Vehicles
1 not categorized PORSCHE 964 F MODEL BUMPERCan't find what you need? Try browsing the Accessories or Exploded Diagrams!
91163162004 Perfect as a replacement or when you are upgrading your 964-rear center bumper section to the rs / turbo 3.6 spec. Includes gasket and bulb. The 964 / 965 FVD rear rs / turbo 3.6 l center section is part # FVD505123964rs for the 911 and 914, please check the models tab to make sure that this fits your car. Sold individually. 2 necessary per car. View/Change Diagram
From $26.10
Make a selection 99350501900 This support assists in absorbing impacts and supports the bumper reinforcement bars. High-quality OEM (original equipment manufacturer) replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 2 necessary per bumper. Please note: this fits the front bumper for the 928 models listed on the model fitment tab. It fits the front bumper for the 964 / 965 models and fits the rear bumper of the 993 models listed on the model fitment tab. View/Change Diagram
From $31.90
Make a selection FVD512964008RSK Made in europe by one of the manufacturers to Porsche. Extremely high-quality kevlar / carbon rear bumper that includes every detail for a perfect fit. Features: - produced by an OEM manufacturer. - highest quality standards. - perfect fitment. - lightweight 4 kg (8.81 lbs) - kevlar / carbon - mounting is just like factory, no modifications are necessary. - fits all 964 narrow body models - left and right side exits for exhaust please note: these are high quality parts that take time to manufacture and cure properly. Lead times can vary anywhere from 15-30 days depending on where you are in the world. If you do not have the rs license plate light please also order 91163162004 General Fitment911 1989-94
From $1,791.90
Make a selection FVD50501900 When you are installing a lightweight bumper or bumper bar for racing use, you want to remove as much weight as possible. Don't forget to remove your heavy factory supports. These are a lightweight alternative and are made in Germany. Weighs: .3 kilograms ( .33 lbs ) sold individually. 2 needed for the rear or front bumper. Measurements shown are in centimeters. Please note: these fit the 928 87-91 front bumper, 964 / 965 89-94 front bumper, 993 94-98 rear bumper. Please check the model fitment tab to ensure accurate fitment. General Fitment911 GT3 2003-05911 TURBO/GT2 2001-05 911 1998-05
From $141.90
Make a selection FVD512964008RS Made in europe by one of the manufacturers to Porsche. Extremely high-quality glass fiber komposite (gfk) rear bumper that includes every detail for a perfect fit. Features: - produced by an OEM manufacturer. - highest quality standards. - perfect fitment. - lightweight - glass fiber komposite (gfk) - mounting is just like factory, no modifications are necessary. - fits all 964 narrow body models - left and right side exits for exhaust please note: these are high quality parts that take time to manufacture and cure properly. Lead times can vary anywhere from 15-30 days depending on where you are in the world. If you do not have the rs license plate light please also order 91163162004 General Fitment911 1989-94
From $1,306.37
Make a selection RES96400100S1 More low and mid-range torque than our race system with cat bypass. Larger primaries, larger collector, largest diameter tubing on the market. Made for mid-range and top end performance with the added beauty of dual exhaust tips! + 25 hp & + 23 torque - 100 cell hjs tri-metallic race catalytics. -2 1/2 tubing (63.5mm) for max. Power across the rpm range.* -weighs 49 lbs. (22 kg). -German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - aeroquip cone style catalytic connection design to prevent exhaust leaks. -includes aeroquip quick release clamps. -made in Germany by m&m exhaust, gmbh. -dual round 3 exhaust tips -intoxicating flat 6 growl at idle, partial throttle and wide open throttle. P...(choose a part on the right to read more)
$7,403.00
Make a selection 64450524705 On 356b/c models the rear bumper ends are bolted through the body into the fender brace. This support plate backs up against the body on the inside. One piece is required on each side. View/Change Diagram
From $6.16
Make a selection 64450524305 This spacer tube is installed at each end of the rear bumper on 356b/c models. The bolt from the fender bracket goes through the spacer and into the end of the bumper. View/Change Diagram
From $9.24
Make a selection FVD500964RSRGT Motorsport quality grp (glass-reinforced plastic) complete body kit. Includes rsr (adac GT class) specifications complete body kit with front bumper (with retractable spoiler lip), front and rear fender flares, side skirts and the matching rear bumper. Features: - produced by a German motorsport manufacturer. - strength testing is available - made of high strength, grp (glass-reinforced plastic) sold individually. 1 necessary per car. Please note: please provide us with the year / model. These are motorsport quality parts that take time to manufacture and cure properly. Lead times can vary anywhere from 15-30 days depending on where you are in the world. All grp products must properly be fitted and completely p...(choose a part on the right to read more) General Fitment911 1989-94
$7,636.20
Make a selection 64450530315 Excellent reproduction of the original left rear bumper guard for all 60-65 356 models. price blows away the cost of rechroming yours! View/Change Diagram
From $153.00
Make a selection
© 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |