PORSCHE 964 EMSCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 911 1970-73 - Body (includes uncategorized and accessory items) FVD641102105SOBR01 Check-engine light position top right. Like new
$63.80
Make a selection FVD375003 Are you experiencing vibrations in the cabin? The most likely cause is a worn transmission mount. Severely worn mounts translate to engine component wear and can even cause difficulty shifting. Our mount is manufactured in europe by an OEM supplier using the finest materials. It is a 65 shore rubber hardness value which is the same as the what was standard on these cars. Be sure to swap yours out during your next service. Sold individually. Central fitment in transmission carrier 96437502301. 1 qty. Required. Tech tip: now is the time to replace the old hardware as well. Below is a list of what is needed for installation. 1 qty. Hex head bolt m10x100 90007429202 1 qty. Lock nut m10 49020001 2 qty. Washers 10.3x...(choose a part on the right to read more)
$165.00
Make a selection FVD641102105WOBR01 Check-engine light position top right. Like new
$63.80
Make a selection G64641102103SIR01 Like new
$25.30
Make a selection RES96400100S1 More low and mid-range torque than our race system with cat bypass. Larger primaries, larger collector, largest diameter tubing on the market. Made for mid-range and top end performance with the added beauty of dual exhaust tips! + 25 hp & + 23 torque - 100 cell hjs tri-metallic race catalytics. -2 1/2 tubing (63.5mm) for max. Power across the rpm range.* -weighs 49 lbs. (22 kg). -German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - aeroquip cone style catalytic connection design to prevent exhaust leaks. -includes aeroquip quick release clamps. -made in Germany by m&m exhaust, gmbh. -dual round 3 exhaust tips -intoxicating flat 6 growl at idle, partial throttle and wide open throttle. P...(choose a part on the right to read more)
$7,403.00
Make a selection G64641102104R01 Like new
$47.30
Make a selection 22011090102ATK Sport throttle bodies are a great addition for those with highly modified cars. They are a great addition for those with full exhaust systems (larger diameters), maf kits, larger displacements, street or race cams, etc. The remanufacturing process includes full inspection of your throttle body to ensure proper operation after the remanufacturing process. We then disassemble and bore the original to a 2.7-inch (70.5 mm) diameter. The entire throttle body is cleaned, degreased and the internals are polished to create more laminar flow. We then machine the shaft to accept larger butterfly's which seamlessly match the bore. All clearances are checked for precision to ensure reliability. Each throttle body is reman...(choose a part on the right to read more)
$589.60
Make a selection RES96400000S1
$5,674.90
Make a selection 100555112NB German lightweight sliverknit rear seat delete / rear shelf carpet that was used on the 964 and 993 rennsport models. We go to extra lengths to ensure that our carpets are made as closely to the originals as possible. Each carpet is made with original lightweight German sliverknit and are trimmed in vinyl. Each is cut, sewn and trimmed to fit perfectly. Made in Germany. Sold individually.
$1,151.70
Make a selection 10050330000 This 9 inch front and 11 inch rear steel fender flare set is made in Germany, we offer a complete line of replacement bodywork to complement the entire Porsche model range. Sold individually. 1 necessary per car. Please note: for conversions, these flares will allow you to run 9 wide tires in the front and 11 wide in the rear. For the 964 / 965 models the torsion bar cut out must be filled. Due to variances in production at the factory, age, accident damage or rust, each part may require trimming and or adjustment for perfect fitment.
$1,648.90
Make a selection 115900964BI01 Bilstein b16 (pss10) suspension kits feature ride height adjustability with 10-stage manually adjustable dampers. Simply adjust compression and rebound settings, from comfort to competition, by rotating the setting number knob at the base of the shock. The front and rear progressive rate springs allow accurate adjustment of the vehicle ride height and center of gravity for the level of performance you seek. Ride height is adjustable from 1.0 to -1.5 20-40mm (front) & -1.0 to -1.5 20-40mm (rear - minimum 1 lowering). Bilstein b16 (pss10) suspension allows you to enjoy the kind of precise suspension tuning formerly available only on race cars. We recommend purchasing our lowering collar kit if you plan to run the...(choose a part on the right to read more)
$3,855.50
Make a selection 21011196402 Say good bye to the days of having to weld and cut aftermarket sport cats to make them fit! We have our sport cats made in Germany to our specifications and that means that these are 100% bolt on without issue! - + 10 crank hp & +6 crank torque. - 200 cell, tri metallic German hjs sport catalysts. - large volume o 105 mm (4.1 inch diameter) high flow cat. - exhaust hanger brackets are included so that the heat shield does not have to be removed. - weighs 7.2 lbs. (3,2 kg). - direct bolt on replacement. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - reduces backpressure and thermal stress. - made in Germany. - more distinguished flat 6 growl at wide open throttle. The FVD 200 cell...(choose a part on the right to read more)
$1,593.90
Make a selection 96410524707GU This fits 964 c2 / c4 and rs models with engine codes # m64.01/02/03. This is an OEM part, sourced directly from Germany. Professional installation is required. Different manufacturing tolerances require an inspection of the free clearance of all parts! If you're not sure about what parts are right for your build, be sure to ask one of our parts specialists. Sold individually. 1 necessary per car.
$932.80
Make a selection 364954 Gurtwinkel ( zum befestigen des gurtschlosses) ist 96452106500 und 3x 99902523103 . Pro sitz 1x den gurtwinkel und 3x die unterlagsscheibe zum ausgleichen . General Fitment911 1994-98911 1989-94 911 1970-73
$181.98
Make a selection FVD55259100 High quality polished carbon dash trim piece. Great detail is taken to attempt to match the original weave size, color and polish. Whether you are adding carbon to the interior or matching existing pieces, this is high quality and is made in Germany so it is made to last, like the original. This cover is a carbon replacement for original # 964 552 231 01 01c. Sold individually.
$81.40
Make a selection 91173103217CA9 Finally a top quality sunvisor for the 911 that you will be proud to display at the next concours competition! an accurate reproduction of the early, late, or targa cars complete with the expensive sunvisor clip as well. we were very happy to contract with a firm overseas to produce an exact match to the original sunvisors installed in your early 911 912 and targa. as you know all have been superseded to the expensive non matching 964 model visors! (what was Porsche thinking?) now for a fraction of the price you can have exact match new visors, complete with clips that you will be proud of installing, and the concours judges will not remove points! View/Change Diagram
$158.47
Make a selection 96450204200EQ Quality replacement part for original number, 964 502 041 00 grv. This is made by dansk, they offer a complete line of replacement bodywork to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality, factory fitment and performance you expect for your Porsche. This commitment has made dansk one of the original equipment suppliers to the Porsche in Germany. The inner mount is adjustable to properly attach / adjust the striker plate. We recommend adding new striker plates and striker plate gaskets, right side striker plate is part # 99353103001 and the gasket is either 90153170323 or 90153170324 depending on what thickness you need....(choose a part on the right to read more)
$107.80
Make a selection 91173103117CC4 Finally a top quality sunvisor for the 911 that you will be proud to display at the next concours competition! an accurate reproduction of the early, late, or targa cars complete with the expensive sunvisor clip as well. we were very happy to contract with a firm overseas to produce an exact match to the original sunvisors installed in your early 911 912 and targa. as you know all have been superseded to the expensive non matching 964 model visors! (what was Porsche thinking?) now for a fraction of the price you can have exact match new visors, complete with clips that you will be proud of installing, and the concours judges will not remove points! View/Change Diagram
$158.47
Make a selection 96410524609GU This fits 964 c2 / c4 and rs models with engine codes # m64.01/02/03. This is an OEM part, sourced directly from Germany. Professional installation is required. Different manufacturing tolerances require an inspection of the free clearance of all parts! If you're not sure about what parts are right for your build, be sure to ask one of our parts specialists. Sold individually. 1 necessary per car.
$932.80
Make a selection 911561051012EQ This is the top outer section of the cabrio top made in Germany with original sonnenland material. It is as close to the original as possible and is cut and trimmed to fit perfectly. Sonnenland material consists of 3 layers, dyed acrylic twill weave top layer, elastomeric rubber inner layer and polyester woven base layer. It provides increased strength against abrasion, increased fade resistance and the tighter woven layers are made for modern electric tops with stronger frames for the 911 and 964. Sonnenland high quality material was originally used by Porsche and other top German manufacturers. Made in Germany. This would replace original part # 911 561 051 012xw sold individually. 1 necessary per car. Only f...(choose a part on the right to read more)
$1,141.80
Make a selection 96434307001SP Replace your old drop links to reduce body roll and rejuvenate your cars handling in the corners. Sport-version with 85 shore 964 c2 only with m030 factory sport suspension sold individually. 1 necessary per car.
$238.70
Make a selection 96434703200SP We are committed to Porsche cars and are very happy to release an outer tie rod that consists of a monoball joint. Until now this was something that was really only available on racing models. Our tie rod will provide you with unequalled steering precision for street and track use. This component is manufactured in europe and contains the finest materials available, high carbon steel and 7075 t6 aluminum. Installation is seamless, this is a direct replacement for the OEM number, 964 347 032 00. This is ideally suited for use with our monoball inner tie rod, part # 96434705805sp for the 964 c2 / turbo look or 965 or part # 96434705804sp for the 964 c4 or rs. Please note: this is not for the wide body. Sold indiv...(choose a part on the right to read more)
$322.21
Make a selection 96410541903EQ When working on your cylinder head, we recommend replacing the valves, valve seat rings, guides, springs, retainers and temperature sensor at the same time to reduce future labor costs. Cost effective, German made exhaust valve for the 964 c2 / c4 and rs that have the m64.01/02/03 motors. Sold individually. 6 necessary per car.
$64.90
Make a selection 96433102200RATK Unsure about installing a replacement bushing? Send us your trailing arm and we will properly recondition and install the bushing for you. The reconditioning process includes full inspection of your trailing arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we properly install our rear clubsport trailing arm bushings, part # FVD3310212291. Our rear trailing arm bushings contain rubber inserts with a shore hardness value of 85, like what is used on rennsport models. They offer rs style handling characteristics, superior durability and are still forgiving enough for street use. When reconditioning the trailing arms, we als...(choose a part on the right to read more)
$672.10
Make a selection 96434101807ATK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we properly install our OEM front control arm bushings, part # FVD3419991. They are made with 65 shore rubber like the original control arms. Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrangements can be made for...(choose a part on the right to read more)
$418.00
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |