Vehicles
16 not categorized PORSCHE 930 SECURING PINCan't find what you need? Try browsing the Accessories or Exploded Diagrams!95511026900 Known as: bolt / bolt locking device View/Change Diagram
From $7.50
Make a selection STP214 This chain tensioner is crucial for securing tensioners in their retracted position during installation. This tool assists in keeping the chain timing correct during this procedure. General Fitment930 1975-77911 1974-77 911 1970-73 911 1965-69
$24.95
Make a selection 90135191615 Small securing clip that goes into the small hole in the brake cross pin. View/Change Diagram
From $46.65
Make a selection 90173111101EQ Aftermarket door mirror with planed glass. This is the perfect finishing detail for a restoration, paint correction or replacement. The glass is planed so that your rear vision is not distorted. Includes: chrome adjustable mirror housing planed mirror glass base gasket securing screws, washers and nuts. Please note: please check the model fitment tab to ensure accurate fitment. Sold individually. Left or right side fitment.
$47.30
Make a selection 91163193301EQ This is the inner headlight ring that retains the adjustment and securing screws. This part is "resi-coated" and includes all mounting hardware. Sold individually. Driver's and passenger's side fitment. 2 necessary per car.
$93.50
Make a selection 91142314700 This ball socket is responsible for kick down; it tends to wear out with time causing delayed response and lackluster throttle response. It is a simple replacement and is very rewarding when adjusted correctly. One is on the end of the throttle cable and the other behind the pedal. We also recommend adding 2 x securing clips for installation, part # sold individually. 4 necessary per car. View/Change Diagram
From $8.00
Make a selection 91163114100 This outer headlight ring is primed and ready for paint. Be sure to add a new securing screw, part # 91163113200, headlight seal, part # 91163111502 and washer, part # 113951539 for a complete installation. Sold individually. Driver's and passenger's side fitment. 2 necessary per car. General Fitment911 1987-89
From $49.50
Make a selection 91153170202 As a striker plate ages, it will start to rattle and can potentially be a safety risk. We recommend securing them with new oval head screws, part # 99921900800. 2 screws are needed per plate. We also recommend adding new striker plates gaskets, either 90153170323 or 90153170324 depending on what thickness you need. This line is a high-quality replacement part, sourced in Germany and designed to perform like the original. Sold individually. 1 necessary per car.
From $133.10
Make a selection 91163114100CH This outer headlight ring is made in chrome and is a quality replacement part manufactured by dansk. They offer a complete line of replacement parts to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. This commitment has made dansk one of the original equipment manufacturers (oem) to Porsche in Germany. Be sure to add a new securing screw, part # 91163113200, headlight seal, part # 91163111502 and washer, part # 113951539 for a complete installation. Sold individually. Driver's or passenger's side fitment. 2 necessary per car.
$58.30
Make a selection 91163193300EQ This is the inner headlight ring that retains the adjustment and securing screws. This part is "resi-coated" and includes all mounting hardware. Sold individually. Driver's or passenger's side fitment. 2 necessary per car.
$93.50
Make a selection 91153170102 As a striker plate ages, it will start to rattle and can potentially be a safety risk. We recommend securing them with new oval head screws, part # 99921900800. 2 screws are needed per plate. We also recommend adding new striker plates gaskets, either 90153170323 or 90153170324 depending on what thickness you need. This line is a high-quality replacement part, sourced in Germany and designed to perform like the original. Sold individually. 1 necessary per car.
From $82.50
Make a selection 91153163100 This is the smaller base gasket for the door handle. When replacing this gasket, we recommend replacing the exterior large door handle gasket, part # 91153163200 and the securing nuts, part # 900 910 008 02 and washers, part # 900 025 003 02. Sold individually. Driver or passenger side fitment. View/Change Diagram
From $5.50
Make a selection FVD559213 Includes the later model (series iii from 2009) water cooled crest, gasket and emblem securing nuts. Size: 67 mm x 51 mm sold individually. 1 is necessary per car.
$226.72
Make a selection FVD559211 Includes the early model (series i) air cooled crest, gasket and emblem securing nuts. Size: 67 mm x 51 mm sold individually. 1 is necessary per car.
$225.23
Make a selection 99959191640 These plastic clips can break free of the securing grommets 99970216040 and allow your side skirts to become loose. Be sure to replace them as needed. If you repaint or restore the car they are mandatory. Sold individually. 12 necessary per car. View/Change Diagram
From $3.00
Make a selection FVD504399A Includes everything needed to install a set of 4 GT2 / rsr fender flares. Includes: 2 x rubber trim (piping) approx. 8 m (26 feet) 32 x factory style securing screws. 32 x factory style nuts. General Fitment911 1994-98
From $119.90
Make a selection FVD559212 Includes the later model (series ii from 996) water cooled crest, gasket and emblem securing nuts. Size: 67 mm x 51 mm sold individually. 1 is necessary per car.
$214.78
Make a selection 99635195901 One required with each caliper. View/Change Diagram
From $23.71
Make a selection FVD721T248 This special service tool was developed for the crucial task of securing the intake and exhaust camshafts in relation to each other during base timing, etc. Trying to do this task with any other method is risking a total engine failure. Applicable: Porsche model - 996 3.4 and 986
$223.30
Make a selection FVD721T44 Pulley wrench. Needed for securing the generator from rotating during r&r of pulley or fan belt. Applicable: model - 911, year 1965-1974.
$49.50
Make a selection 94435195202 Contains: (qty.) (4) retaining pins (2) spring clips (4) securing clips (2) retaining springs
From $30.00
Make a selection PCG53106000EQ Door handles fade over time and the lock mechanisms can fail. If you are restoring or repainting your classic it is a perfect time to replace your door handles. Includes the lock mechanism (without stipulated lock number) and 4 new keys. This is an aftermarket part made by dansk, they offer a complete line of replacement bodywork to complement the entire Porsche model range. All dansk products are manufactured to European standards to ensure the quality that you expect for your Porsche. This commitment has made dansk one of the original equipment suppliers to the Porsche in Germany. We recommend replacing the gaskets as well, small door handle gasket, part # 91153163100 and large door handle gasket, part # 9115...(choose a part on the right to read more)
$561.00
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |