914 Rubber Specials

Don't reinstall weathered and worn rubber seals when replacing your door handles. This is a set of four door seals- two larger main seals and two smaller seal. Made of nylonized rubber, these seals will never shrink or split. This set is a necessity when restoring a car and installing new chrome handles.
Fitment

Long discontinued by the factory, this simple glue in part has by now deteriorated on all 914s and can only be replaced when the windshield is out. A must for any restoration, our profile is much more precise than the other cheap reproduction out there somewhere!
Fitment

Left, right, front, and rear engine bay seals. Cannot get much better and the price is certainly right!
Fitment

Beautiful reproduction! Perfect replacement for the long discontinued factory part, this fits in between the engine lid grill and the painted part of the engine lid acting as a buffer. Easily installed, we include enough for all grilles as well.
Fitment

The best reproduction of this long discontinued factory part, critical to keep the cowl and fender from rusting. Plasticized rubber, exact like the factory originals, and plenty long for a great seal. Beware of the cheap rubber imitations.
Fitment

Never available as a separate item from the factory, this seal fits inbetween the side marker base and the body protecting the paintwork and keeping the water from entering the electrical connection. Nylonized rubber better than the original for long life.
Fitment

Great news! Our brand new reproduction of the lower targa top seal now compliments our upper seal. Made from the highest quality weather strip rubber, original seals are now finally failing at an alarming rate. This seal replaces the old original and dramatically increases top sealing, reduces wind noise, and keeps out the weather! Easily installed in minutes, you will love the improvement.
Fitment

Two great reproduction seals to thoroughly seal the front trunk area once and for all. Set consists of the multiple turn front trunk cavity perimeter seal along with the gas tank bulkhead seal. Easily installed with a bit of weather strip adhesive and the bulkhead seal tapped on with the heal of your hand!
Fitment

Long discontinued by Porsche, these boots allow moisture to drain from the front turn signals. Sold each, two required per car.
Fitment

Discontinued by Porsche. known as grommet

Beautiful reproduction part for those of you who do not want to suffer the expense of the costly factory original. High quality impregnated rubber for long life. This seal fits around the perimeter of the front turn signal bucket and the lense screws against it.
Fitment

Discontinued
Fitment

Often overlooked in the restoration process, this seal is very easily replaced after removing the vent window cap and the vent window. It must be removed anyway when refinishing to avoid messy overspray.
Fitment

Often overlooked in the restoration process, this seal is very easily replaced after removing the vent window cap and the vent window. It must be removed anyway when refinishing to avoid messy overspray.
Fitment

This quality set of precision cut door seals are made by the leading manufacturer of door to body frame seals in the country! Impregnated with steel, this install just like the factory originals, and are beveled by us for a precise fit!
Fitment

This is the seal behind the door latch base. Made of nylonized rubber, this seal will never shrink or split. Sold each, fits left or right side.
Fitment

Due to overwhelming demand we finally took it upon ourselves to manufacture the much sought after lock cylinder weather seal. Long overdue in the market, this small plastic seal prevents water and debris from entering the lock cylinder and compromising its operation. This has never been available except with the complete exterior door latch assembly.
Fitment

Exellent reproduction for the fussy concours enthusiast who demands the best. Fits between the outer mirror and the doorskin was factory original equipment until discontinued. Our repro is excellent and made of high quality nylinized rubber for long life
Fitment

By far the best ones available in the market. Molded ends powdered, cannot be told from the expensive factory originals. Beware of the cheap repros cut from a roll, and install the best. Your 914 deserves it.
Fitment

These rubber seals squeeze the water from the window as the glass is rolled down. By far the best in the market. Top quality u. S . Made rubber, this set simply slides in with a bit of silicone grease.
Fitment

This is the seal that fits against the back of the rear window and buffers the engine lid keeping water out of the compartment. The original part has a steel spring embedded in it for attachment to the ledge and the repro glues on with some weatherstrip adhesive.
Fitment

Two great reproduction seals made by the leading manufacturer of trunk edge seals! Precise fit and almost identical to the factory originals, this set of the main u shaped trunk perimeter and front to the engine lid seal are easily installed with a slight bump from the heel of your hand.
Fitment

This is the small seal behind the door latch base towards the edge of the door. Made of nylonized rubber, this seal will never shrink or split. Sold each, fits left or right side.
Fitment

These custom made factory identical seals were never available from the factory as an individual part. Seal the tail light lense to the tail light body providing a comfortable wear-free seat for the valuable lens and keeping the water out of the assembly. Sold as a set and easily installed. If you have a water leak into the rear trunk, then simply remove the tail light body and reseal the tail light body to the rear panel with some silicone sealant.
Fitment

Attached to the rear of the targa top, this high quality reproduction seal should last even longer than the no longer available original. Never have we seen a better one, except for the factory original. Ours is vulcanized and molded for the best fit in the industry. Beware of the cheap glued seals that do not fit like ours do!
Fitment

Attached to the rear of the targa top, this high quality reproduction seal should last even longer than the no longer available original. Never have we seen a better one, except for the factory original. Ours is vulcanized and molded for the best fit in the industry. Beware of the cheap glued seals that do not fit like ours do!
Fitment

Why cut and chop some seal off of a roll when you can simply install an identical seal to the original factory molded version and save money at the same time? Our beautiful molded end seals are a precise slide in fit and reseal the top of the side window to the targa top!
Fitment

Why cut and chop some seal off of a roll when you can simply install an identical seal to the original factory molded version? Our beautiful molded end seals are a precise slide in fit and reseal the back of the side window to the targa bar! Why compromise paying more for junk?
Fitment

Our own great reproduction of the original factory seal now available at a super price!
Fitment