Vehicles
Sections
61 not categorized PORSCHE 996 RUBBER BUSHINGCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 911 1965-69 (includes uncategorized and accessory items) 90133105900 Replace worn-out rear trailing arm bushings with this OEM bushing, made of rubber with a 65-shore hardness value. 65-shore is what was originally used in all of the OEM bushings, it is quiet and comfortable for street use with street suspension. If you are looking for something sportier, try our rs bushing set, made of rubber with an 85-shore hardness value, our part # FVD33105900 sold individually. 4 necessary per car. View/Change Diagram
From $25.50
Make a selection 993014340 Your suspension is only as good as the bushings. Over time, factory rubber bushings deteriorate, allowing the suspension to become loose and sloppy. Daystar poly graphite bushings last years longer than standard bushings, and bring back suspension performance. Available in performance, which are much stiffer and race-ready. Set of 4 bushings for the front and rear of the front a-arms. General Fitment911 1965-69911 1970-73 911 1974-77 930 1975-77 911 1978-83 911 1984-86 911 1987-89 912 1965-69 914 1970-76
$31.89
Make a selection 90134142103 High-quality OEM replacement made with original rubber (65 shore hardness value). The bushing cartridge is crafted in high carbon steel and 7075 t6 aircraft aluminum. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. Driver's or passenger's side fitment. 2 necessary per car. View/Change Diagram
From $65.00
Make a selection 90134379202
View/Change Diagram
From $7.57
Make a selection 90162892301 This is the female of the two required bushings per wiper shaft. easily installed with the rack removed. View/Change Diagram
From $15.81
Make a selection 91133300900B Bushings set with instructions:w/ 55-60 shore a
$29.89
Make a selection 935FSUSP This light weight, bolt in kit replaces the factory front suspension arms, cross-member, and rubber bushings when converting to a coil over front suspension system. General Fitment911 1965-69911 1970-73 911 1974-77 930 1975-77 911 1978-83 911 1984-86 911 1987-89 914 1970-76
$1,850.00
Make a selection 96433102100RATK Unsure about installing a replacement bushing? Send us your trailing arm and we will properly recondition and install the bushing for you. The reconditioning process includes full inspection of your trailing arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we properly install our rear clubsport trailing arm bushings, part # FVD3310212291. Our rear trailing arm bushings contain rubber inserts with a shore hardness value of 85, like what is used on rennsport models. They offer rs style handling characteristics, superior durability and are still forgiving enough for street use. When reconditioning the trailing arms, we als...(choose a part on the right to read more)
$672.10
Make a selection 96434101807AT By ordering this article number, you will receive a reconditioned wishbone with newly pressed-in bearings. The calculated replacement deposit will be returned to you as soon as the old part has been received and checked. This item is also available with race bearings (85 shore).article number FVD 341 018 07at the reconditioning process includes full inspection of each track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we properly install our OEM front control arm bushings, part # FVD3419991. They are made with 65 shore rubber like the original control arms. If your old part is not repairable we will inform y...(choose a part on the right to read more)
$418.00
Make a selection 96437504381 Replace your worn-out, original soft rubber engine mounts with our higher density, rs specification rubber bushing. This is manufactured of rubber with a 75-shore hardness value. 75-shore is the same density as what is used in the rs models. It is more durable, provides more positive, sharper shifts and offers crisper throttle response. Yet, rs spec rubber is still quiet and comfortable for street use. Features: sharper shifts crisper throttle response does not produce nvh (noise vibration harshness) like teflon or solid bushings rubber has a shore hardness value of 75 (like rs models) made in Germany this mount is a high-quality OEM (original equipment manufacturer) replacement part, designed to perform like t...(choose a part on the right to read more)
From $199.99
Make a selection 90133300309B This rear spring plate is manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. New OEM spec. (65 shore) rubber bushings are installed to make this a direct bolt on. Features: made from ¼ inch spring steel includes new OEM spec. (65 shore) rubber bushings made in Germany sold individually. Left or right-side fitment. 2 necessary per car.
$306.90
Make a selection FVD3310212291 Our rear trailing arm bushings contain rubber inserts with a shore hardness value of 85, like what is used on rennsport models. It offers rs style handling characteristics, superior durability and is still forgiving enough for street use. - better handling. - makes precision adjustments of the suspension easier. - does not produce road noise. - shore hardness value of 85. - direct OEM replacement. - more forgiving for street use. -includes press tools and grease for easier assembly. Sold as a set. 1 kit is necessary per car. Please note: this fits the 964 c2 / c4 and rs america. Not keen on installing or having the bushings installed at a shop? Please check out our part # FVD33399603b8 and FVD33399603b8, we wil...(choose a part on the right to read more)
$902.00
Make a selection ER2011000 Monoballs deliver precise, razor sharp handling. but rapid wear has made them impractical for all but the most serious racers. Not anymore! Weather seals - our proprietary-design monoball cartridges have weather seals to keep dirt out and extend product life. this is the only monoball suitable for street or extended track use. dirt and water contaminate ordinary products and accelerate wear. Performance - today’s sticky tire compounds generate corner loads that easily compress factory rubber bushings causing wandering alignment settings. Camber and toe flop around upredictably. weather-sealed monoball cartridges replace compliant factory rubber bushings with hardened-steel spherical bearings. Unlike...(choose a part on the right to read more) General Fitment914 1970-76911 1987-89 911 1984-86 911 1978-83 930 1975-77 911 1974-77 911 1970-73 911 1965-69 912 1965-69
$299.95
Make a selection FVD33150001 Solid bushings and mounts allow you to achieve exact suspension articulation which improves handling and stability on lowered / race prepared cars. The original soft rubber bushings can deform under track loads which allows the sub frame to shift and throw the camber and toe off. Solid bushings will not deform and will keep the camber and toe settings in line which equates to confidence in cornering and faster lap times. These are intended to replace the soft rubber bushings on the original rear sub frame (part #'s 993 331 051 00 & 993 331 052 00). They are made in Germany and are TUV approved. Sold as a set. 1 set is necessary per car. Please note: if you are also driving your car on the street, they will res...(choose a part on the right to read more)
$243.10
Make a selection FVD33105900 Replace worn-out rear trailing arm bushings with our FVD sport bushings, made of rubber with an 85 shore hardness value that is the same as the rs models. 85 shore is more durable, provides more positive suspension location and is still quiet and comfortable for street use. This is a direct replacement for original part # 90133105900 features: better handling makes precision adjustments of the suspension easier does not produce any noise like the teflon bushings. Rubber has a shore hardness value of 85 (like rs models) fit's like oem, simple installation made in Germany set is sold per axle. 1 necessary per car.
$154.00
Make a selection FVD33300902AT Send us your original spring plate and we will have it reconditioned for you. The reconditioning process includes full inspection to ensure proper operation after the remanufacturing process. We then disassemble, degrease and media blast the part. Once fully prepared, we install new rs spec. (85 shore) rubber bushings/bearings. 85 shore rubber is more durable than OEM 65 shore and provides more positive suspension location yet is still quiet and compliant for street use. Then we seal the spring plate with a corrosion resistant plating. Sold individually. 2 necessary per car. Please note: this only fits cars with the g50 transmission.
$261.80
Make a selection FVD33150005 Restore proper suspension geometry with this adjustable lower rear control arm. The factory control arm cannot compensate enough when lowering your Porsche, leaving you with as much as ½ inch of toe in. The result is poor handling and rapid tire wear. This kit will provide the additional adjustment needed. The adjusting link has a left and right hand thread on each end. Rotating the link will increase or decrease the overall length of the arm. A precision teflon lined spherical rod end replaces the compliant rubber factory bushing for improved suspension response and feedback, and also reduces toe changes during acceleration and deceleration. Sold in pairs. 1 necessary per car.
$764.50
Make a selection FVD33150045R Replace worn-out soft rubber (65 shore hardness value) control arm bushings (camber link and caster link) with sportier rubber (75 shore hardness value) that is more durable, provides more positive suspension location and is quiet and more forgiving than a monoball upgrade. This bushing cartridge is weather sealed and is crafted in high carbon steel and 7075 t6 aircraft aluminum. Sold individually.
$69.30
Make a selection FVD33150046R Replace worn-out original soft rubber (65 shore hardness value) track rod bushings with our FVD clubsport series. They are made of rubber that has an 85-shore hardness value, the same as the rs models. 85-shore is more durable, provides more positive suspension location and is quiet and more forgiving than a monoball upgrade. This bushing is made in Germany, weather sealed, crafted in high carbon steel and 7075 t6 aircraft aluminum and includes an 85-shore hardness value core. Sold individually. 8 are necessary per car. Please note: this does not include the track rod, the picture circled in red is just for reference.
$66.00
Make a selection FVD33150003 Rear toe control arms - order in pairs only restore proper suspension geometry with this adjustable lower rear control arm. The factory control arm can't compensate enough when lowering your Porsche, leaving you stuck with as much as ½ of toe in. The result is poor handling and rapid tire wear. This kit will provide the additional adjustment needed. The adjusting link has a left and right hand thread on each end. Rotating the link will increase or decrease the overall length of the arm. A precision teflon lined spherical rod end replaces the compliant rubber factory bushing for improved suspension response and feedback, and also reduces toe changes during acceleration and deceleration.
$218.90
Make a selection FVD33391101SET These bushings are manufactured from higher density, rs specification rubber (85 shore). Rs bushings are more durable than OEM 65 shore, provide more positive suspension location and are still quiet and compliant for street use. This set is a direct replacement for original part # 911 333 009 00 sold as a set. 1 necessary per axle.
$108.90
Make a selection FVD34101807ATK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will properly install our FVD clubsport front control arm bushings, part # FVD341999r. They are made with 85 shore rubber (like the rennsport model). Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrangements can ...(choose a part on the right to read more)
$418.00
Make a selection FVD34101802ATK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will properly install our FVD clubsport front control arm bushings, part # FVD341999r. They are made with 85 shore rubber (like the rennsport model). Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrangements can ...(choose a part on the right to read more)
$418.00
Make a selection 99333105180 The bushings are made of rubber with an 85-shore hardness value, which is more durable, provides more positive suspension location and is still quiet and comfortable for street use. Sold individually.
From $764.50
Make a selection FVD34391192SET Replace worn-out original front lower control arm bushings with our FVD sport bushings, made of rubber with an 85 shore hardness value that is the same as the rs models. 85 shore is more durable, provides more positive suspension location and is still quiet and comfortable for street use. Features: better handling reduces that sloppy steering feel makes precision adjustments of the suspension easier does not produce any noise like the teflon bushings. Rubber has a shore hardness value of 85 (like rs models) fit's like oem, simple installation made in Germany set is sold per axle. 2 necessary per car.
$158.40
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |