PORSCHE 986 HARDWARECan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 911 1965-69 - Brakes/Wheels (includes uncategorized and accessory items) BBI9964010006 Finally, a solution that allows you to safely increase without the risk of damaging your front axles. as you add GT3 shims to your front Porsche 996/997 turbo lower control arms, you move the cv joints beyond their safe range of motion, risking failure and expensive damage. These 10mm thick precision spacers, used with 16mm of lca shims will provide an additional -1.7 deg. Of camber, while maintaining the factory cv joint and axle relationship. the spacer design features a concentric lip that positively and accurately locates it to the cv joint for perfect balance and no vibration. Each kit includes two spacers and all the needed hardware in high class 10.9 grad
$375.00
Make a selection BBI9918170001 If you have the optional sport bucket seats and planning to install 6-point race harnesses, then you will need this bracket. Without any modifications, this bracket bolts directly to the seat and keeps the harnesses at the proper 10-20° angle regardless of the seat position.
$250.00
Make a selection AP9972TT170 The stock exhaust of the Porsche 997.2 turbo is very restrictive compared to aftermarket systems. Porsche does this to meet sound and emission purposes like most OEM manufacturers. agency power set out to create an exhaust system for the new Porsche 997.2 turbo 6speed or pdk that did not drone, would produced amazing performance, and under throttle give an incredible sound. we have accomplished this! the new agency power exhaust not only saves about 30lbs off the rear end, it also improves power quite a bit.
$3,749.95
Make a selection AUTA2050 Universal power antenna w/chrome mast; includes mounting hardware and electrical connectors; can be installed on vehicles with 0-30 degree body slopes
$62.56
Make a selection 98650499401XXX Speedster covers add a more aerodynamic look to your Boxster. Made of molded fiberglass. Installation hardware included. Easily removable. Specify paint code from your car.
$1,899.40
Make a selection FVD105911930 This kit contains everything needed for a valve adjustment. High-quality victor reinz gaskets with hardware, designed to perform like the original. We source this kit in Germany to ensure quality, reliability and precise fitment. Set includes: 2 qty. Lower valve cover gaskets 93010519507 2 qty. Upper valve cover gaskets 93010519404 2 qty. Oil strainer / sump plate gaskets 93010139101 2 qty. Sealing rings 90012311830 8 qty. M6 nuts 8 qty. Chain case washers 34 qty. Valve cover nuts 34 qty. Valve cover washers sold as a set. 1 necessary per car. Please note: please check the model fitment tab to ensure accurate fitment.
$71.18
Make a selection BES99305040S FVD is proud to introduce our newest line of Brombacherexhaust systems. Brombacher exhausts are engineered for the discerning Porsche owner and offer unmatched performance, unparalleled quality, and incredible value. All of our exhausts are manufactured in Germany and are tested comprehensively for flow rate and characteristics, thermal stress, resistance to cracking, and longevity. Brombacher mufflers outer shell dampens and eliminates unwanted frequencies and ensures no resonance or drone in the cabin. The end result is a strong, linear, firing-order dominated flat-6 Porsche sound. In addition, Brombacherexhausts systems are available for ultimate performance full titanium. Our titanium system's are nearly...(choose a part on the right to read more)
$1,820.50
Make a selection
From $63.23
Make a selection 129PR801840 The rh speedline style wheel is a period correct replica for any air-cooled Porsche model. It is a three-piece modular wheel with a cast center and spun aluminum inner and outer barrels. The center is painted in a silver metallic paint and clear-coated for a durable shine. The inner barrel is silver anodized while the outer lip is high-polished and then clear coated to protect the shine for a maintenance free finish. The wheel also features a hub-centric 71.6 mm (2.82 inches) center bore to ensure a vibration free ride. The wheel accepts original mounting hardware along with the original center cap. The wheel is shipped with a metal valve stem and rh center cap. German-made and TUV approved. Sold individually.
$970.20
Make a selection BES99105040S Perfect muffler for those looking for a more aggressive exhaust note without changing the factory catalytic converters. The added benefit is you can reuse your OEM catalytic converters for emissions purposes. + 15 hp & + 12 torque - reuses OEM cats, perfect for those concerned about warranty. - open muffler design for added power. - tubing diameter is the same as the OEM system. - weighs 19 lbs. (8,6 kg) - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - 4 on a scale of 1-10 in volume (1 being stock) below 3,000 rpms, 6 on a scale of 1-10 in volume under maximum load (3 being stock). - includes cone and v band style hardware to prevent exhaust leaks. - made in Germany. - modular desi...(choose a part on the right to read more)
$2,920.50
Make a selection 91163193301EQ This is the inner headlight ring that retains the adjustment and securing screws. This part is "resi-coated" and includes all mounting hardware. Sold individually. Driver's and passenger's side fitment. 2 necessary per car.
$93.50
Make a selection BES99722040S81 Brombacher 997.2 tt "sport stock" stainless steel, cat bypass for OEM muffler facts: - + 21 crank hp & + 18 crank torque** - reuses OEM muffler, perfect for those looking for more sound and power. - tubing diameter is the same as the OEM system. - weighs 19 lbs. (8,6 kg) - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - reduces backpressure and thermal stress - 6 on a scale of 1-10 in volume (1 being stock). - reuses OEM v band style connecting hardware. - made in Germany. - available in 100 cell or 200 cell. Please ask your sales person for pricing. - more distinguished growl at idle, partial throttle and wide open throttle. - dme programmin is necessary. - reuses OEM tips. FVD i...(choose a part on the right to read more)
$859.10
Make a selection 129PR851821 The rh speedline style wheel is a period correct replica for any air-cooled Porsche model. It is a three-piece modular wheel with a cast center and spun aluminum inner and outer barrels. The center is painted in a silver metallic paint and clear-coated for a durable shine. The inner barrel is silver anodized while the outer lip is high-polished and then clear coated to protect the shine for a maintenance free finish. The wheel also features a hub-centric 71.6 mm (2.82 inches) center bore to ensure a vibration free ride. The wheel accepts original mounting hardware along with the original center cap. The wheel is shipped with a metal valve stem and rh center cap. German-made and TUV approved.
$999.90
Make a selection FVD3522C28007A This line is dedicated to the most demanding customers. This braking system originates from the racing components, consisting of a ventilated, integral or composite disc, aluminum calipers, a complete set of high-performance brake pads, TUV/dot homologated metal-braided brake hoses and high-quality fastener hardware. Features: proven on-track performance; extraordinarily powerful and consistent under the repeated loads. Disperses gasses, cleans pads for better "bite". 2 piece rotors reduce "un-sprung weight" at each corner for better handling. Provides maximum braking force without the flex of sliding calipers. Reduces heat-related stress, increases brake performance and pedal feel. Aggressive pads that las...(choose a part on the right to read more)
$3,954.50
Make a selection FVD362999K3 Center locking conversion kit central locking device for fast wheel changes on the racetrack. Kit includes: - center locking system - removal key and hardware - brake disk connecting parts for centerlock tech info: you need central locking wheels ! Professional installation required.
$5,492.30
Make a selection FVD375003 Are you experiencing vibrations in the cabin? The most likely cause is a worn transmission mount. Severely worn mounts translate to engine component wear and can even cause difficulty shifting. Our mount is manufactured in europe by an OEM supplier using the finest materials. It is a 65 shore rubber hardness value which is the same as the what was standard on these cars. Be sure to swap yours out during your next service. Sold individually. Central fitment in transmission carrier 96437502301. 1 qty. Required. Tech tip: now is the time to replace the old hardware as well. Below is a list of what is needed for installation. 1 qty. Hex head bolt m10x100 90007429202 1 qty. Lock nut m10 49020001 2 qty. Washers 10.3x...(choose a part on the right to read more)
$165.00
Make a selection FVD3522P18056A The brembo gran turismo (gt) braking system is ideal for use on the street and for light track use. This GT system expands upon the original drilled disc's face type made by Porsche. The cross drilled disc surface continuously refreshes the braking surface and offers the highest initial response of any disc type. So, you can confidently respond to sudden pedestrian or traffic movement with maximum braking performance. Drilled discs operate in a wide range of operating temperatures and environments and respond confidently in wet weather. The GT line is dedicated to the most demanding customers. It originates from racing components, consisting of floating ventilated cross drilled discs, aluminum calipers with op...(choose a part on the right to read more)
$4,064.50
Make a selection FVD3511M39040A2 The brembo gran turismo (gt) braking system with type iii rotors is ideal for ideal for clubsport and sprint type track events. It utilizes brembo type iii aggressive face-type discs that offer high initial response with a smooth pedal feel. The type iii offers the highest overall braking confidence and control, allowing a quick qualifying time or top results in sprint races. The GT line is dedicated to the most demanding customers. It originates from racing components, consisting of floating ventilated cross drilled discs, aluminum calipers with opposed pistons, a complete set of high-performance brake pads, abrasion and corrosion resistant goodridge braided steel brake lines and high-quality fastener hardware...(choose a part on the right to read more)
$5,054.50
Make a selection FVD3511M19004A The brembo gran turismo (gt) braking system is ideal for use on the street and for light track use. This GT system expands upon the original drilled disc's face type made by Porsche. The cross drilled disc surface continuously refreshes the braking surface and offers the highest initial response of any disc type. So, you can confidently respond to sudden pedestrian or traffic movement with maximum braking performance. Drilled discs operate in a wide range of operating temperatures and environments and respond confidently in wet weather. The GT line is dedicated to the most demanding customers. It originates from racing components, consisting of floating ventilated cross drilled discs, aluminum calipers with op...(choose a part on the right to read more)
$5,054.50
Make a selection FVD3511M39040AS The brembo gran turismo s (gt-s) braking system is ideal for clubsport and sprint type track events. The GT-s type iii system utilizes brembo type iii aggressive face type discs that offer high initial response with a smooth pedal feel. The type iii offers the highest overall braking confidence and control, allowing a quick qualifying time or top results in sprint races. Gt-s systems contain advanced calipers that include racing style radiators, dual inner piston seals, an inner pressure seal and an outer wiper seal. This innovative design provides the best combination of performance and long-lasting track use. The calipers are hard anodized in black (machined brembo logo in red) for resistance to corrosion and...(choose a part on the right to read more)
$5,164.50
Make a selection FVD900012 Protect your car from steep driveways and parking blocks. Weighs 4.91 lbs (2.23 kg). Includes all necessary hardware. Made in Germany please note: this requires holes to be drilled into the support.
$313.23
Make a selection FVD51299102MM The moshammer vented rear diffuser with fins is an aggressive design that reduces aerodynamic drag. This vented diffuser allows air that is trapped by the rear bumper to exit, allowing for greater top end performance. The design also incorporates 5 fins that improve laminar airflow by reducing turbulence. Moshammer manufactured this as a direct replacement, so it secures seamlessly to the factory locations with the original hardware. This is an ideal addition for a leased vehicle or for those looking to return the car to its original appearance in the future. When added to other elements of the downforce rs (991.1 turbo/s) package, the result is a confident, cohesive stance with balanced downforce. Features: ve...(choose a part on the right to read more)
$1,460.80
Make a selection FVD51299124MM The moshammer stormforce evo rs rear spoiler for the 991.2 model blends a bit of Porsche ducktail heritage into its design to increase rear downforce and reduce front axle uplift. The contours of this spoiler have a step effect which seamlessly blends into both rear quarter panels. When viewed at a standstill it has a subtle factory like appeal that complements the cars lines. When deployed the rake angle takes on a more aggressive appearance evoking thoughts of the much beloved ducktails. Like a majority of the moshammer offerings, this spoiler is a direct replacement, so it secures seamlessly to the factory locations with the original hardware. This is an ideal addition for a leased vehicle or for those looki...(choose a part on the right to read more)
$1,455.30
Make a selection FVDBRO906539 This disc is a genuine brembo replacement part. It is slotted and vented. Sold individually. Be sure to purchase the correct disc assembly hardware kit, FVD part # FVDbro915506.
$625.90
Make a selection FVDBRO1016003A Weight savings approximately 4kg (8.8 lbs) of rotating unsprung weight. Oem disk weight 10,8kg (23.8 lbs), brembo disk weight 8.9kg (19.69 lbs) rotors: (13") 330x34mm drilled discs bells / hats: precision milled billet aluminum hardware: brembo floating anti-rattle disc hardware by using an aluminum bell for the hub section of the disc, these rotor assemblies save a great deal of weight. Since this is both rotating and unsprung, it benefits the acceleration, braking, and handling of the vehicle. Secondly, it is better able to handle the large temperature changes that a brake disc experiences. The mounting system is designed to allow a specific amount of float in both radial and axial directions. Brembo has eng...(choose a part on the right to read more)
$1,815.00
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |