Vehicles
10 not categorized PORSCHE CAYENNE TURBO SEAL KITSCan't find what you need? Try browsing the Accessories or Exploded Diagrams!100103038TU997 Mahle 3.8 liter piston and cylinder conversion kit for 996/997 turbo / GT2 & GT2 rs - increased horsepower and torque.* - forged pistons with deeper, mirrored valve pockets with 23 mm wrist pin. - slip fit, steel (st52) cylinders. - piston pin bore is off center (deaxiert) for factory quiet operation. - 9.4:1 compression. - 102 mm bore. - piston rings installed directly on the pistons for ease of installation. - made in Germany by mahle gmbh. *please note: horsepower and torque gains depend on the software used, camshafts, crankshaft and other internal modifications. 700+ hp and torque can be achieved with use of these pistons and cylinders with a proper engine build and software. Contact your sales person for ...(choose a part on the right to read more) General Fitment911 TURBO/GT2 2001-05911 TURBO/GT2 2007-09
$14,654.60
Make a selection 99312301452AT Our k-16 remanufactured turbo is cost competitive and is a direct replacement. Simply send us your original k16 turbochargers and a borg warner / kkk certified technician will remanufacture your turbo. The remanufacturing process includes full inspection to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will replace the turbine wheels, thrust bearings, install new seals, recondition the internals and high speed balance the turbo. This ensures reliability and superior performance for many years to come. The remanufacturing is done on an exchange basis only. You must send us your original k16 turbocharger. After receiving y...(choose a part on the right to read more) General Fitment911 1994-98
$2,194.50
Make a selection 100103041TU Mahle 4.1 liter piston and cylinder conversion kit for 996/997 turbo / GT2 & GT2 rs - increased horsepower and torque.* - forged pistons with deeper, mirrored valve pockets. - piston pin bore is off center (deaxiert) for factory quiet operation. - 9.1:1 compression. - 106 mm bore. - piston rings installed directly on the pistons for ease of installation. - made in Germany by mahle gmbh. Water channels and case must be machined to fit. Please add the following to your order: 2 qty. Base gaskets, part # FVD10303905zfd 2 qty. Head gaskets, part # FVD10303905zkd 1 qty. O- ring base set, part # FVD10303905or 1 qty. O- ring head set, part # FVD10303905oro *please note: horsepower and torque gains depend on the softwa...(choose a part on the right to read more) General Fitment911 TURBO/GT2 2007-09911 TURBO/GT2 2001-05
From $8,474.70
Make a selection 99312301352AT Our k-16 remanufactured turbo is cost competitive and is a direct replacement. Simply send us your original k16 turbochargers and a borg warner / kkk certified technician will remanufacture your turbo. The remanufacturing process includes full inspection to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will replace the turbine wheels, thrust bearings, install new seals, install new waste gates, recondition the internals and high speed balance the turbo. This ensures reliability and superior performance for many years to come. The remanufacturing is done on an exchange basis only. You must send us your original k16 turboc...(choose a part on the right to read more) General Fitment911 1994-98
$2,236.30
Make a selection 99312301352ATK Our k-16 remanufactured turbo is cost competitive and is a direct replacement. Simply send us your original k16 turbochargers and a borg warner / kkk certified technician will remanufacture your turbo. The remanufacturing process includes full inspection to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will replace the turbine wheels, thrust bearings, install new seals, install new waste gates, recondition the internals and high speed balance the turbo. This ensures reliability and superior performance for many years to come. The remanufacturing is done on an exchange basis only. You must send us your original k16 turboc...(choose a part on the right to read more)
$2,194.50
Make a selection 99312301452ATK Our k-16 remanufactured turbo is cost competitive and is a direct replacement. Simply send us your original k16 turbochargers and a borg warner / kkk certified technician will remanufacture your turbo. The remanufacturing process includes full inspection to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will replace the turbine wheels, thrust bearings, install new seals, recondition the internals and high speed balance the turbo. This ensures reliability and superior performance for many years to come. The remanufacturing is done on an exchange basis only. You must send us your original k16 turbocharger. After receiving y...(choose a part on the right to read more)
$2,194.50
Make a selection BKPO011841SO Ksport procomp front big brake kit 14 in. Rotor 8 piston caliper Porsche 996 twin turbo 99-04 General Fitment911 1998-05
$2,693.25
Make a selection FVD123013ATK K-16/24 turbo (up to 555 hp) power is focused on low and mid range rpm's. Facts: larger compressor wheel with extended tip. 47.5mm inducer diameter. Cnc modified compressor housing modified and improved back plane uprated staggered gap turbine uprated thrust bearing modified wheel to reduce backpressure balancing of all components factory vacuum unit new bearings and seals all parts are reconditioned and balanced FVD brombachers 993 k-16/24 remanufactured turbos are created for those who are looking for power that is focused in the low and mid rpm range. They are completely bolt on and do not require custom headers or special modifications. The remanufacturing process starts with re-profiling the OEM turbochar...(choose a part on the right to read more)
$2,976.60
Make a selection AP996TT105 Agency power has just given Porsche 996tt owners another way to get an easy 20 bolt-on horsepower with this new big mouth plenum and throttle body kit. agency power set out to engineer and design a plenum that was functional, did not require additional tuning, and simply. Made power! the plenum is 6061 aluminum that retains the same shape as the factory t pipe. the reason to keep a standard t shape is that the engine works off of pulses. just like how Porsche designed, agency power kept this design and simply improved the restriction, the throttle body. the factory throttle body inlet size is 76mm that then jumps up to a 78mm id plastic plenum. General Fitment911 TURBO/GT2 2001-05
$850.95
Make a selection AP9972TT110 Continuing on our modification path for the Porsche 997.2 turbo, agency power has just finished and released their new carbon fiber cold air intake kit. the carbon fiber airbox is a direct replacement for the OEM intake box. the airbox is made using a prepreg process which allows the entire airbox to be flawless from pulls. similar in shape to the OEM box for fitment, this carbon fiber unit features enlarged holes to fit dual K&N cone air filters. the 2x2 weave is finished in a gloss clear coat and sits nicely where the standard plastic box once was. These filters are pressed in through the rear of the intake box utilizing the rubber seal on the filter as a secure fit. General Fitment911 2005-08
$1,500.95
Make a selection AP997TT105 Adding bolt-on horsepower to the 997 turbo is a continuous quest by many enthusiasts looking for more power. reverting back to old tuning technologies, agency power has developed a larger throttle body and plenum kit for the Porsche 997 turbo to gain added performance. the point of a larger throttle body is to get in more air. The more air you bring in, the more power you make. The 997 turbo's engine intake system works off pulses, so how that air is diverted to either side of the engine is not as important as the volume incoming. General Fitment911 2005-08
$850.95
Make a selection BKPO011951SO Ksport procomp front big brake kit 15 in. Rotor 8 piston caliper Porsche 996 twin turbo 99-04 General Fitment911 1998-05
$4,104.00
Make a selection BKPO011961SO Ksport procomp front big brake kit 16 in. Rotor 8 piston caliper Porsche 996 twin turbo 99-04 General Fitment911 1998-05
$4,873.50
Make a selection FSPOR911TIC Product details: General Fitment911 1987-89911 1984-86 911 1978-83 930 1975-77
$2,395.00
Make a selection FVD123013 K-16/24 turbo (up to 555 hp) power is focused on low and mid-range rpm's. Facts: larger compressor wheel with extended tip. 47.5mm inducer diameter. Cnc modified compressor housing modified and improved back plane uprated staggered gap turbine uprated thrust bearing modified wheel to reduce backpressure balancing of all components factory vacuum unit new bearings and seals all parts are reconditioned and balanced FVD Brombacher993 k-16/24 new turbos are created for those who are looking for power that is focused in the low and mid rpm range. They are completely bolt on and do not require custom headers or special modifications. The process starts with re-profiling the OEM turbocharger compressor housing and m...(choose a part on the right to read more)
$2,976.60
Make a selection FVD123013AT K-16/24 turbo (up to 555hp) General Fitment911 1994-98
$2,506.75
Make a selection FVD123014 K-16/24 turbo (up to 555 hp) power is focused on low and mid-range rpm's. Facts: larger compressor wheel with extended tip. 47.5mm inducer diameter. Cnc modified compressor housing modified and improved back plane uprated staggered gap turbine uprated thrust bearing modified wheel to reduce backpressure balancing of all components factory vacuum unit new bearings and seals all parts are reconditioned and balanced FVD Brombacher993 k-16/24 new turbos are created for those who are looking for power that is focused in the low and mid rpm range. They are completely bolt on and do not require custom headers or special modifications. The process starts with re-profiling the OEM turbocharger compressor housing and m...(choose a part on the right to read more)
$2,976.60
Make a selection FVD123014AT K-16/24 turbo (up to 555hp) General Fitment911 1994-98
$2,506.75
Make a selection FVD123014ATK K-16/24 turbo (up to 555hp) power is focused on low and mid range rpm's. Facts: larger compressor wheel with extended tip. 47.5mm inducer diameter. Cnc modified compressor housing modified and improved back plane uprated staggered gap turbine uprated thrust bearing modified wheel to reduce backpressure balancing of all components factory vacuum unit new bearings and seals all parts are reconditioned and balanced FVD brombachers 993 k-16/24 remanufactured turbos are created for those who are looking for power that is focused in the low and mid rpm range. They are completely bolt on and do not require custom headers or special modifications. The remanufacturing process starts with re-profiling the OEM turbocharg...(choose a part on the right to read more)
$2,976.60
Make a selection FVD34791100 Lowering your car without a bump steer kit effectively pulls the steering out of alignment and requires constant steering adjustments that make the car difficult to control. This adjustable bump steer kit will fully compensate to return the steering rack / geometry back to pre-lowered specifications. Our bump steer kit is manufactured to the highest of German standards to ensure the quality, performance and reliability you expect from your Porsche. Features: alloy steel, sealed spherical rod end 14 mm tapered wedge for secure fitment inside the steering arm made for lowering below 30 mm (1.18 inches) / raised spindles allows tie rods to be adjusted downwards no binding throughout suspension travel range finishe...(choose a part on the right to read more) General Fitment911 1970-73
From $284.90
Make a selection FVD500911RSR Made in europe by one of the manufacturers to Porsche. Extremely high-quality grp (glass-reinforced plastic) body kit that includes every detail for a perfect fit. This kit is not motorsports quality, it is OEM quality that sets it apart from the competition. Each part includes all the correct mounting cut outs, pre-drilled holes and fits like an OEM part for a perfect street car appearance. Features: - produced by an OEM manufacturer. - highest quality standards. - perfect fitment. - lightweight - made of high strength, grp (glass-reinforced plastic) kit contains: qty. 1 front bumper with spoiler, part # 10050305502 qty. 1 front bumper mounting kit, part # 10050305502mk qty. 1 rear bumper, part # 10050305503gf...(choose a part on the right to read more) General Fitment911 1970-73
From $9,222.99
Make a selection FVD500964965 This kit contains everything necessary to transform your narrow body c2 or c4 into a 965 wide body / turbo look. It includes motorsport quality glass-reinforced plastic (grp) front + rear bumper and side skirts along with metal fender flares. General Fitment911 1989-94
$7,356.82
Make a selection 10010303000TU Mahle pistons are forged for substantially higher and more uniform strength over pistons that are cast. Mahle cylinders have extremely high thermal resistance and are nikasil coated to reduce wear and friction. We also have the piston rings (sealing and oil scrapers) pre-installed to ensure reliability. Each of our piston and cylinder kits are complete and ready for installation. Features: mahle forged 935 3.0 l turbo pistons mahle nikasil coated cylinders increased 7:1 compression = greater acceleration 95 mm pistons / 95 mm finned wr group 0 cylinders piston rings pre-installed piston pins and circlips are included complete set of 6 - ready for installation made in Germany we recommend the complete engine gas...(choose a part on the right to read more) General Fitment911 1970-73
From $6,197.50
Make a selection 99655921101 This is the original new Porsche hood crest with black "Porsche" lettering. This is the latest design for all of the new models. hood crest kit comes with seal and 2 clips.brass and enamel. View/Change Diagram
From $112.00
Make a selection PK997POINT2 We are proud to offer a wide assortment of OEM Porsche parts. Nobody knows more about your car, then its creators themselves. You dont have to question the build quality, attention to detail, or reliability of these. Why trust anyone else? General Fitment911 2009-12911 TURBO/GT2 2010-13 CAYENNE 2011-14 PANAMERA 2010-14
$43.20
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |