Vehicles
3 not categorized PORSCHE 964 ENGINE STANDCan't find what you need? Try browsing the Accessories or Exploded Diagrams!
FVD721T31D Only for the aircooled cars.
$768.90
Make a selection FVD375003 Are you experiencing vibrations in the cabin? The most likely cause is a worn transmission mount. Severely worn mounts translate to engine component wear and can even cause difficulty shifting. Our mount is manufactured in europe by an OEM supplier using the finest materials. It is a 65 shore rubber hardness value which is the same as the what was standard on these cars. Be sure to swap yours out during your next service. Sold individually. Central fitment in transmission carrier 96437502301. 1 qty. Required. Tech tip: now is the time to replace the old hardware as well. Below is a list of what is needed for installation. 1 qty. Hex head bolt m10x100 90007429202 1 qty. Lock nut m10 49020001 2 qty. Washers 10.3x...(choose a part on the right to read more)
$165.00
Make a selection BES96400100S FVD "brombacher" sound version exhaust system for 964 89-94 General Fitment911 1989-94
$7,854.00
Make a selection BES96410100S FVD "brombacher" sound version exhaust system for 964 89-94 General Fitment911 1989-94
$8,518.40
Make a selection M0507R Removing the blower motor assembly from your 1989-98 964/993 is a very standard modification for cars that want to loose a few pounds. This modification reduces your cars weight by about 10 pounds and really cleans up the engine bay. This kit is an exact replica as used by Porsche motorsports for the factory lightweight 964 cup and 964 rsr race cars. Manufactured from aluminum and is available in red and black powder coat or clear anodized. Comes with all the stainless steel hardware required for a 20 minute installation. Will not work on turbo cars. Red in color. General Fitment911 1989-94911 1994-98
$115.50
Make a selection BES96402000S "brombacher" catalytic bypass pipe for 964 89-94 General Fitment911 1987-89
$226.60
Make a selection M0507 Removing the blower motor assembly from your 1989-98 964/993 is a very standard modification for cars that want to loose a few pounds. This modification reduces your cars weight by about 10 pounds and really cleans up the engine bay. This kit is an exact replica as used by Porsche motorsports for the factory lightweight 964 cup and 964 rsr race cars. Manufactured from aluminum and is available in red and black powder coat or clear anodized. Comes with all the stainless steel hardware required for a 20 minute installation. Will not work on turbo cars. Silver in color. General Fitment911 1989-94911 1994-98
$115.50
Make a selection RES96400000S FVD "brombacher" sound version exhaust system for 964 89-94 General Fitment911 1989-94
From $5,810.20
Make a selection M0507B Removing the blower motor assembly from your 1989-98 964/993 is a very standard modification for cars that want to loose a few pounds. This modification reduces your cars weight by about 10 pounds and really cleans up the engine bay. This kit is an exact replica as used by Porsche motorsports for the factory lightweight 964 cup and 964 rsr race cars. Manufactured from aluminum and is available in red and black powder coat or clear anodized. Comes with all the stainless steel hardware required for a 20 minute installation. Will not work on turbo cars. Black in color. General Fitment911 1989-94911 1994-98
$115.50
Make a selection RES96400100S FVD "brombacher" sound version exhaust system for 964 89-94 General Fitment911 1989-94
From $7,496.50
Make a selection 96411691101 Eliminate your clutches slipping and chattering with this genuine kit. We only recommend this kit for non-modified cars that are not running any aftermarket upgrades like exhaust, chip tuning or larger displacements, etc. Complete kit consists of: 1 qty. Clutch disc 1 qty. Pressure plate 1 qty. Release bearing 1 qty. Spline lubricant kit weighs 14.1 lbs. (6.4 kg) tech tip: when you are planning to install a new clutch, it is a good idea to replace the clutch release fork and shaft to ensure proper clutch engagement. Our part # FVD116999 we also recommend a new guide tube 95011681306 for proper installation. View/Change Diagram
From $768.04
Make a selection 846R1960 Brey-krause?s b-pillar brace system adds structural support and body rigidity to your vehicle using a multiphase design. Each component serves a functional purpose as a stand-alone product while coupling to form a complete assembly, delivering ultimate chassis stiffening performance for ?74-?98 Porsche 911 coupes. These products are made from airplane-grade aluminum and high-quality stainless steel. Superior engineering design enables easy installation and removal while utilizing existing factory mounting points. General Fitment911 1994-98911 1989-94 911 1970-73
$409.16
Make a selection 96411691102 Eliminate your clutches slipping and chattering with this genuine kit. We only recommend this kit for non-modified cars that are not running any aftermarket upgrades like exhaust, chip tuning or larger displacements, etc. Complete kit consists of: 1 qty. Clutch disc 1 qty. Pressure plate 1 qty. Release bearing 1 qty. Spline lubricant kit weighs 13.4 lbs. (6.1 kg) tech tip: when you are planning to install a new clutch, it is a good idea to replace the clutch release fork and shaft to ensure proper clutch engagement. Our part # FVD116999 we also recommend a new guide tube 95011681306 for proper installation. Please note: only for 1989 964 owners! This kit cannot be used on the 1989 964's that used the earlier v...(choose a part on the right to read more) View/Change Diagram
From $768.04
Make a selection E2290 K&N filters – treat your car with the best breath possible. These high quality filters improve performance, while saving you money. Providing additional power through its unique design, these filters replace the standard filter element and are very low restriction, so they improve engine breathing. Because they allow more air into your engine, the result is more power along with improved fuel economy. You’ll never buy another filter for your vehicle once you install the K&N. When the filter does become dirty, simply take it out and wash it, re-oil it and use it again. Each K&N filter comes with a one million mile warranty. Our recharger kit will allow you to remove and clean your filter 3 times! Photo shows...(choose a part on the right to read more) General Fitment356 1950-59356 1960-65
$44.95
Make a selection 64436103111 356a & b super hubcap. this hubcap was standard equipment on all models with super and super 90 engines and optional on all other models. The center crest is gold-plated with fired enamel colors. Fits all drum brakes wheels. View/Change Diagram
$165.00
Make a selection FVD10397591 The h11 bolt (wmc7 and wmc6) is a high quality, aircraft standard fastener. Under racing conditions, we suggest that the h11 bolts be changed periodically. General Fitment944 1982-85944 1985-88 944 1989-91 911 TURBO/GT2 2001-05 911 1994-98 968 1992-95 911 1989-94 911 1987-89 911 1984-86 911 1978-83 930 1975-77 911 1974-77 911 1970-73 911 1965-69
$29.70
Make a selection FVDIDA5001 The pmo carburetor was designed from the beginning to be a state-of-the art carburetor. Pmo start off with a casting designed around a 50mm throttle plate and downsized to 46 and 40mm to achieve three different sizes. This compares favorably with conventional carburetors, including weber. General Fitment911 1978-83911 1984-86 911 1987-89 911 1989-94 911 1994-98
$4,400.00
Make a selection FVDIDA50 Complete carburetion kits ! General Fitment911 1974-77911 1978-83 911 1984-86 911 1987-89 911 1989-94 911 1994-98
$10,902.10
Make a selection NLA08801 K&N filters – treat your car with the best breath possible. These high quality filters improve performance, while saving you money. Providing additional power through its unique design, these filters replace the standard filter element and are very low restriction, so they improve engine breathing. Because they allow more air into your engine, the result is more power along with improved fuel economy. You’ll never buy another filter for your vehicle once you install the K&N. When the filter does become dirty, simply take it out and wash it, re-oil it and use it again. Each K&N filter comes with a one million mile warranty. General Fitment356 1950-59356 1960-65
$48.39
Make a selection STP2000 This professional-grade engine stand is designed to bolt up to every Porsche and vw air-cooled boxer engine ever produces, from type 1 to the 3.6l. When working on your engine out of the car, don't risk damage to your block; get the engine stand professionals use. Includes the engine holding fixture, heavy duty bench clamp, and flywheel lock. General Fitment356 1950-59356 1960-65 912 1965-69 914 1970-76 911 1965-69 911 1994-98 911 1989-94 911 1987-89 911 1984-86 911 1978-83 930 1975-77 911 1974-77 911 1970-73
$664.95
Make a selection FVD211343 Already replaced your heater blower tube with a carbon bypass? This carbon / kevlar air duct will match the engine decor perfectly. It is a replica of the factory rs lightweight factory air duct. This is a quality tuning product manufactured by dansk. They offer a complete line of tuning and performance parts to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. This commitment has made dansk one of the original equipment manufacturers (oem) to Porsche in Germany. This installs easily and really dresses up the engine. Sold individually. 1 necessary per car.
$267.30
Make a selection T55201300 Engine stand adapter. For mounting 356 engines on a u.s. Spec engine stand with 4 arm head. General Fitment356 1950-59356 1960-65
$308.39
Make a selection
© 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |