Vehicles
70 not categorized PORSCHE 964 REAR LEDCan't find what you need? Try browsing the Accessories or Exploded Diagrams!<-- Try narrowing by car using the menu to the left.FVD3522945964R
$3,755.40
Make a selection FVD35233ABE The zimmermann sport brake disc combines high-quality cast materials, a vented and perforated braking surface and includes z-coating. Features: better wet braking performance by permanent expulsion of brake dust and water. Sporty look. Anti corrosion z-coating prevents rust. Noticeable improvement in braking performance. Countersunk holes double as wear indicator. Simple bolt on, modifications are not necessary. Sold individually. 2 rotors would be needed for the rear axle. Left or right side fitment. Please note: not for cars with the mo30 sport suspension. The clearance item listed is not coated with z-coating . Specific model fitment listed below. General Fitment968 1992-95911 1989-94 944 1982-85 944 1985-88
From $143.00
Make a selection FVDBSK35296402S Make your next brake service a breeze with our pre-packaged service kits. Quality means everything to us, so we only source these parts directly in Germany. This kit contains: - 2 qty. Sport rear rotors (zimmermann), part # FVD35233abe - 1 qty. Oem set of rear pads (4 total), part # 96435294903 - 2 qty. Oem brake warning sensors, part # 96461236502 - 4 qty. Oem brake pad damping shims (28 mm piston), part # 99635208602
$469.70
Make a selection 10050330000 This 9 inch front and 11 inch rear steel fender flare set is made in Germany, we offer a complete line of replacement bodywork to complement the entire Porsche model range. Sold individually. 1 necessary per car. Please note: for conversions, these flares will allow you to run 9 wide tires in the front and 11 wide in the rear. For the 964 / 965 models the torsion bar cut out must be filled. Due to variances in production at the factory, age, accident damage or rust, each part may require trimming and or adjustment for perfect fitment.
$1,648.90
Make a selection 115900964BI01 Bilstein b16 (pss10) suspension kits feature ride height adjustability with 10-stage manually adjustable dampers. Simply adjust compression and rebound settings, from comfort to competition, by rotating the setting number knob at the base of the shock. The front and rear progressive rate springs allow accurate adjustment of the vehicle ride height and center of gravity for the level of performance you seek. Ride height is adjustable from 1.0 to -1.5 20-40mm (front) & -1.0 to -1.5 20-40mm (rear - minimum 1 lowering). Bilstein b16 (pss10) suspension allows you to enjoy the kind of precise suspension tuning formerly available only on race cars. We recommend purchasing our lowering collar kit if you plan to run the...(choose a part on the right to read more)
$3,855.50
Make a selection 9655592960001C This seal sits above the rear most rocker panel section just in front of the rear wheel well. It seals the side skirt / rocker panel, part # FVD33398600 sold individually. Passenger's side fitment. For 964 turbo look / 965 turbo. View/Change Diagram
From $19.80
Make a selection 115343708 This is a genuine Porsche 964 c2 / c4 model rear sway bar for the early 1989 and 1990 models. It is 20 mm thick and includes bushings. Perfect as a replacement for original number 964 343 707 33. Sold individually. 1 needed per car. General Fitment911 1989-94
From $739.79
Make a selection 115900991BI Only for cars without pdcc ( active stabilizer ) bilstein b16 (pss10) suspension kits feature ride height adjustability with 10-stage manually adjustable dampers. Simply adjust compression and rebound settings, from comfort to competition, by rotating the setting number knob at the base of the shock. The front and rear progressive rate springs allow accurate adjustment of the vehicle ride height and center of gravity for the level of performance you seek. Ride height is adjustable from 1.0 to -1.5 20-40mm (front) & -1.0 to -1.5 20-40mm (rear - minimum 1 lowering). Bilstein b16 (pss10) suspension allows you to enjoy the kind of precise suspension tuning formerly available only on race cars. We recommend purchasi...(choose a part on the right to read more)
$4,153.60
Make a selection 100555112NB German lightweight sliverknit rear seat delete / rear shelf carpet that was used on the 964 and 993 rennsport models. We go to extra lengths to ensure that our carpets are made as closely to the originals as possible. Each carpet is made with original lightweight German sliverknit and are trimmed in vinyl. Each is cut, sewn and trimmed to fit perfectly. Made in Germany. Sold individually.
$1,151.70
Make a selection 911561053652XW This is the rear outer section of the cabrio top made in Germany with original sonnenland material. It is as close to the original as possible and is cut and trimmed to fit perfectly. It includes a pvc plastic rear window with a zipper like the original. If the window gets hazy simply unzip, remove and add a new window. Sonnenland material consists of 3 layers, dyed acrylic twill weave top layer, elastomeric rubber inner layer and polyester woven base layer. It provides increased strength against abrasion, increased fade resistance and the tighter woven layers are made for modern electric tops with stronger frames for the 911 and 964. Sonnenland high quality material was originally used by Porsche and other top...(choose a part on the right to read more) View/Change Diagram
From $1,058.20
Make a selection 12637023CSR Power slot rear right cryogenic slotted rotors Porsche 964 Carrera 2 2s 90-94 General Fitment911 1989-94944 1985-88 944 1989-91 968 1992-95
$186.15
Make a selection 12637023CSL Power slot rear left cryogenic slotted rotors Porsche 964 Carrera 2 2s 90-94 General Fitment911 1989-94944 1985-88 944 1989-91 968 1992-95
$186.15
Make a selection 911051 Porsche 911 ac compressor upgrade kit, 1984-89, lh drive model provides improved integrity with our kuehl barrier hose set, kuehl low- high pressure switch to help protect the system, a new denso factory compressor with clutch, new kuehl drier, complete o-ring kit, along with r134a charge port adapters. you can use either r12 or r134a with refrigerant with this complete kit. all barrier hoses match OEM configuration, have sae sae approved crimped fittings and each hose is labeled so you know where it goes.
$1,097.00
Make a selection 96410601402EQ This OEM cover sits low nearest the rear bumper. If you are removing the motor for maintenance, be sure to check and replace the engine covers / heat shields as necessary. We recommend purchasing a new seal, part # 96410622301 and plug, part # 96410623701 to complete the installation. Sold individually. 1 necessary per car.
$601.70
Make a selection 91163162004 Perfect as a replacement or when you are upgrading your 964-rear center bumper section to the rs / turbo 3.6 spec. Includes gasket and bulb. The 964 / 965 FVD rear rs / turbo 3.6 l center section is part # FVD505123964rs for the 911 and 914, please check the models tab to make sure that this fits your car. Sold individually. 2 necessary per car. View/Change Diagram
From $26.10
Make a selection 9645592950101C This seal sits above the rear most rocker panel section just in front of the rear wheel well. It seals the side skirt / rocker panel, part # 96455909501g2x sold individually. Driver's side fitment. View/Change Diagram
From $18.70
Make a selection 96433102100RATK Unsure about installing a replacement bushing? Send us your trailing arm and we will properly recondition and install the bushing for you. The reconditioning process includes full inspection of your trailing arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we properly install our rear clubsport trailing arm bushings, part # FVD3310212291. Our rear trailing arm bushings contain rubber inserts with a shore hardness value of 85, like what is used on rennsport models. They offer rs style handling characteristics, superior durability and are still forgiving enough for street use. When reconditioning the trailing arms, we als...(choose a part on the right to read more)
$672.10
Make a selection 96420725103 This hose connects the rear of the oil tank to the thermostat housing. We recommend replacing 2 qty. Clamps, part # 99951225202 when replacing this piece. Sold individually. 1 necessary per car. Please note: this will only fit the oil thermostat with part # 964 207 047 05 or 964 207 047 07 or 964 207 047 08. View/Change Diagram
From $18.00
Make a selection 96433102200RATK Unsure about installing a replacement bushing? Send us your trailing arm and we will properly recondition and install the bushing for you. The reconditioning process includes full inspection of your trailing arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we properly install our rear clubsport trailing arm bushings, part # FVD3310212291. Our rear trailing arm bushings contain rubber inserts with a shore hardness value of 85, like what is used on rennsport models. They offer rs style handling characteristics, superior durability and are still forgiving enough for street use. When reconditioning the trailing arms, we als...(choose a part on the right to read more)
$672.10
Make a selection 96433370106 This is a genuine 20 mm thick, Porsche 964 c2 / c4 model rear sway bar for models from 1991-94 models with manual transmissions (m481 option). Please note: this item is a special-order item. Special-order items are sold on a non-cancelable, non-exchangeable, non-returnable, non-refundable basis. Sold individually. 1 needed per car. View/Change Diagram
From $304.85
Make a selection 9645592960101C This seal sits above the rear most rocker panel section just in front of the rear wheel well. It seals the side skirt / rocker panel, part # 96455909601g2x sold individually. Passenger's side fitment. View/Change Diagram
From $18.70
Make a selection 96454303602 Necessary when replacing your right rear quarter window, as this seal retains the window in the body and prevents moisture from getting in. For 964 coupe models. Sold individually. 1 needed per car. Passenger's side fitment.
From $89.00
Make a selection FVDBSK352964002 Make your next brake service a breeze with our pre-packaged service kits. Quality means everything to us, so we only source these parts directly in Germany. This kit contains: 2 qty. Rear rotors (zimmermann), part # 951 352 041 02eq 1 qty. Oem set of rear pads (4 total), part # 964 352 949 03 4 qty. Oem brake pad damping shims (38 mm piston), part # 996 352 086 02 2 qty. Oem brake warning sensors, part # 964 612 365 02 sold as a kit. 1 necessary per car.
$332.20
Make a selection 964561005016HA This is a complete cabrio top made in Germany with original sonnenland material. It is as close to the original as possible and is cut and trimmed to fit perfectly. Includes a trapezoidal pvc plastic rear window with a zipper like the original. If the window gets hazy simply unzip, remove and add a new window. Sonnenland material consists of 3 layers, dyed acrylic twill weave top layer, elastomeric rubber inner layer and polyester woven base layer. It provides increased strength against abrasion, increased fade resistance and the tighter woven layers are made for modern electric tops with stronger frames, like the 911 and 964. Sonnenland high quality material was originally used by Porsche and other top German ...(choose a part on the right to read more)
$2,201.10
Make a selection 9655592950001C This seal sits above the rear most rocker panel section just in front of the rear wheel well. It seals the side skirt / rocker panel, part # 96555919502g2x sold individually. Driver's side fitment. For 964 turbo look / 965 turbo. View/Change Diagram
From $19.80
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |