Vehicles
3 not categorized PORSCHE 911 BRAKE BUSHINGCan't find what you need? Try browsing the Accessories or Exploded Diagrams!
91135294400 View/Change Diagram
$12.06
Make a selection 91142354200 Nylon material same as the factory bushing 2 per car View/Change Diagram
From $3.33
Make a selection 9999240144A Inside of pedal console View/Change Diagram
From $14.75
Make a selection 1262770850 Known as: bush View/Change Diagram
From $5.23
Make a selection
$66.00
Make a selection 69542461100 Known as: friction ring View/Change Diagram
From $18.81
Make a selection 91442424700 Avoid purchasing a costly new emergency handle with these handy repair parts. A little labor and then the brake handle that works like new. View/Change Diagram
$16.42
Make a selection 901423015RB Tried to dismantle your pedal cluster to install new bushings and found that it is impossible to drive out the roll pin? Join the crowd! Time for a rebuilt cluster. All of our rebuilt clusters are completely dismantled, sand-blasted, painted, new parts used if needed, and reassembled with silicone bronze bushings. the only complete cluster available from anywhere! Includes brake light switch, brake push rod, throttle pivot, and rubber pedal pads. Ready to be installed! core charge...(choose a part on the right to read more) General Fitment914 1970-76911 1965-69 930 1975-77 911 1974-77 911 1970-73 912 1965-69
$425.00
Make a selection 903149 Worn brake pedal bushings or sticking accelerator bushings cause serious accidents. Oil-impregnated for lifetime lubrication, these bushings are superior in quality and longevity to cheap plastic factory or brass bushings. You cant afford not to install the best! This is a complete pedal box rebuild kit, with seven oilite bushings for the clutch cable arm, brake, clutch, and throttle pedals, and a new spiral retaining pin. Since the plastic original clutch cable arm bushing wears out so fast, we also sell this bushing from our package separately. General Fitment912 1965-69914 1970-76 911 1965-69 911 1987-89 911 1984-86 911 1978-83 930 1975-77 911 1974-77 911 1970-73
$44.00
Make a selection RS18 Set of two sealed monoball cartridges - front or rear. Most Porsche owners today, especially those of us who take our cars to the track, have equipped our cars with tires much wider and stickier than stock, which allows higher g-forces to be achieved in cornering and braking. During that type of hard driving, rubber suspension bushings are compressed and flexed by the extreme loads being put on them, defeating your car's finely tuned alignment settings, thereby reducing your braking and cornering potential. Monoballs are a downside-free improvement; because they eliminate four important sources of suspension slop without making your car's ride harsher. Your Porsche will handle and brake with greater precision...(choose a part on the right to read more) General FitmentBOXSTER 1997-04BOXSTER 2005-08 CAYMAN 2006-08 911 GT3 2007-11 911 2005-08 911 GT3 2003-05 911 TURBO/GT2 2001-05 911 1998-05
$250.00
Make a selection FVD34101707ATK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will properly install our FVD clubsport front control arm bushings, part # FVD341999r. They are made with 85 shore rubber (like the rennsport model). Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrangements can ...(choose a part on the right to read more)
$418.00
Make a selection FVD34101807ATK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will properly install our FVD clubsport front control arm bushings, part # FVD341999r. They are made with 85 shore rubber (like the rennsport model). Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrangements can ...(choose a part on the right to read more)
$418.00
Make a selection 90042349800 Includes silicone bronze replacements for: 2 - 901 423 253 00 accelerator, 2 - 911 423 341 01 clutch shaft, 2 - 901 423 343 00 clutch clevis, 2 - 911 423 542 00 brake, 1 - 900 309 002 00 roll pin General Fitment911 1965-69911 1970-73 911 1974-77 911 1978-83 911 1984-86 911 1987-89 912 1965-69 914 1970-76 930 1975-77
From $39.99
Make a selection
© 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |