Vehicles
399 not categorized PORSCHE 914 IMS CHECKCan't find what you need? Try browsing the Accessories or Exploded Diagrams!<-- Try narrowing by car using the menu to the left.91431802901 If your speedometer completely fails look at the angle drive first before suspecting the cable. easily checked by disconnecting the speedometer cable then lifting the car and putting it in gear to see if the angle drive spins, the part is easily replaced. always try to buy a new one as this is a wear part. purchase a speedo angle drive seal at the same time to stop the transmission fluid leak. it fits on the drive gear in the rear tail cover and is easily removed with the rear 13mm headed set screw. (you will have a fluid spill when this is removed so get ready!) refill with 80/90 weight oil only. View/Change Diagram
From $52.47
Make a selection 029105245B Easily installed especially when doing a clutch job, make sure you check the crankshaft end play and have the appropriate three shims in place. View/Change Diagram
From $14.00
Make a selection 91450415510 A must have part for engine cooling. replace this part when the engine is out and clean the bay at the same time! this part is for the drivers and passengers side only check all engine sheet metal boots and seals while you are at it for the best cooling. View/Change Diagram
From $19.00
Make a selection 914PRT Who wants to constantly perform the dirty, greasy pushrod tube replacement procedure when these space age viton seals eliminate the problem for years! rated at 450. Degrees, if installed properly you should never have to replace the seals again! Kit comes complete with precise instructions and valve cover gaskets. Everything you need except hand cleaner! Consists of: 8 b021 109 345 a; 2 r021 101 481; 1 rtc 1022 make sure that you readjust the valves and check the valve adjuster lugs for damage. General Fitment914 1970-76
$46.92
Make a selection AAA25600C This kit consists of all the proper hardware to install heat exchangers and a muffler, including the rare copper locking nuts to ensure a perfect installation. Remember to install the exchangers one at a time and torque in an x pattern to 18 ft lbs. General Fitment914 1970-76
$69.92
Make a selection 150PB00741 Restore precise shifting with this set of polyurethane coupler bushings. This replaces the original rubber bushings inside of OEM part # 91142402404 . To save installation cost / time, we recommend installing a new conical screw, part # 90142422900 coupler sleeves, part # 91142429400 and 91142429200 be sure to check / replace the shift rod bushing as well, part # 91142413900 , the friction ring, part # 91442422400 and rod bushing conical screw, part # 90142422900 sold individually. 1 necessary per car. General Fitment356 1960-65914 1970-76 911 1970-73
$58.30
Make a selection P226A If you 914-6 and early 911 owners experience loss of power at high speeds or low speed rich running and you haven’t checked the float lever, you’ve missed an important diagnosis. Float level is critical for proper carb tuning. This custom designed tool easily accesses the float bowl and is calibrated for precise measure. General Fitment911 1965-69911 1970-73 914 1970-76 356 1960-65 356 1950-59 912 1965-69 911 1974-77 911 1978-83 911 1984-86 911 1987-89
$48.00
Make a selection PP912227 914 door check strap rollers are notorious for falling apart and making life difficult when opening and closing your door. The original cheap plastic rollers quickly wear or break, causing a stiff or non-operational door. Our improved rollers are made from a self lubricating plastic. Their dry-running nature means dirt particles do not stick to the surface, but instead deflect off it. For this reason, optimal performance can be maintained even in extremely dirty environments. We even throw in new steel roller shafts for a complete rebuild. At prices at over $75.00 for a new check strap, our kit looks pretty good. Installation is easy with normal hand tools. One kit per door. General Fitment914 1970-76
$58.50
Make a selection FVD347911930 This cost-effective spacer kit assists with bump steer by raising the steering rack by 10 mm. That improves the angle of the tie rods and helps to compensate for bump steer. Features: high quality lightweight aluminum spacers includes extra bolts for differing applications made in Germany sold as a kit. 1 necessary per car. General Fitment914 1970-76
$24.20
Make a selection RSRBSKLSB Availability will be checked upon ordering General Fitment914 1970-76911 1978-83 911 1984-86 911 1970-73 911 1974-77 930 1975-77 911 1987-89
$34.95
Make a selection TL1021 This universal flywheel lock has been designed for use on all air-cooled Porsche engines (series 356, 912, 914 & all 911s through 1969) and on all air-cooled volkswagen engines (type 1,2,3 & 4). This tool is a must when changing a flywheel or its seal and it comes in handy when changing a clutch. Made from a forging, this quality tool will last a lifetime. Gpcg91101000. General Fitment914 1970-76356 1950-59 356 1960-65 912 1965-69 911 1994-98 911 1989-94 911 1987-89 911 1984-86 911 1978-83 930 1975-77 911 1974-77 911 1970-73 911 1965-69
$12.00
Make a selection ACCC107095 This unique tool has been designed to measure the end play movement of the vw crankshaft without the use of a dial indicator. All that is necessary is a feeler gauge set and this tool. With the tool bolted to the end of the case, the feeler gauge measures the gap created by the end play. The taking of this end play measurement is necessary whenever a vw engine is rebuilt to prevent the rear main bearing from seizing up. A must for rebuilding one engine or many, this tool works on all air-cooled vw engines and Porsche 912 & 914 models. Imperative when installing a new flywheel, to recheck and set the rear end play! General Fitment356 1950-59356 1960-65 912 1965-69 914 1970-76
$35.00
Make a selection 021119957 This is an autoatlanta exclusive oil pressure switch boot for all 914-4 models. believe it or not your 914 had this factory installed. long gone on most engines by now this part is critical to seal in the cooling air. easily installed, this part fits behind the distributor. please check the oil pressure switch for leaks at the same time. View/Change Diagram
$13.00
Make a selection AAA25600A This kit consists of all the proper hardware to install heat exchangers and a muffler, including the rare copper locking nuts to ensure a perfect installation. Remember to install the exchangers one at a time and torque in an x pattern to 18 ft lbs. General Fitment914 1970-76
$66.40
Make a selection AAA25600B This kit consists of all the proper hardware to install heat exchangers and a muffler, including the rare copper locking nuts to ensure a perfect installation. Remember to install the exchangers one at a time and torque in an x pattern to 18 ft lbs. General Fitment914 1970-76
$71.62
Make a selection 000043152124XR Genuine set of plush velour floor mats with nubuck edging that is custom tailored for your Porsche. Each is cut, sewn and trimmed to fit perfectly. They include a non-slip and waterproof rubber backing and are secured with a new updated fastening system. Limited availability due to color. If you don't see the color you require please contact an FVD parts specialist. Please note: these are for left hand drive models only.
From $204.08
Make a selection 000924 Why buy a rebuilt engine or transmission from us when your mechanic says he can do it cheaper? Because at Automobile Atlanta, we don’t compromise your rebuild with substandard parts or machine work. We go overboard in replacing parts your mechanic would never think to or can’t readily purchase. Plus, from years of experience, we know what wears out. Our rebuilt engine or transmission will, with care, last as long as the new factory one. Our setup is without compromise. We have invested thousands in Porsche factory tools to insure our engines and transmissions are “spot on”. Finally, they are extensively checked during each step of the rebuild process so your new engine is ready to bolt-in and drive away...(choose a part on the right to read more) General Fitment924 1980-85924 1976-79
$4,187.00
Make a selection 000944 Why buy a rebuilt engine or transmission from us when your mechanic says he can do it cheaper? Because at Automobile Atlanta, we don’t compromise your rebuild with substandard parts or machine work. We go overboard in replacing parts your mechanic would never think to or can’t readily purchase. Plus, from years of experience, we know what wears out. Our rebuilt engine or transmission will, with care, last as long as the new factory one. Our setup is without compromise. We have invested thousands in Porsche factory tools to insure our engines and transmissions are “spot on”. Finally, they are extensively checked during each step of the rebuild process so your new engine is ready to bolt-in and drive away...(choose a part on the right to read more) General Fitment924 1986-88944 1985-88 944 1982-85
$10,600.00
Make a selection 000944S Why buy a rebuilt engine or transmission from us when your mechanic says he can do it cheaper? Because at Automobile Atlanta, we don’t compromise your rebuild with substandard parts or machine work. We go overboard in replacing parts your mechanic would never think to or can’t readily purchase. Plus, from years of experience, we know what wears out. Our rebuilt engine or transmission will, with care, last as long as the new factory one. Our setup is without compromise. We have invested thousands in Porsche factory tools to insure our engines and transmissions are “spot on”. Finally, they are extensively checked during each step of the rebuild process so your new engine is ready to bolt-in and drive away...(choose a part on the right to read more) General Fitment944 1985-88
$10,600.00
Make a selection 000944S2 Why buy a rebuilt engine or transmission from us when your mechanic says he can do it cheaper? Because at Automobile Atlanta, we don’t compromise your rebuild with substandard parts or machine work. We go overboard in replacing parts your mechanic would never think to or can’t readily purchase. Plus, from years of experience, we know what wears out. Our rebuilt engine or transmission will, with care, last as long as the new factory one. Our setup is without compromise. We have invested thousands in Porsche factory tools to insure our engines and transmissions are “spot on”. Finally, they are extensively checked during each step of the rebuild process so your new engine is ready to bolt-in and drive away...(choose a part on the right to read more) General Fitment944 1989-91
$7,367.00
Make a selection 000944T Why buy a rebuilt engine or transmission from us when your mechanic says he can do it cheaper? Because at Automobile Atlanta, we don’t compromise your rebuild with substandard parts or machine work. We go overboard in replacing parts your mechanic would never think to or can’t readily purchase. Plus, from years of experience, we know what wears out. Our rebuilt engine or transmission will, with care, last as long as the new factory one. Our setup is without compromise. We have invested thousands in Porsche factory tools to insure our engines and transmissions are “spot on”. Finally, they are extensively checked during each step of the rebuild process so your new engine is ready to bolt-in and drive away...(choose a part on the right to read more) General Fitment944 1989-91944 1985-88
$10,600.00
Make a selection 000968 Why buy a rebuilt engine or transmission from us when your mechanic says he can do it cheaper? Because at Automobile Atlanta, we don’t compromise your rebuild with substandard parts or machine work. We go overboard in replacing parts your mechanic would never think to or can’t readily purchase. Plus, from years of experience, we know what wears out. Our rebuilt engines will, with care, last as long as the new factory one. Our setup is without compromise. We have invested thousands in Porsche factory tools to insure our engines are “spot on.” finally, they are extensively checked during each step of the rebuild process so your new engine is ready to bolt-in and drive away. Rebuilt engines need a 30 day l...(choose a part on the right to read more) General Fitment968 1992-95
$7,367.00
Make a selection 055100500009 The techart program is exclusively developed by their designers, engineers, technicians and model builders. Working closely together, the team designs, builds prototypes and tests the parts in the wind tunnel until each item is approved for road-legal use and launched for the worldwide market. Every component is manufactured from select materials to exacting quality norms. General FitmentCAYENNE 2007-10
$3,638.25
Make a selection 055100196009 The techart program is exclusively developed by their designers, engineers, technicians and model builders. Working closely together, the team designs, builds prototypes and tests the parts in the wind tunnel until each item is approved for road-legal use and launched for the worldwide market. Every component is manufactured from select materials to exacting quality norms. General FitmentCAYENNE 2007-10
$5,933.25
Make a selection 055100200009 The techart program is exclusively developed by their designers, engineers, technicians and model builders. Working closely together, the team designs, builds prototypes and tests the parts in the wind tunnel until each item is approved for road-legal use and launched for the worldwide market. Every component is manufactured from select materials to exacting quality norms. General FitmentCAYENNE 2007-10
$877.50
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |