PORSCHE 964 SIGNSCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 356 1950-59 - Engine (includes uncategorized and accessory items) FVD803993VS0222 High quality, German made three-point replacement safety belt, designed to perform like the original. Features / specs: belt length: 300 cm (118 inches) 3 point inertia reel belt angle adjustable reel (max. Of 8 *) includes 22 cm (8.5 inch) buckle, installation hardware and caps. Din-en-iso 9001: 2000 quality standard manufactured, e-mark approved. The matching rear belt is part # FVD803993hr sold individually. 2 necessary per car.
$162.80
Make a selection 91163196400EQ Fog lights are prone to stone chips and cracks. Inspect and replace them before they allow moisture in. Quality aftermarket replacement designed to perform like the original. Sold individually. Drivers or passenger's side fitment. 2 necessary per car.
$41.80
Make a selection FVD803993HR High quality, German made replacement lap safety belt, designed to perform like the original. Features / specs: includes buckle, installation hardware and caps. Din-en-iso 9001: 2000 quality standard manufactured, e-mark approved. The matching front belt is part # sold individually. 2 necessary per car.
$187.00
Make a selection E2290 K&N filters – treat your car with the best breath possible. These high quality filters improve performance, while saving you money. Providing additional power through its unique design, these filters replace the standard filter element and are very low restriction, so they improve engine breathing. Because they allow more air into your engine, the result is more power along with improved fuel economy. You’ll never buy another filter for your vehicle once you install the K&N. When the filter does become dirty, simply take it out and wash it, re-oil it and use it again. Each K&N filter comes with a one million mile warranty. Our recharger kit will allow you to remove and clean your filter 3 times! Photo shows...(choose a part on the right to read more) General Fitment356 1950-59356 1960-65
$44.95
Make a selection BBI9964010006 Finally, a solution that allows you to safely increase without the risk of damaging your front axles. as you add GT3 shims to your front Porsche 996/997 turbo lower control arms, you move the cv joints beyond their safe range of motion, risking failure and expensive damage. These 10mm thick precision spacers, used with 16mm of lca shims will provide an additional -1.7 deg. Of camber, while maintaining the factory cv joint and axle relationship. the spacer design features a concentric lip that positively and accurately locates it to the cv joint for perfect balance and no vibration. Each kit includes two spacers and all the needed hardware in high class 10.9 grad
$375.00
Make a selection ST215 This professional-grade flywheel lock is designed to be used to secure the crank shaft from rotating during removal and reinstallation of all 6v or 12v air-cooled motors. Used in conjunction with engine holding fixture (rstp201) where the flywheel lock bolts into a machined channel. General Fitment356 1950-59356 1960-65 912 1965-69 914 1970-76 911 1965-69 911 1994-98 911 1989-94 911 1987-89 911 1984-86 911 1978-83 930 1975-77 911 1974-77 911 1970-73
$75.55
Make a selection SIC10299189 Over time, sealing surfaces will become grooved, making a good seal impossible. The most economical and fastest method of shaft repair is to install th cr speedi sleeve. Speedi sleeve is a precision engineered piece of stainless steel. It's ultra-thin wall design allows it to be used without changing the seal size, and it's finish is perfect for lip sealing applications. Speedi sleeve is built with a removable installation flange. The installation tool included in every box allows the seal to be put on. This avoids the possibility of distortion from heat or other installation methods. General Fitment356 1950-59356 1960-65 912 1965-69
$66.32
Make a selection 99660610599 If you are noticing engine vibrations, misfires and even backfiring your crankshaft position sensor maybe bad. Your car's dme (ecu) uses the signal from the crankshaft position sensor to control ignition timing and fuel injection, so if your sensor is failing your engine is suffering from poor timing and is not running efficiently. This kit is complete and ready to install.
$132.77
Make a selection 170111047 This stainless-steel exhaust tip offers a period correct, timeless design with a larger diameter. It fills out the bumper cut out nicely and is manufactured in europe. Specifications: rolled lip. Polished finish. 4 (102 mm) round to fill in the entire bumper cut out. Weight: .79 kg (1.74 lbs.) sold individually. 1 necessary per car.
$141.90
Make a selection FVD803993VR0230 High quality, German made three-point replacement safety belt, designed to perform like the original. Features / specs: belt length: 300 cm (118 inches) 3 point inertia reel belt angle adjustable reel (max. Of 8 *) includes 30 cm (11.8 inch) buckle, installation hardware and caps. Din-en-iso 9001: 2000 quality standard manufactured, e-mark approved. The matching rear belt is part # FVD803993hr sold individually. 2 necessary per car.
$187.00
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |