1431 Set of two fiberglass rocker panels. Although we always suggest installing the steel rocker panels, the beautiful fit and appearance of this set is an inexpensive alternative. Install with the set with two rocker panel installation kits. General Fitment914 1970-76
$199.50
Make a selection QRS001 This fiberglass engine shroud is a great replacement for your missing or cracked factory piece. Note: this does not have the oil cooler duct; may not work with some models. Make sure to examine your existing shroud before ordering. This is a special order part. General Fitment911 1974-77930 1975-77 911 1978-83 911 1984-86 911 1987-89 914 1970-76
$689.00
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |