PORSCHE 964 SPACERSCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 356 1960-65 - Engine (includes uncategorized and accessory items) 53910210600 Spacer in front of steel gear all 356 & 912. View/Change Diagram
From $46.23
Make a selection 54705262 View/Change Diagram
$1.34
Make a selection 61607807 Known as: intermediate piece View/Change Diagram
From $17.71
Make a selection 369021071 Flywheel spacer .8mm all 356 & 912 (except super 90). Use only one flywheel spacer to achieve proper crankshaft end play. View/Change Diagram
$39.00
Make a selection 90010200102 Sleeve, 2 req'd for 356 up to early 356a, 3 req'd for late 356a to 912 View/Change Diagram
From $1.00
Make a selection 61610216105 Flywheel spacer 3.05mm for super 90. Use only one flywheel spacer to achieve proper crankshaft end play. Special order item. View/Change Diagram
$109.95
Make a selection 53905237 Known as: thrust washer / thrust washer 0,6 mm View/Change Diagram
From $5.86
Make a selection 61610216301 Sealing washer for crank pulley. All 356 & 912. View/Change Diagram
From $5.34
Make a selection 61610531200 Known as: spacer rocker shaft View/Change Diagram
$15.40
Make a selection 61610612500 Known as: spacer ring View/Change Diagram
From $5.90
Make a selection 369021074 Known as: thrust washer / thrust washer 0,95 mm View/Change Diagram
$38.19
Make a selection 61610080500 Known as: support View/Change Diagram
$14.17
Make a selection BBI9964010004 Features
$795.00
Make a selection
$55.21
Make a selection 369021073 Known as: thrust washer / thrust washer 0,90 mm View/Change Diagram
$38.19
Make a selection FVD347964993 If you are running 17" or 18" wheels, this is a must. It limits the steering angle so that the tires will not rub the chassis. It mounts on the inner tie rod nearest the steering rack. This is a direct replacement / alternative for Porsche part # 964 347 325 02. Made in Germany. Sold individually. 2 necessary per car.
$20.90
Make a selection BBI9964010002 Finally, a complete solution to properly widen the front track width of a Porsche 996 and 997 turbo. To help increase front end grip, this kit allows full negative camber adjustment without binding the axles and fitment of wider wheel/tire combinations and GT3 cup car fenders. Each kit includes lower control arms, thrust arms, axle spacers, upper mounts, and camber shims.
$3,695.00
Make a selection 369021075 Known as: thrust washer / thrust washer 1,00 mm View/Change Diagram
$36.31
Make a selection BBI9964010006 Finally, a solution that allows you to safely increase without the risk of damaging your front axles. as you add GT3 shims to your front Porsche 996/997 turbo lower control arms, you move the cv joints beyond their safe range of motion, risking failure and expensive damage. These 10mm thick precision spacers, used with 16mm of lca shims will provide an additional -1.7 deg. Of camber, while maintaining the factory cv joint and axle relationship. the spacer design features a concentric lip that positively and accurately locates it to the cv joint for perfect balance and no vibration. Each kit includes two spacers and all the needed hardware in high class 10.9 grad
$375.00
Make a selection 36905719 Known as: thrust washer / thrust washer 0,6 mm View/Change Diagram
From $5.78
Make a selection 369021072 Flywheel spacer .85mm all 356 & 912 (except super 90). Use only one flywheel spacer to achieve proper crankshaft end play. View/Change Diagram
$40.00
Make a selection 61610844100 Fuel pump block (fiber spacer). View/Change Diagram
From $29.80
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |