PORSCHE 997 NEW ENGINES
Can't find what you need? Try browsing the Accessories or Exploded Diagrams!<-- Try narrowing by car using the menu to the left.
Engine ducting seal. Two pieces required. One piece for engine-to-body cover plate, and one another piece for two side cover plates. For 1500gs Carrera & Carrera 2, use two of these seals.
View/Change Diagram
From $40.61
Make a selection
Known as: bonnet
View/Change Diagram
From $287.50
Make a selection
An interesting fact: did you know the factory thermostat doesn't start to even open until 186.8f and doesn't fully open until almost 210f? did you also know that the new '09 dfi engines run a 176f thermostat? Or how about factory turbo, GT2, and GT3 engines that run with even colder thermostats from the factory? This low temperature thermostat, featuring a calibrated, German-made 160f thermostat pre-installed in a new, oe wahler thermostat housing and gasket, is calibrated to allow thermostat opening a full 20-25f degrees earlier than the factory thermostat. That means that the the low temperature thermostat is designed to be fully open by 180-185f, allowing for full flow to the cooling system to maximize c...(choose a part on the right to read more)
General Fitment BOXSTER 1997-04 BOXSTER 2005-08 911 1998-05 911 2005-08 CAYMAN 2006-08
There are not many warning signs of an impending ims failure short of a “death rattle” that occurs as the bearing fails and comes apart. These kits replace the factory sealed bearing with a new, severe duty custom ceramic hybrid roller ball bearing for reduced friction and superior performance in poorly lubricated operating conditions and replaces the factory ims flange hub, bearing support, and fastener with a stronger, revised billet chromoly assembly. The center bearing support also receives an increase in size and no longer is cut for the o-ring that keep engine oil from leaking out of the engine - we have relocated the o-ring to the ims hub flange for added strength to the center stud & bearing support...(choose a part on the right to read more)
General Fitment BOXSTER 2005-08 BOXSTER 1997-04 911 1998-05
"brombacher" exhaust system for 997 GT3/rs
Facts:
- + 25 crank hp & + 25 crank torque
- 200 cell high flow, tri metal German hjs sport catalysts
- 2 3/4" tubing (70 mm) straight through design for max. Power
- equal length header set up for maximum torque gain
- weighs 71 lbs. (32,2 kg),
- 15.5 lb (7 kg) weight savings over stock
- t 316 stainless steel for improved durability over t 304
- includes all necessary clamps and mounting brackets
- 2 x 3.5"(90mm) round center exit tips
- made in Germany
- intoxicating growl at idle, partial throttle and wide open throttle
- no dme programming necessary
FVD is proud to introduce our newest line of Brombacherexhaust systems. Brombacher exhausts...(choose a part on the right to read more)
General Fitment 911 GT3 2007-11
$8,507.40
Make a selection
Brombacher 997 tt stainless steel race pipes
Facts:
- + 35 crank hp & + 25 crank torque
- 3" tubing (75mm) that tapers down to 2.25" (57mm) to prevent turbo damage.
- weighs 7 lbs. (3,1 kg)
- t 316 stainless steel for improved durability over t 304.
- bolts up to the turbochargers, replacing both the cats and the muffler.
- reduces turbo lag and backpressure.
- exhaust tips are not included! Stock tips will fit.
- intoxicating growl at idle, partial throttle and wide open throttle.
- made in Germany
- programming or o2 sensor simulators are necessary, as the lack of catalytic converters will throw the check engine light. (see part numbers below)
Figures:
Genuine:
Engine - 6 cylinder...(choose a part on the right to read more)
General Fitment 911 TURBO/GT2 2007-09
From $456.50
Make a selection
Loud, low, deep tones with exaggerated turbo whistling and sinister gurgling and crackling off throttle. By far the best sound you can get out of your turbo, not to mention being able to shoot flames! The only real drawback is the drone in the cabin which we try to minimalize by stepping down the diameter in 3 stages. - + 35 crank hp & + 25 crank torque - 3 tubing (75mm) that tapers down to 2.25" (57mm) to prevent turbo damage. - weighs 7 lbs. (3,1 kg) - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - bolts up to the turbochargers, replacing both the cats and the muffler. - reduces turbo lag and backpressure. - exhaust tips are not included! Stock tips will fit. - intoxicating grow...(choose a part on the right to read more)
General Fitment 911 TURBO/GT2 2007-09
From $444.40
Make a selection
There are not many warning signs of an impending ims failure short of a “death rattle” that occurs as the bearing fails and comes apart. These kits replace the factory sealed bearing with a new, severe duty custom ceramic hybrid roller ball bearing for reduced friction and superior performance in poorly lubricated operating conditions and replaces the factory ims flange hub, bearing support, and fastener with a stronger, revised billet chromoly assembly. The center bearing support also receives an increase in size and no longer is cut for the o-ring that keep engine oil from leaking out of the engine - we have relocated the o-ring to the ims hub flange for added strength to the center stud & bearing support...(choose a part on the right to read more)
General Fitment BOXSTER 2005-08 BOXSTER 1997-04 911 1998-05 911 1987-89
Brombacher racing exhaust system for 997gt3/rs with 90mm x 2 round tips
Facts:
- + 25 crank hp & + 25 crank torque
- catalytic bypass
- 2 3/4" tubing (70 mm) straight through design for max. Power
- equal length header set up with merge collector for maximum torque gain
- weighs 42 lbs. (23 kg)
- 44.5 lb (19 kg) savings over stock system!
- t 316 stainless steel for improved durability over t 304
- includes all necessary clamps and mounting brakets
- made in Germany
- 108 db
- intoxicating growl at idle, partial throttle and wide open throttle
- dme programming necessary.
The FVD GT3 race exhaust gives the 997 GT3 a more pronounced, aggressive sound similar to the 997 cup car. Our exhaust ...(choose a part on the right to read more)
General Fitment 911 GT3 2007-11
From $4,331.80
Make a selection
Do your Porsche composite headlights look dull and yellow? Do you want the crystal-clear look again, but don't want to buy new and expensive headlights? The new sylvania headlight restoration kit is for you. New plastic headlight lenses have a factory applied uv coating to protect the plastic from degradation. over time, harsh uv rays and road debris penetrate the factory uv coating resulting in hazing and yellowing. this hazing is not only unsightly, it is a serious safety concern, in fact hazed lenses reduce downroad illumination by 65% and increases oncoming driver glare by scattering light upward.
Unlike other lens restoration products designed just to remove the haze and yellowing, the sylvania head...(choose a part on the right to read more)
General Fitment 911 GT3 2007-11 911 2005-08 911 GT3 2003-05 911 TURBO/GT2 2001-05 CAYENNE 2007-10 CAYENNE 2003-06 CAYMAN 2006-08 BOXSTER 2005-08 BOXSTER 1997-04
Brombacher 986/s (TUV) stainless steel sport muffler
Facts:
- + 8 crank hp & + 10 crank torque
- 2 1/4" tubing (55 mm) straight through design for max. Power
- weighs 23 lbs. (10,4 kg)
- t 316 stainless steel for improved durability over t 304
- dual 3.5"(90mm) round tips
- made in Germany
- intoxicating growl at idle, partial throttle and wide open throttle while remaining within the db limits of the TUV.
- no dme programming necessary.
- ask for the mounting kit FVD mk 986 001wich includes all gaskets and clambs.
FVD is proud to introduce our newest line of Brombacherexhaust systems. Brombacher exhausts are engineered for the discerning Porsche owner and offer unmatched performance, unparall...(choose a part on the right to read more)
General Fitment BOXSTER 1997-04
$2,068.00
Make a selection
Brombacher racing exhaust system for 997gt3/rs
Facts:
- + 25 crank hp & + 25 crank torque
- bypass-catalytics
- 2 3/4" tubing (70 mm) straight through design for max. Power
- equal length header set up with merge collector for maximum torque gain
- weighs 42 lbs. (19 kg)
- 44.5 lb (20 kg) saving?s over stock system!
- t 316 stainless steel for improved durability over t 304
- reuse?s factory center muffler for backpressure and resonance dampening.
- includes all necessary clamps and mounting brakets
- made in Germany
- 106 db
- intoxicating growl at idle, partial throttle and wide open throttle
- reuse?s factory tips or larger aftermarket tips
- dme programming necessary 2nd gen
The FVD...(choose a part on the right to read more)
General Fitment 911 GT3 2007-11
From $3,177.67
Make a selection
Brombacher racing exhaust system for 997gt3/rs with 90mm x 2 round tips
Facts:
- + 25 crank hp & + 25 crank torque
- 200 cell high flow, tri metal German hjs sport catalysts
- 2 3/4" tubing (70 mm) straight through design for max. Power
- equal length header set up with merge collector for maximum torque gain
- weighs 42 lbs. (23 kg)
- 44.5 lb (19 kg) savings over stock system!
- t 316 stainless steel for improved durability over t 304
- includes all necessary clamps and mounting brakets
- made in Germany
- 108 db
- intoxicating growl at idle, partial throttle and wide open throttle
- dme programming necessary on 997.2 GT3
The FVD GT3 race exhaust gives the 997 GT3 a more pronounced, aggre...(choose a part on the right to read more)
General Fitment 911 GT3 2007-11
From $6,698.73
Make a selection
Highlights:
Superb daily driver, OEM replacement, r90 type approved pad.
Features red ?brake in? Surface coating for instant safe braking after install.
New 100 % eco friendly material with zero sulphides.
No shims for noise reduction needed.
More bite from cold.
Works in hot and dry climates as well as in cold.
Fully r 90 approved.
If you simply need a quality OEM replacement pad, look no further than the blackstuff brake pad. It is a highly engineered brake compound that lasts longer, produces minimal dust and is the perfect choice for the urban or daily driver. Why spend more if all you need is a quality replacement pad?
The blackstuff brake pad is a total non metallic pad containing zero stee...(choose a part on the right to read more)
General Fitment 911 GT3 2003-05 911 1994-98 911 1989-94 928 1992-95
"brombacher" sport muffler for 997gt3/rs (sound version)
Facts:
- + 10 crank hp & + 10 crank torque
- 2 3/4" tubing (70mm) straight through design for max. Power
- weighs 28 lbs. (12.7 kg)
- replaces stock side mufflers and stock center muffler
- 36 lbs (16.3 kg) savings over stock system!
- t 316 stainless steel for improved durability over t 304
- 2 x 3.5"(90mm) round tips
- includes all necessary clamps and mounting brackets
- made in Germany
- 105 db
- intoxicating cup car growl at idle, partial throttle and wide open throttle
- no interior resonance
- no dme programming necessary, does not alter emissions, 50 state legal in the u.s.
For reference:
997 GT3 OEM exhaust weight
Stock...(choose a part on the right to read more)
General Fitment 911 GT3 2007-11
$3,128.40
Make a selection
"brombacher" exhaust system for 997 GT3/rs (sound version) with rsr style tips
Facts:
- + 25 crank hp & + 25 crank torque
- 200 cell high flow, tri metal German hjs sport catalysts
- 2 3/4" tubing (70 mm) straight through design for max. Power
- equal length header set up with merge collector for maximum torque gain
- weighs 71 lbs. (32,2 kg)
- 15.5 lb (7 kg) weight savings over stock
- t 316 stainless steel for improved durability over t 304
- includes all necessary clamps and mounting brackets
- 2 x 2 3/4" (70mm) angle cut rsr center exit tips
- made in Germany
- 98 db (98db at idle and partial throttle, builds to 100db at wot)
- intoxicating growl at idle, partial throttle and wide open ...(choose a part on the right to read more)
General Fitment 911 GT3 2007-11
$8,507.40
Make a selection
Brombacher race exhaust system for 997 GT3/rs (super sound) with rsr style tips & center muffler adapters to run stock center muffler.
Facts:
- + 25 crank hp & + 25 crank torque with use of stock center muffler.
- 200 cell high flow, tri metal German hjs sport catalysts
- 2 3/4" tubing (90 mm) straight through design for max. Power
- equal length header set up with merge collector for maximum torque gain
- weighs 34.7 lbs. (15.7 kg) this is the lightest stainless system in the Brombacherline !**
- 51.8 lb (23.5 kg) savings over stock system!**
- t 316 stainless steel for improved durability over t 304
- includes all necessary clamps and mounting brackets
- bypass' center muffler with straight p...(choose a part on the right to read more)
General Fitment 911 GT3 2007-11
$4,978.60
Make a selection
Brombacher racing exhaust system for 997gt3/rs
Facts:
- + 25 crank hp & + 25 crank torque
- 200 cell high flow, tri metal German hjs sport catalysts
- 2 3/4" tubing (70 mm) straight through design for max. Power
- equal length header set up with merge collector for maximum torque gain
- weighs 42 lbs. (23 kg)
- 44.5 lb (19 kg) savings over stock system!
- t 316 stainless steel for improved durability over t 304
- includes all necessary clamps and mounting brakets
- made in Germany
- 108 db
- intoxicating growl at idle, partial throttle and wide open throttle
- no dme programming necessary
The FVD GT3 race exhaust gives the 997 GT3 a more pronounced, aggressive sound similar to the 997 cup c...(choose a part on the right to read more)
General Fitment 911 GT3 2007-11
$6,996.00
Make a selection
"brombacher" racing exhaust system for 997gt3/rs
Facts:
- + 25 crank hp & + 25 crank torque
- 200 cell high flow, tri metal German hjs sport catalysts
- 2 3/4" tubing (70 mm) straight through design for max. Power
- equal length header set up with merge collector for maximum torque gain
- weights 6 kg
- 33 kg savings over stock system!
- t 316 stainless steel for improved durability over t 304
- reuse?s factory center muffler for backpressure and resonance dampening.
- includes all necessary clamps and mounting brakets
- made in Germany
- 108 db
- intoxicating growl at idle, partial throttle and wide open throttle
- reuse?s factory tips or larger aftermarket tips
- no dme programming neces...(choose a part on the right to read more)
General Fitment 911 GT3 2007-11
$11,661.10
Make a selection
- + 25 crank hp & + 25 crank torque
- 200 cell high flow, tri metal German hjs sport catalysts
- 2 3/4" tubing (70 mm) straight through design for max. Power
- 1,000 degree celcius titanium
- equal length header set up for maximum torque gain
- weighs 48 lbs. (21,9 kg),
- 38.5 lb (17,5 kg) weight savings over stock
- includes all necessary clamps and mounting brackets
- 2 x 3.5"(90mm) blue flamed titanium center exit tips
- made in Germany
- 98 db (98db at idle and partial throttle, builds to 100db at wot)
- intoxicating growl at idle, partial throttle and wide open throttle
- no dme programming necessary
FVD is proud to introduce our newest line of Brombacherexhaust systems. Brombacher exhaus...(choose a part on the right to read more)
General Fitment 911 GT3 2007-11
$16,528.60
Make a selection
Back pressure is extremely reduced trough specific guidance and piping in the exhaust muffler.
- 200 hd cell high flow, tri metal German hjs sport catalysts
- weighs 39 lbs. (18,1 kg)
- t 316 stainless steel for improved durability over t 304
- cone style catalytic connection design to prevent exhaust leaks
- includes quick release clamps
- made in Germany
- dme programming necessary.
We use the latest hjs cats, they are nicknamed ?hd? For high durability matrix design catalytic converters. They have a sm-matrix (winding of three flat and corrugated foils) and a special connection to the matrix sheath, which equates to extremely high durability for track and street use. The added benefit is that ...(choose a part on the right to read more)
General Fitment 911 TURBO/GT2 2007-09
From $5,815.70
Make a selection
With the success of our ypipe kit on the 996tt and 997tt, we did a hybrid and built this new part to work with the OEM intake on the 997.2 turbo. Airflow restrictions can always hamper performance and power and this part like any other does that as well. Our ypipe kit has smooth mandrel 3inch bends from a 4inch collector that goes to the throttlebody. For fitment reasons, we then neck down to 2.25inches to fit on the stock boost hoses. We have incorporated all fittings/sensors that are required.
Going off our original baseline using our mustang awd on 91octane and about 90f temp, the car made 455awhp and 443ft/lbs of torque. We did these test in standard mode, not sport to see the linear gains. With the addi...(choose a part on the right to read more)
General Fitment 911 TURBO/GT2 2010-13
$1,199.95
Make a selection
"brombacher" titanium race system (sound version) for GT3/rs
Facts:
- + 20 crank hp & + 19 crank torque.
- complete system in titanium (without sidemufflers)
- 200 cell high flow, titanium tri metal German hjs sport catalysts
- 2 x 90mm tailpipes.
- weighs 28.6 lbs (13kg)!
- 1000 degree celcius, high grade titanium material
- 105-107 db
- includes quick release clamps
- made in Germany
- modular design for 100 cell, 200 cell or bypass use
- intoxicating growl at idle, partial throttle and wide open throttle
- no dme programming necessary.
The titanium tips can be ordered ?flamed? Which exhibit?s the blue tint.
All titanium systems not created equal! Brombacher exhausts systems are nearl...(choose a part on the right to read more)
General Fitment 911 GT3 2007-11
$13,066.90
Make a selection
"brombacher" sport muffler for 997gt3/rs (sound version) in titanium
Facts:
- + 10 crank hp & + 10 crank torque
- 2 3/4" tubing (70mm) straight through design for max. Power
- weighs 17 lbs. (7.7 kg)
- replaces stock side mufflers and stock center muffler
- 47 lbs (21.3 kg) savings over stock system!
- 1,000 degree celcius titanium
- 2 x 3.5"(90mm) round tips
- includes all necessary clamps and mounting brackets
- made in Germany
- 105 db
- intoxicating cup car growl at idle, partial throttle and wide open throttle
- no dme programming necessary, does not alter emissions, 50 state legal in the u.s.
All titanium systems are not created equal. The titanium that we use is the highest grade ...(choose a part on the right to read more)
General Fitment 911 GT3 2007-11
$6,107.20
Make a selection
+650hp 997 tt (sound version) stainless steel exhaust system
The +650 hp FVD sport exhaust system is specially designed for vehicles with performance increases of more than 485kw (650ps). Back pressure is extremely reduced trough specific guidance and piping in the exhaust muffler.
- 200 hd cell high flow, tri metal German hjs sport catalysts
- 2 3/4" tubing (70mm) straight through design for max. Power
- weighs 39 lbs. (18,1 kg)
- t 316 stainless steel for improved durability over t 304
- cone style catalytic connection design to prevent exhaust leaks
- includes quick release clamps
- made in Germany
- dme programming necessary.
We use the latest hjs cats, they are nicknamed ?hd? For high d...(choose a part on the right to read more)
General Fitment 911 TURBO/GT2 2007-09
$5,864.23
Make a selection
© 2024 Automobile Atlanta Inc.
505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844
|