Vehicles
28 not categorized PORSCHE 914 GAS PROPCan't find what you need? Try browsing the Accessories or Exploded Diagrams!<-- Try narrowing by car using the menu to the left.
$120.40
Make a selection 150752 As we all know the only way to install the optional oil pressure gauge is to replace the oil pressure switch with the much "fatter" oil pressure sender. this cannot be accomplished without cutting the sheet metal or extending the hole out of the sheet metal and attaching the sending unit. this hose will give you the needed length. (might need to grind down the male end for a proper fit) General Fitment914 1970-76
$37.95
Make a selection 9712 These chrome lug nuts feature a 60 degree conical seat. 14 mm x 1.5 thread pitch. These lug nuts must be used with the EMPI gas burner style wheels for proper fitment. Sold in a set of four, four sets needed for entire car. General Fitment914 1970-76
$18.81
Make a selection 91420101010 Brand new fuel tank for 1970-early 74 914. ****note****the top center bracket on the tank will need to be ground down 1/2 inch and the hole elongated in order to properly fit the expansion tank. View/Change Diagram
$395.00
Make a selection 9147076KIT For the first time in recorded 914 history comes and all in one complete interior hardware kit. every nut and bolt and screw and clip that you need to reassembly you interior in one carefully put together kit. dr 914 worked with the winzer hardware representative in one three hour session pouring over the original Porsche 914 factory parts catalog calling out every piece of hardware famous "8" body section of the book. now with the exception of the seat belt bolts you can own with one click of the mouse, every piece of hardware missing from that basket case 914 you purchased. carefully labeled as to its use, and including rockers spoilers and valance hardware, you will be delighted to install this beautif...(choose a part on the right to read more) General Fitment914 1970-76
$225.00
Make a selection 91450193571 Shroud identical to the factory GT part, this neat item fits perfectly over the GT cooler as well as snugly against the 1970-72 front panel (1973-76 cars need slight trimming of the shroud). Ultimate cooling will result when this shroud is properly installed. General Fitment914 1970-76
$195.50
Make a selection 90155921020E Replace your old or faded badge with a beautiful new one and get all the parts to do it properly. This kit includes a new gold-tone Porsche hood badge, badge gasket, and two emblem nuts. General Fitment911 1965-69944 1982-85 944 1985-88 944 1989-91 968 1992-95 924 1976-79 924 1980-85 924 1986-88 914 1970-76 912 1965-69 911 1984-86 911 1970-73 911 1974-77 930 1975-77 911 1978-83 911 1987-89 911 1989-94 911 1994-98 928 1978-82 928 1983-86 928 1987-91 928 1992-95
$182.24
Make a selection 169515 This kit is used when removing your old stock freeze type plugs from your case to allow you to clean all the oil galleys properly. You will have to tap these galleys to run these plugs. Also reduces the risk of having a stock one pop out and loose oil pressure. Set of 12. General Fitment914 1970-76912 1965-69
$16.47
Make a selection 914PRT Who wants to constantly perform the dirty, greasy pushrod tube replacement procedure when these space age viton seals eliminate the problem for years! rated at 450. Degrees, if installed properly you should never have to replace the seals again! Kit comes complete with precise instructions and valve cover gaskets. Everything you need except hand cleaner! Consists of: 8 b021 109 345 a; 2 r021 101 481; 1 rtc 1022 make sure that you readjust the valves and check the valve adjuster lugs for damage. General Fitment914 1970-76
$46.92
Make a selection STP225 This synchro engagement kit is needed for the proper removal of syncro rings from the gear. Does third through fifth on 915 transmissions, all gears on 901 transmissions please call our office for availability. General Fitment911 1970-73911 1974-77 911 1978-83 911 1984-86 912 1965-69 914 1970-76
$275.55
Make a selection STTRIPS As sport rules changes and new safety features are required GTS classics have created the "trips" device. On all our seats are 4 mountings that hold these devices at your desired and needed height and keeps them in place. The "trips" device ensures that your shoulder harness is properly guided and safe. General Fitment356 1950-59356 1960-65 912 1965-69 914 1970-76 911 1965-69 911 1970-73
$189.00
Make a selection RSRRCOK914W This kit allows you the suspension adjustment that had previously been reserved for pure race cars. General Fitment914 1970-76
$239.50
Make a selection VDO360006 This is the sending unit needed to use the vdo 80 psi oil pressure gauge, part number rvdo350040. This unit is appropriate for most four-cylinder engines. General FitmentALL914 1970-76
$98.50
Make a selection RSRRCOK914 This kit allows you the suspension adjustment that had previously been reserved for pure race cars. General Fitment914 1970-76
$595.00
Make a selection STP240 This dial gauge holder is needed to properly measure crank shaft flywheel and pulley end-play. Can also be universally to check clearances and run-out. Applicable: most every Porsche and vw air-cooled engine. Please call our office for availability. General Fitment356 1950-59912 1965-69 914 1970-76 911 1965-69 911 1994-98 911 1989-94 911 1987-89 911 1984-86 911 1978-83 930 1975-77 911 1974-77 911 1970-73
$125.55
Make a selection AAA25600C This kit consists of all the proper hardware to install heat exchangers and a muffler, including the rare copper locking nuts to ensure a perfect installation. Remember to install the exchangers one at a time and torque in an x pattern to 18 ft lbs. General Fitment914 1970-76
$69.92
Make a selection VDO360025 This is the sending unit needed to use the vdo 150psi oil pressure gauge, part number rvdo350041. This unit is appropriate for most four-cylinder engines. General Fitment914 1970-76924 1986-88
$93.00
Make a selection AAA25600A This kit consists of all the proper hardware to install heat exchangers and a muffler, including the rare copper locking nuts to ensure a perfect installation. Remember to install the exchangers one at a time and torque in an x pattern to 18 ft lbs. General Fitment914 1970-76
$66.40
Make a selection AAA25600B This kit consists of all the proper hardware to install heat exchangers and a muffler, including the rare copper locking nuts to ensure a perfect installation. Remember to install the exchangers one at a time and torque in an x pattern to 18 ft lbs. General Fitment914 1970-76
$71.62
Make a selection 100103041TU Mahle 4.1 liter piston and cylinder conversion kit for 996/997 turbo / GT2 & GT2 rs - increased horsepower and torque.* - forged pistons with deeper, mirrored valve pockets. - piston pin bore is off center (deaxiert) for factory quiet operation. - 9.1:1 compression. - 106 mm bore. - piston rings installed directly on the pistons for ease of installation. - made in Germany by mahle gmbh. Water channels and case must be machined to fit. Please add the following to your order: 2 qty. Base gaskets, part # FVD10303905zfd 2 qty. Head gaskets, part # FVD10303905zkd 1 qty. O- ring base set, part # FVD10303905or 1 qty. O- ring head set, part # FVD10303905oro *please note: horsepower and torque gains depend on the softwa...(choose a part on the right to read more) General Fitment911 TURBO/GT2 2007-09911 TURBO/GT2 2001-05
From $8,474.70
Make a selection 000043018001 Reinstall your turbo properly. It is not easy, so do it once, by doing it right! We highly recommend this installation kit with all replacement turbo chambers, hardware, and gaskets. Turbocharger not included. General Fitment924 1976-79924 1980-85
$794.23
Make a selection 10010303204 - 3.2 l for increased horsepower and torque.* - genuine mahle forged pistons with deeper valve pockets. - genuine mahle steel (st52) nikasil coated cylinders.** - piston pin bore is off center (deaxiated) for factory quiet operation. - 10.3:1 compression. - 98 mm big bore. - 22x58 racing wrist pins - 70.4 stroke. - made in Germany by mahle gmbh. - piston rings installed directly on the pistons for ease of installation. - complete set with cylinders, pistons, rings, wrist pins and clips. - kit weighs 21.03 lbs. (9.54 kg). Mahle pistons are forged for substantially higher and more uniform strength over pistons that are cast. Mahle cylinders are manufactured from st52 steel which has extremely high thermal resista...(choose a part on the right to read more)
$9,693.51
Make a selection 100103038TU997 Mahle 3.8 liter piston and cylinder conversion kit for 996/997 turbo / GT2 & GT2 rs - increased horsepower and torque.* - forged pistons with deeper, mirrored valve pockets with 23 mm wrist pin. - slip fit, steel (st52) cylinders. - piston pin bore is off center (deaxiert) for factory quiet operation. - 9.4:1 compression. - 102 mm bore. - piston rings installed directly on the pistons for ease of installation. - made in Germany by mahle gmbh. *please note: horsepower and torque gains depend on the software used, camshafts, crankshaft and other internal modifications. 700+ hp and torque can be achieved with use of these pistons and cylinders with a proper engine build and software. Contact your sales person for ...(choose a part on the right to read more) General Fitment911 TURBO/GT2 2001-05911 TURBO/GT2 2007-09
$14,654.60
Make a selection 10095716 Wider is better! H&r trak+ wheel spacers move your wheels and tires outwards so they are more flush with the fenderinstantly giving your vehicle the perfect stance. High end sports car manufacturers use every millimeter of fender space available in their design for the best looks and highest performance and so should you. With trak+ you can fill the gap in your fenders and go wide! General Fitment911 1989-94911 1994-98
$364.43
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |