PORSCHE 944 TURBO ORDS OCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 356 1960-65 - Body (includes uncategorized and accessory items) AP9972TT170 The stock exhaust of the Porsche 997.2 turbo is very restrictive compared to aftermarket systems. Porsche does this to meet sound and emission purposes like most OEM manufacturers. agency power set out to create an exhaust system for the new Porsche 997.2 turbo 6speed or pdk that did not drone, would produced amazing performance, and under throttle give an incredible sound. we have accomplished this! the new agency power exhaust not only saves about 30lbs off the rear end, it also improves power quite a bit.
$3,749.95
Make a selection 99919234350EQ Belts undergo a lot of friction and wear. They are cost effective to change and will keep your alternator and engine in good condition. Be sure to follow recommended service and replacement intervals set by Porsche on belts. For 964 c2 tip trans. / 993 tip trans. / 993 c2/ s manual trans. And the 993 turbo. Sold individually. 1 necessary per car.
$11.00
Make a selection 99610090399 Head gasket set for 996 turbo and GT2 exclusive from FVD ! Set contains all gaskets and seals for an engine overhaul. Please order crankcase gasket set (996 100 996 tuam)separately.
$1,542.20
Make a selection BES98215000S2 The open architecture of this muffler allows for a deeper four-cylinder turbo tone, with plenty of whistling on tap. Coming off throttle from higher rpms exudes a chorus of snarling, gurgling and crackling letting everyone know that this car is not your average 982. + 15 hp & + 12 tq gain. - 2 x 3.5 (90 mm) round tips. - thermal insulation on piping to keep suspension components cool. Withstands up to 2,012 degrees fahrenheit (1,100 degrees celsius). - lower deeper tones than the factory exhaust with far more whistling and gurgling / crackling off throttle. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - no drone in the cabin. - "aero quip" style motorsport muffler connections t...(choose a part on the right to read more)
$2,816.00
Make a selection BES98215000S The open architecture of this muffler allows for a deeper four-cylinder turbo tone, with plenty of whistling on tap. Coming off throttle from higher rpms exudes a chorus of snarling, gurgling and crackling letting everyone know that this car is not your average 982. + 15 hp & + 12 tq gain. - 2 x 3.5 (90 mm) round tips. - thermal insulation on piping to keep suspension components cool. Withstands up to 2,012 degrees fahrenheit (1,100 degrees celsius). - lower deeper tones than the factory exhaust with far more whistling and gurgling / crackling off throttle. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - no drone in the cabin. - "aero quip" style motorsport muffler connections t...(choose a part on the right to read more)
$3,367.10
Make a selection BES99120040S Take your 991.1 or 991.2 turbo or turbo s to a new level with these muffler bypass pipes. They produce the wildest sound available on the market today and are a perfect upgrade for level 3 or 4 car used on the track. They produce loud, low, deep tones with exaggerated turbo whistling and sinister gurgling and crackling off throttle. By far the best sound you can get out of your turbo, not to mention being able to shoot flames! The only real drawback is the drone in the cabin which we try to minimalize by stepping down the diameter in 3 stages. Features: - + 35 crank hp & + 25 crank torque - 3 tubing (75mm) that tapers down to 2.25" (57mm) to prevent turbo damage. - weighs 7 lbs. (3,1 kg) - German v2a - x5crni1...(choose a part on the right to read more)
$585.20
Make a selection BES99715040S2 Quiet version with catalytic bypass and 4x80mm end tips these versions of FVD sport exhaust system is specifically made for increased performance vehicles. Designed for tolerable, pleasant and sonorous sound (especially for the turbo cabriolet). The elimination of the catalysts reduced drastically the back pressure and increases the performance and throttle response to the max! - stainless steel exhaust system - catalytic bypass - 4x80mm end tips - 2 3/4 tubing (70mm) straight through design for maximum power - weighs 39 lbs. (18,1 kg) - made in Germany - dme programming necessary (catalytic adaption) - stock tips will fit. Tech tip: order also repair / gasket set FVD mk9 970 02
$2,928.20
Make a selection FSPOR992TVLV Treat your 992 turbo to the finest cat-back exhaust solution on the market. This valveed exhaust system is plug-and-play with the factory pse system so you can turn pse off for quiet highway cruising and turn pse on for ripping twin turbo sports car sound!
$5,245.95
Make a selection 22011099706 The 997 turbo ipd "y" pipe was built for the more demanding turbo performance customer. The factory y pipe becomes restrictive when adding substantial power gains. The ipd "y" pipe has larger inlets and an optimized diversion area allowing for even greater power gains. This superior and more efficient design flows 126 more cfm than the factory y pipe delivering the additional power needed to raise the performance bar on any turbo. The ipd "y" y pipe is designed to be a direct replacement of the factory OEM y pipe. There are no modifications or fabrication required for installing the ipd y pipe. This is an easy and straight forward r & r (remove and reinstall) bolt on upgrade. Note: contains everything nec...(choose a part on the right to read more)
$1,094.50
Make a selection FVD10397501CARR Connecting rod with plc carr-6 screw. The s connecting screw (plc carr-6) needs only every third time to be changed under race conditions or motor sport use when overhauling the engine. When used in 997.1turbo connecting rod bearing 99310314715set must be used (tongue / nose opposite). Carrillo is one of the most respected connecting rod manufacturers in competitive motor sports. Carrillo rods are constructed from their propriety alloy and forged to their custom specifications. The rods are then fully machined to guarantee the removal of all surface imperfections. After heat treatment, each connecting rod is magnaflux inspected and hardness checked, then machined to final size. Each set is balanced and then sho...(choose a part on the right to read more)
$2,952.40
Make a selection FVD10699711 For 996 turbo/gt2 and 997 GT2/gt3. - specially designed for tuned and motorsport vehicles the racing & high performance division of csf build and engineer the most advanced, efficient, and reliable cooling systems in the world. Csf manufacturers radiators with high performance all-aluminum and direct-fit replacement for racecars. The only high performance manufacture to feature this advanced technology. These radiators are stamped to the same geometry of the application's original plastic end radiators. These tanks feature less welding, and are generally considered the strongest tank designs in the industry.
$548.90
Make a selection FVD95861880MG Genuine: engine - v8 capacity - 4806 ccm compression ratio - 12,5:1 max. Power - 309kw (420hp) @ 6500rpm max. Torque - 500nm @ 3500rpm max. Speed - 256km/h max. Rpm - 7000rpm acceleration 0-100km/h - 6,0s tuning: max. Power - 325kw (442hp) @ 6000rpm max. Torque - 530nm @ 4500rpm max. Speed - 265km/h max. Rpm - 7200rpm acceleration 0-100km/h - 5,7s for 27 + years, FVD-Brombacherhas been setting the standard for Porsche engine building and tuning in Germany. Our deep understanding of the flat 6 Porsche engine naturally led to our engine management software. Over the years we have perfected the art of software tuning, making substantial gains in horsepower and torque, while retaining drivability and most importan...(choose a part on the right to read more)
$1,484.16
Make a selection 99310117054 This is the original stud used in the rennsport and turbo (m64.20 / 60) models. We recommend them for your next engine rebuild. Sold individually. 24 necessary per car.
From $53.90
Make a selection FVD123014ATK K-16/24 turbo (up to 555hp) power is focused on low and mid range rpm's. Facts: larger compressor wheel with extended tip. 47.5mm inducer diameter. Cnc modified compressor housing modified and improved back plane uprated staggered gap turbine uprated thrust bearing modified wheel to reduce backpressure balancing of all components factory vacuum unit new bearings and seals all parts are reconditioned and balanced FVD brombachers 993 k-16/24 remanufactured turbos are created for those who are looking for power that is focused in the low and mid rpm range. They are completely bolt on and do not require custom headers or special modifications. The remanufacturing process starts with re-profiling the OEM turbocharg...(choose a part on the right to read more)
$2,976.60
Make a selection FVD123025ATK K24/26 exchange turbo (only OEM k24 exchange accepted) (up to 700 hp) power is focused on mid and top range rpm's. Facts: - modified compressor housing and backing plate - modified & lightened high flow compressor wheels. - remanufactured by kkk / borg warner certified technicians - free software update for those already running FVD software. FVD brombachers 996 k24/26 race turbos are new units created for those who are looking for ultimate in performance. Power is focused in the mid and top rpm range while keeping turbo lag low. They are completely bolt on and do not require custom headers or special modifications. The factory OEM turbocharger compressor housing is re-profiled and the compressor backing plate...(choose a part on the right to read more)
$2,976.60
Make a selection FVD50599702MM Front bumper air vent grill an important component for both cooling and aerodynamics. Ensuring the rapid removal of hot air optimized unit cooling front bumper rs grill for all Porsche 997 Carrera models incl. 4s / GTS / GT3 / turbo
$366.30
Make a selection FVD123013 K-16/24 turbo (up to 555 hp) power is focused on low and mid-range rpm's. Facts: larger compressor wheel with extended tip. 47.5mm inducer diameter. Cnc modified compressor housing modified and improved back plane uprated staggered gap turbine uprated thrust bearing modified wheel to reduce backpressure balancing of all components factory vacuum unit new bearings and seals all parts are reconditioned and balanced FVD Brombacher993 k-16/24 new turbos are created for those who are looking for power that is focused in the low and mid rpm range. They are completely bolt on and do not require custom headers or special modifications. The process starts with re-profiling the OEM turbocharger compressor housing and m...(choose a part on the right to read more)
$2,976.60
Make a selection FVD20799601 Scavenging and aeration in the oil pan have been identified as a problem in 996 and Boxster models experiencing high g-forces on the racetrack. This oil pan spacer provides a simple solution. This spacer increases sump capacity by half a liter, providing more reserve to ward off starvation. Thisoil pan spacer clears all factory options including the rear skid plate. Added oil capacities as well as increased oil pan surface area increase oil cooling and engine performance. *oil pan and sump baffle are OEM parts and do not need to be purchased material: 6061 t6 aluminum alloy finish: clear anodized weight: n/a models: Boxster, Boxster s, and 996 models (excludes GT3 and turbocharged models) installation: for best...(choose a part on the right to read more)
$283.80
Make a selection FVD12399600R Silicone boost hose kit FVD's direct replacement boost hose kit eliminates common boost hose "blow outs" on modified turbo's. Facts: tested to withstand over 75 psi (5 bar) boost pressure.fuel and oil resistanttemperature range between - 50 to + 180 degreesbolt on kit over time the OEM boost hoses tend to expand and contract under higher load, which leads to leaks, or "blow outs". Also, the OEM aluminum end does not secure properly into the intercooler, which causes boost leaks, and boost hose blowouts. Our machined billet ends are a perfect secure fit and our silicone hose is designed not to expand under boost pressure. The hose kit is a complete bolt on kit.
$590.70
Make a selection FVD50599704MM Side skirts set tradition rs our side skirts are much wider than the stock components, which leads to a wider underbody and thus to more downforce. The mounting is very easy. Plug&play at the OEM screwing points. For all Porsche 997 Carrera with the (c4) wide body | 4 | 4s | GT2 rs | GT3 rs | turbo
$1,075.80
Make a selection FVD504993RS Made of polyurethane so they will not chip or crack like fiberglass, and are flexible enough to survive small impacts. Simple installation without any modifications to the original bodywork. Sold as a set (left and right). Not for wide body cars (993 turbo or turbo-look). Please note: these are aftermarket products. All aftermarket products need to be prepped, sanded, gaps checked / filled and painted. We only recommend professional installation with a shop that has aftermarket bodywork experience.
$696.30
Make a selection FVD351997TTCS This kit convert's the 997 turbo pccb rotors to steel rotors with yellow pagid pads.( only 5-hole, not central lock ) this system is complete with everything that you need to install. Do not ruin your expensive ceramic brake discs on the track. Get ready for racing with the original and much cheaper Porsche motorsport steel brake discs! What's in the box: 4 x 2-piece brake discs (380 x 34 mm - front / 350 x 28 mm - rear) 4 x wear sensors 2 x set ( front and rear ) brake pad set (pagid yellow - rs29 ) 8 x screws for brake caliper 8 x damping plates technical tip: also order stainless steel brake lines (FVD b96 355 97) and racebrake fluid (012 145 ca).
$6,344.80
Make a selection FVD50399701MM Louvers slats they are such a unique feature, so important. By opening the front fenders, and allowing the hot air from the brakes to get ventilated out of the wheel arch! To mount on top or bottom of the exist front fender. For all Porsche 997 Carrera | s | 4s | GTS | GT3 | targa | turbo s | GT2 | GT2 rs | sport classic
$640.20
Make a selection FVD3522946993R Genuine rear "big red" brake kit which includes 993 turbo calipers, discs, pads, damping plates, warning contacts and hex head mounting bolts. Please note: this kit requires you to reuse your original emergency brake and dust shield.
$3,681.37
Make a selection FVD351425426EQ A quality, cost effective set of replacement "big red" style calipers. These are a direct replacement for the 965 turbo, 993 c4s / rs and 993 turbo but can be installed on many 964 / 993 models with the correct caliper adapters. Please contact your FVD parts specialist for fitment questions. We also recommend swapping out your brake lines for a set of stainless braided lines when replacing calipers. Also a now is the time to install a set of our speed bleeders, part # FVD910102. They are comparable to part numbers 993 351 425 10 and 993 351 426 10. Please note: these are aftermarket calipers and do not come with the logo or brake pads. Sold individually. 1 necessary per car.
$874.50
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |