![](https://30ed524141d0cac60ab4-d2e2d18a14257de3b9ce428cf077ee97.ssl.cf2.rackcdn.com/acban.jpg)
PORSCHE 924 GT AC INSTALLATIONCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 356 1950-59 - Electrical (includes uncategorized and accessory items) ![]() 90134719102EQ Prevent premature steering rack failure by replacing a torn or worn boot or bellow. We recommend replacing this boot with a new steering rack or tie rod installation. High-quality OEM (original equipment manufacturer) replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 2 necessary per car. Please note: please check the model fitment tab to ensure accurate fitment.
$23.10
Make a selection 61660320300 This reproduction regulator replaces the long-discontinued "black box" Bosch voltage regulator which sits on the firewall in the engine compartment. This new part fits exactly like the original regulator, with all holes aligning to the ones on the firewall. Much development time went into this regulator and it's performance; it can handle up to 50 amps, enough for the points inside not to burn. This model is for 6 volt cars in the original factory configuration. View/Change Diagram
$270.00
Make a selection 115050060020 Contrary to the tender spring which usually has a full effect on the road behaviour, the helper spring's only use is to fix the main spring in the spring seat when the wheel is completely released. Thus the helper spring prevents the loosing of the spring when the wheel gets released. The installation of the helper spring has no effect on the suspension characteristics of the vehicle. By using of the helper spring, spring-to-perch gaps of up to 50 mm can be covered.
$82.50
Make a selection 115971AAR01 Panamera models with optional air suspension utilize four sensors to control the ride height. This is accomplished via the use of a small linkage or link which connects the sensor to the suspension. As the car is raised or lowered, the link moves the sensor up or down sending a signal to the computer telling it how high the car is. When you replace the non-adjustable factory link with this adjustable design, the output of the sensor makes the computer believe that the car is higher than it is. So, the computer will lower the ride height. The simplicity of this setup is that it retains full functionality of the factory system. Be warned, all adjustable lowering links are not the same! These links are machined al...(choose a part on the right to read more)
$324.50
Make a selection 846R9003 Material: tig welded, type 304, stainless steel. Finish: satin finish stainless. Weight: 6oz. Models: 996/997, Boxster, 911 & 944. Installation: secures snap-in lap belts to outside seat belt mounting point. Miscellaneous: allows user to remove and install belts in seconds. Will not interfere with factory seat belt. One pair will work for both seats. Use part 846r-9001 for inside belt mount.
$112.20
Make a selection 90164510100 Original restored blaupunkt radio for all very late 356 models and 65-68 911 and 912 models. White face, single case am fm shortwave, perfect for the concours competition. if you have a like core we can give you a 75 dollar core credit upon its return and checkout please see our listings for the installation kit, the ipod adaptor and the correct speakers
$695.00
Make a selection 27021102901 This is a high-quality replacement for original number, 930 211 029 01 manufactured by dansk. It is manufactured in stainless steel. It is a replacement part dansk offers a complete line of replacement parts to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. This commitment has made dansk one of the original equipment suppliers to the Porsche in Germany. For a proper installation, we recommend heat exchanger installation kit, part # FVDmk911103 sold individually. Right or left side fitment. 2 necessary per car.
$1,417.90
Make a selection 270503055 High-quality OEM front chin spoiler kit replacement that includes all necessary installation hardware. We source this part in Germany to ensure quality, reliability and precise fitment. Kit includes: qty. 1 front chin spoiler 930 / 911 wide body / turbo look 1975-89 - 93050305501 qty. 11 spoiler shim - 91150302300 qty. 1 left spoiler mounting plate qty. 1 right spoiler mounting plate qty. 15 m6 stainless nuts qty. 15 m6 washers sold individually. 1 needed per car.
$2,001.90
Make a selection 99363103200 Complete halogen headlight that includes a lens, gasket, h1 bulb, electric motor for headlight levelling, end cap, retaining bar and connector housing. It is complete and ready for installation. Sold individually. 1 necessary per car.
From $1,241.90
Make a selection 240600101 Waterproof cloth tape for reliable sealing, masking or concealing of racing fender benders. High initial tack and extremely good adhesion. Pe coated cloth tape, waterproofed. Excellent for repairs, crafting and fixing. Extra strong adhesion, which also allows installation on uneven surfaces. 50 mm wide x 50 meters long.
$18.70
Make a selection 240600110 Waterproof cloth tape for reliable sealing, masking or concealing of racing fender benders. High initial tack and extremely good adhesion. Pe coated cloth tape, waterproofed. Excellent for repairs, crafting and fixing. Extra strong adhesion, which also allows installation on uneven surfaces. 50 mm wide x 50 meters long.
$27.50
Make a selection 24135299702RS Tired of having to wash the car just due to brake dust build up? Ebc redstuff brake pads have you covered. They reduce brake dust by 60-90%, plus the minimal dust is safely removed with a wet sponge as redstuff does not contain steel fiber particles found in other pads. These pads also have excellent brake friction when cold and just get better as they warm up. The pads are composed of a kevlar fiber-based brake compound enhanced with ceramic particles. The benefits of this material are longevity, enhanced braking performance, quiet operation and reduced brake dust. Features: made for up to 750*c (1,382*f) for street, track and rally use. Low dust, high performance street pad with 20-25% braking improvement. Ca...(choose a part on the right to read more)
$261.80
Make a selection 240600102 Waterproof cloth tape for reliable sealing, masking or concealing of racing fender benders. High initial tack and extremely good adhesion. Pe coated cloth tape, waterproofed. Excellent for repairs, crafting and fixing. Extra strong adhesion, which also allows installation on uneven surfaces. 50 mm wide x 50 meters long.
$18.70
Make a selection 2699 The wrench is flat and wide and was designed to hold a tensioner pulley in place while the retaining nut is applied. The retaining-nut usually over hangs its base therefore the wrench has to be flat. No conventionally sold metric key-wrench will clear the base for the retaining-nut installation. Do not look for something else. It was tried before you. It just will not clear. Two types of tensioner pulleys are used in 924-944 today. The metal tensioner pulley and the plastic tentioner pulley.
$43.99
Make a selection 170211021 This is a high-quality replacement for original number, 911 211 021 60 manufactured by dansk. It is manufactured in steel and includes a corrosion resistant protective coating. Dansk offers a complete line of replacement parts to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. This commitment has made dansk one of the original equipment suppliers to the Porsche in Germany. For a proper installation, we recommend heat exchanger installation kit, part # FVDmk911100 sold individually. 1 necessary per car. Please note: the corresponding right side is our part # 170211022
$1,038.40
Make a selection 21011125PSE Only for vehicles with Porsche standard sports exhaust system 200 cell, hjs tri-metal, hf (high flow) hjs catalytic cores with "u-torque" design, manufactured by m in Germany. The u-torque design compensates for the backpressure loss while running the high flow cats. The design minimizes the loss of low end torque and adds 10-15 ft-lbs of torque in the mid and top range of the rpms. Why settle for the traditional cross over cat design when you can add more torque in the mid-range and minimize the loss of torque down low where the 997's need it most! Please note: these fit the OEM mufflers and Porsche sport exhaust (pse) mufflers. Tech tip:add one of our installation kits FVD mk 997300
$3,311.00
Make a selection 21011196538 This sport muffler is engineered for the discerning Porsche 965 turbo owner who is interested in pure unbridled power and sound. It is hand made from t 321 grade stainless steel. All piping is mandrel bent for reduced backpressure and increased performance. The sport muffler exudes a lower, deeper linear-firing-order dominated flat 6 Porsche turbo sound with added turbo whistle. Exhaust tips are 76 mm (3 inch) polished ovals with a rolled lip. Each kit includes complete installation hardware, wastegate pipe and clamps. Features: gains of up to 10 hp more* t 321 stainless steel mandrel bent new wastegate pipe new gaskets new hardware new muffler clamps *dependent upon boost level and other modifications. Sold in...(choose a part on the right to read more)
$2,127.42
Make a selection 17021102103 This is a high-quality replacement heat exchanger manufactured by dansk. It is manufactured in steel and includes a corrosion resistant protective coating. Dansk offers a complete line of replacement parts to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. This commitment has made dansk one of the original equipment suppliers to the Porsche in Germany. For a proper installation, we recommend heat exchanger installation kit, part # FVDmk930100 sold individually. Right or left side fitment. 2 necessary per car.
$837.10
Make a selection 99650598600 This will also fit the 996 mk1 (98-01) with the factory cup aero kit. Please note: does not include installation hardware. Please order the installation hardware kit part # 99650598691mk
From $555.00
Make a selection 17021102501 This is a high-quality replacement for original number, 930 211 025 01 manufactured by dansk. It is manufactured in steel and includes a corrosion resistant protective coating. Dansk offers a complete line of replacement parts to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. This commitment has made dansk one of the original equipment suppliers to the Porsche in Germany. For a proper installation, we recommend heat exchanger installation kit, part # FVDmk911102 sold individually. Right or left side fitment. 2 necessary per car. Please note: this will not fit u.s. 3.0 l SC mode...(choose a part on the right to read more)
$642.40
Make a selection 190111043G For use on obd1 (94 and earlier) cars only! Only 1 o2 bung is provided. Call for 1995 application. Will not work with multiple o2 sensor cars, like north american cars. (96-98) does not include a TUV-certificate. We recommend using our catalytic installation kit, part # FVDmk993300g please note: not legal for use on california pollution controlled motor vehicles.
$705.10
Make a selection 10010303204 - 3.2 l for increased horsepower and torque.* - genuine mahle forged pistons with deeper valve pockets. - genuine mahle steel (st52) nikasil coated cylinders.** - piston pin bore is off center (deaxiated) for factory quiet operation. - 10.3:1 compression. - 98 mm big bore. - 22x58 racing wrist pins - 70.4 stroke. - made in Germany by mahle gmbh. - piston rings installed directly on the pistons for ease of installation. - complete set with cylinders, pistons, rings, wrist pins and clips. - kit weighs 21.03 lbs. (9.54 kg). Mahle pistons are forged for substantially higher and more uniform strength over pistons that are cast. Mahle cylinders are manufactured from st52 steel which has extremely high thermal resista...(choose a part on the right to read more)
$9,693.51
Make a selection 1002110221DA This is a high-quality replacement for original number, 911 211 022 10 manufactured by dansk. It is manufactured in stainless steel and includes the necessary brackets and tabs for a direct bolt on replacement. Dansk offers a complete line of replacement parts to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. This commitment has made dansk one of the original equipment suppliers to the Porsche in Germany. For a proper installation, we recommend heat exchanger installation kit, part # FVDmk911100 sold individually. 1 necessary per car.
$1,329.90
Make a selection 17092102S This cross over connector replaces original part # 930 111 157 01, it is a quality stainless steel replacement part manufactured by dansk. They offer a complete line of replacement parts to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. This commitment has made dansk one of the original equipment suppliers to the Porsche in Germany. For proper installation, we recommend a new exhaust gasket, part # 93011119307 and sealing ring, part # 91111118903 sold individually. 1 necessary per car.
$82.50
Make a selection 0760310874 This book is a must for anyone thinking about rebuilding their own 911's engine. Never-before published information details the nuances of tackling this daunting task! From dropping the engine, to reconditioning and blueprinting, through final reinstallation and break-in, dempsey guides you step-by-step through the pitfalls often experienced by even the best mechanics. Contains reliable information on parts interchange, performance modifications, reliability upgrades, tear down, and potential problems encountered along the way. Essential information for do-it-yourselfers and for those looking to hire a professional. This book provides excellent insight and information into the inner workings of the air-cooled ...(choose a part on the right to read more) General FitmentACCESSORY
$34.50
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |