Vehicles
21 not categorized PORSCHE 924 PROP SHAFTCan't find what you need? Try browsing the Accessories or Exploded Diagrams!<-- Try narrowing by car using the menu to the left.95542101001 - inexpensive alternative to a complete part. - tested quality parts
$178.20
Make a selection 99610515201
From $61.21
Make a selection 046105021A The crankshafts on 924s and 944ss are very strong and reliable units that will last a long time if cared for properly. However, if yours needs to be replaced due to a bearing failure or just a low oil pressure problem, we offer rebuilt units at a fraction of the new cost. All rebuilt crankshafts are magna-fluxed to check for cracks and are carefully reground. Specify year and model. All cranks are sold on exchange basis with a core charge, refundable upon receipt of your useable core. View/Change Diagram
From $715.50
Make a selection 94410201513 The crankshafts on 924s and 944ss are very strong and reliable units that will last a long time if cared for properly. However, if yours needs to be replaced due to a bearing failure or just a low oil pressure problem, we offer rebuilt units at a fraction of the new cost. All rebuilt crankshafts are magna-fluxed to check for cracks and are carefully reground. Specify year and model. All cranks are sold on exchange basis with a core charge, refundable upon receipt of your useable core. View/Change Diagram
From $698.78
Make a selection STP231 This balance shaft oil arbor needed for the proper installation of the balance shaft oil seal. Applicable: Porsche model 944. Please call our office for availability. General Fitment944 1989-91944 1985-88 944 1982-85 924 1986-88
$59.95
Make a selection STP232 This locking bar is needed to properly secure the balance shaft sprocket from rotating during removal and reinstallation of retaining bolt. General Fitment944 1982-85944 1985-88 944 1989-91 924 1986-88
$39.99
Make a selection 029105245B Easily installed especially when doing a clutch job, make sure you check the crankshaft end play and have the appropriate three shims in place. View/Change Diagram
$14.00
Make a selection 10010303204 - 3.2 l for increased horsepower and torque.* - genuine mahle forged pistons with deeper valve pockets. - genuine mahle steel (st52) nikasil coated cylinders.** - piston pin bore is off center (deaxiated) for factory quiet operation. - 10.3:1 compression. - 98 mm big bore. - 22x58 racing wrist pins - 70.4 stroke. - made in Germany by mahle gmbh. - piston rings installed directly on the pistons for ease of installation. - complete set with cylinders, pistons, rings, wrist pins and clips. - kit weighs 21.03 lbs. (9.54 kg). Mahle pistons are forged for substantially higher and more uniform strength over pistons that are cast. Mahle cylinders are manufactured from st52 steel which has extremely high thermal resista...(choose a part on the right to read more)
$9,693.51
Make a selection 100103038TU997 Mahle 3.8 liter piston and cylinder conversion kit for 996/997 turbo / GT2 & GT2 rs - increased horsepower and torque.* - forged pistons with deeper, mirrored valve pockets with 23 mm wrist pin. - slip fit, steel (st52) cylinders. - piston pin bore is off center (deaxiert) for factory quiet operation. - 9.4:1 compression. - 102 mm bore. - piston rings installed directly on the pistons for ease of installation. - made in Germany by mahle gmbh. *please note: horsepower and torque gains depend on the software used, camshafts, crankshaft and other internal modifications. 700+ hp and torque can be achieved with use of these pistons and cylinders with a proper engine build and software. Contact your sales person for ...(choose a part on the right to read more) General Fitment911 TURBO/GT2 2001-05911 TURBO/GT2 2007-09
$14,654.60
Make a selection 100103041TU Mahle 4.1 liter piston and cylinder conversion kit for 996/997 turbo / GT2 & GT2 rs - increased horsepower and torque.* - forged pistons with deeper, mirrored valve pockets. - piston pin bore is off center (deaxiert) for factory quiet operation. - 9.1:1 compression. - 106 mm bore. - piston rings installed directly on the pistons for ease of installation. - made in Germany by mahle gmbh. Water channels and case must be machined to fit. Please add the following to your order: 2 qty. Base gaskets, part # FVD10303905zfd 2 qty. Head gaskets, part # FVD10303905zkd 1 qty. O- ring base set, part # FVD10303905or 1 qty. O- ring head set, part # FVD10303905oro *please note: horsepower and torque gains depend on the softwa...(choose a part on the right to read more) General Fitment911 TURBO/GT2 2007-09911 TURBO/GT2 2001-05
From $8,474.70
Make a selection 22011090102ATK Sport throttle bodies are a great addition for those with highly modified cars. They are a great addition for those with full exhaust systems (larger diameters), maf kits, larger displacements, street or race cams, etc. The remanufacturing process includes full inspection of your throttle body to ensure proper operation after the remanufacturing process. We then disassemble and bore the original to a 2.7-inch (70.5 mm) diameter. The entire throttle body is cleaned, degreased and the internals are polished to create more laminar flow. We then machine the shaft to accept larger butterfly's which seamlessly match the bore. All clearances are checked for precision to ensure reliability. Each throttle body is reman...(choose a part on the right to read more)
$440.00
Make a selection 10957161 Wider is better! H&r trak+ wheel spacers move your wheels and tires outwards so they are more flush with the fender-instantly giving your vehicle the perfect stance. High end sports car manufacturers use every millimeter of fender space available in their design for the best looks and highest performance and so should you. With trak+ you can fill the gap in your fenders and go wide! General FitmentPANAMERA 2010-14
$107.93
Make a selection 369021072 Flywheel spacer .85mm all 356 & 912 (except super 90). Use only one flywheel spacer to achieve proper crankshaft end play. View/Change Diagram
$40.00
Make a selection 220110906 A sport throttle body is a perfect upgrade for modified cars. The added air mass and velocity enhances performance from exhaust systems (larger diameters), air intake kits, larger displacements, street or race cams, a larger turbo, etc. The remanufacturing process includes full inspection of your throttle body to ensure proper operation after the remanufacturing process. We then disassemble and bore the original 2.4-inch (63 mm) to a 2.6-inch (65 mm) diameter. The entire throttle body is cleaned, degreased and the internals are polished to create more laminar flow. We then machine the shaft to accept larger butterfly's which seamlessly match the bore. All clearances are checked for precision to ensure reliabil...(choose a part on the right to read more) General Fitment911 1989-94
From $485.10
Make a selection 220110932ATK Sport throttle bodies are a great addition for those with highly modified cars. They are a great addition for those with full exhaust systems (larger diameters), maf kits, larger displacements, street or race cams, etc. The remanufacturing process includes full inspection of your throttle body to ensure proper operation after the remanufacturing process. We then disassemble and bore the original 2.4-inch (63 mm) to a 2.6-inch (66.5 mm) diameter. The entire throttle body is cleaned, degreased and the internals are polished to create more laminar flow. We then machine the shaft to accept larger butterfly's which seamlessly match the bore. All clearances are checked for precision to ensure reliability. FVD thrott...(choose a part on the right to read more)
$485.10
Make a selection 369021071 Flywheel spacer .8mm all 356 & 912 (except super 90). Use only one flywheel spacer to achieve proper crankshaft end play. View/Change Diagram
$39.00
Make a selection 96411691101 Eliminate your clutches slipping and chattering with this genuine kit. We only recommend this kit for non-modified cars that are not running any aftermarket upgrades like exhaust, chip tuning or larger displacements, etc. Complete kit consists of: 1 qty. Clutch disc 1 qty. Pressure plate 1 qty. Release bearing 1 qty. Spline lubricant kit weighs 14.1 lbs. (6.4 kg) tech tip: when you are planning to install a new clutch, it is a good idea to replace the clutch release fork and shaft to ensure proper clutch engagement. Our part # FVD116999 we also recommend a new guide tube 95011681306 for proper installation. View/Change Diagram
From $768.04
Make a selection FVD1169093 Our FVD exclusive line of clutch kits is culmination of Porsche genuine parts, zf sachs race engineering gmbh parts and motorsports parts that have been developed to work together without compromise. This kit has a rigid hub with organic friction material with superior thermal resistance, is more resistant to higher rpm's than the oe discs, offers greater longevity and can transmit higher torque. The lightweight flywheel allows the engine to rev more freely which means quicker acceleration, faster shifts and getting into the power band more quickly. It is an ideal kit for highly modified street or track car. This kit can handle more torque (700 ft/lbs. / 950 nm max.). But, please keep in mind that if you plan ...(choose a part on the right to read more) General Fitment911 TURBO/GT2 2007-09911 TURBO/GT2 2001-05 911 1994-98
From $2,608.63
Make a selection 61610216105 Flywheel spacer 3.05mm for super 90. Use only one flywheel spacer to achieve proper crankshaft end play. Special order item. View/Change Diagram
$109.95
Make a selection 220110901ATK Sport throttle bodies are a great addition for those with highly modified cars. They are a great addition for those with full exhaust systems (larger diameters), maf kits, larger displacements, street or race cams, etc. The remanufacturing process includes full inspection of your throttle body to ensure proper operation after the remanufacturing process. We then disassemble and bore the original to a 2.8-inch (71 mm) diameter. The entire throttle body is cleaned, degreased and the internals are polished to create more laminar flow. We then machine the shaft to accept larger butterfly's which seamlessly match the bore. All clearances are checked for precision to ensure reliability. Each throttle body is remanuf...(choose a part on the right to read more)
$485.10
Make a selection FVD1169052 Our FVD exclusive line of clutch kits is culmination of Porsche genuine parts, zf sachs race engineering gmbh parts and motorsports parts that have been developed to work together without compromise. They offer a silky smooth release, superb drivability, can handle more torque (350 ft/lbs. / 475 nm max.) than comparable stage 1 type recommendations. We specifically chose a clutch disc with torsion springs that function as a vibration damper between engine and gearbox, in order to give you an effortless release in 1st gear. The disc also contains sintered metal plates that have a higher friction coefficient than plates with organic friction. A sintered disc allows for higher transmittable torque and is more dirt...(choose a part on the right to read more) General Fitment911 1994-98911 1989-94
From $2,322.25
Make a selection FVD116103 Hailing from the baden wurttemberg region in Germany, speaking the language and dealing with lead engineers from the OEM and motor sport manufacturers for more than 30+ years has many advantages. Our FVD exclusive line of clutch kits is culmination of Porsche genuine parts, zf sachs race engineering gmbh parts and motorsports parts that have been developed to work together without compromise. They offer a silky smooth release, superb drivability, can handle more torque (442 ft/lbs. / 600 nm max.). Than comparable stage 1 type recommendations. These kits are perfect for street and light track use. We specifically chose a clutch disc with torsion springs that function as a vibration damper between engine and gear...(choose a part on the right to read more) General Fitment911 TURBO/GT2 2001-05911 1994-98 911 1989-94
From $1,827.82
Make a selection ER2290002 Diy kit - rear 914 control arm rubber bushings are now available as a kit for self-installation. in addition to a complete set of 4 OEM spec rubber bushings, the kit includes proprietary installation tools and instructions, which are essential for successful installation plus the rear control arm shafts use a pipe clamp or shop press to complete the install. General Fitment914 1970-76911 1965-69 911 1970-73 911 1974-77 930 1975-77 911 1978-83 911 1984-86 911 1987-89
$439.99
Make a selection FVD116102 The discs rigid hub with organic friction material has superior thermal resistance, is more resistant to higher rpm's than the oe discs, offers greater longevity and is able to transmit higher torque (370 ft/lbs. / 500 nm max.). It is an ideal kit for lightly modified street or light use track cars. Clutch kit is made in Germany and includes: 1 qty. Clutch disc (zf sachs race engineering, gmbh) 1 qty. Pressure plate (zf sachs race engineering, gmbh) 1 qty. Release bearing 1 qty. Spline lubricant 9 qty. Pressure plate screws kit weighs 13 lbs. (6 kg) tech tip: when you are planning to install a new clutch, it is a good idea to replace the clutch release fork and shaft to ensure proper clutch engagement. Our par...(choose a part on the right to read more) General Fitment911 GT3 2007-11911 GT3 2003-05 911 1994-98 911 1989-94
From $1,243.90
Make a selection 99311691101 Eliminate your clutches slipping and chattering with this genuine kit. We only recommend this kit for non-modified cars that are not running any aftermarket upgrades like exhaust, chip tuning or larger displacements, etc. Complete kit consists of: 1 qty. Clutch disc 1 qty. Pressure plate 1 qty. Release bearing 1 qty. Spline lubricant kit weighs 14.1 lbs. (6.4 kg) tech tip: when you are planning to install a new clutch, it is a good idea to replace the clutch release fork and shaft to ensure proper clutch engagement, our part # FVD116999. We also recommend a new guide tube 95011681306 for proper installation. View/Change Diagram
From $768.04
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |