Vehicles
Sections
113 not categorized PORSCHE 914 SUSPENSION REARCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 911 1970-73 (includes uncategorized and accessory items) FVD33105900 Replace worn-out rear trailing arm bushings with our FVD sport bushings, made of rubber with an 85 shore hardness value that is the same as the rs models. 85 shore is more durable, provides more positive suspension location and is still quiet and comfortable for street use. This is a direct replacement for original part # 90133105900 features: better handling makes precision adjustments of the suspension easier does not produce any noise like the teflon bushings. Rubber has a shore hardness value of 85 (like rs models) fit's like oem, simple installation made in Germany set is sold per axle. 1 necessary per car.
$154.00
Make a selection FVD33399600B6 Bilstein suspension featuring with upside/down technology. Lowering 35 mm front and 30 mm rear - giving it a GT3 stance
$2,442.00
Make a selection FVD33150005 Restore proper suspension geometry with this adjustable lower rear control arm. The factory control arm cannot compensate enough when lowering your Porsche, leaving you with as much as ½ inch of toe in. The result is poor handling and rapid tire wear. This kit will provide the additional adjustment needed. The adjusting link has a left and right hand thread on each end. Rotating the link will increase or decrease the overall length of the arm. A precision teflon lined spherical rod end replaces the compliant rubber factory bushing for improved suspension response and feedback, and also reduces toe changes during acceleration and deceleration. Sold in pairs. 1 necessary per car.
$764.50
Make a selection BK7033 Re-issue of autobooks manual covering engine, fuel & cooling systems, ignition, heating, exhaust emissions, clutch, transmission, rear axle, suspension, steering gear, brakes, electronics, and bodywork. This is a manual that will help keep 912 on the road. A must for any 912 owner. General FitmentACCESSORY
$32.00
Make a selection FVD33300905 This rear spring plate is manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. New rs spec. (85 shore) rubber bushings are installed to make this a direct bolt on. 85 shore rubber is more durable than OEM 65 shore and provides more positive suspension location yet is still quiet and compliant for street use. Features: made from ¼ inch spring steel includes new rs spec. (85 shore) rubber bushings made in Germany sold individually. 2 necessary per car.
$273.90
Make a selection FVD33399300 A cost effective FVD exclusive combination of bilstein clubsport shocks with a set of TUV certified eibach springs. This suspension kit will lower the front axle to a maximum of 35 mm (1.37 inches) and the rear axle to 30 mm (1.18 inches), like the European rennsport model. The height is adjustable as the dampers are threaded. They are a cost effective solution for clubsport use and will be well mannered on the street. Sold as a complete kit. 1 kit is necessary per car.
$11,872.30
Make a selection FVD33399301 Bilstein suspension featuring with upside/down technology. Lowering 35 mm front and 30 mm rear - giving it a European rs stance
$12,023.00
Make a selection FVD33398701 Bilstein suspension featuring with upside/down technology. Lowering 35 mm front and 30 mm rear - giving it a GT3 stance.
$2,803.90
Make a selection FVD33399602B6 Bilstein suspension featuring eibach springs. Lowering 35 mm front and 30 mm rear - giving it a GT3 stance
$1,930.50
Make a selection FVD341999R Replace worn-out original soft rubber (65 shore hardness value) control arm bushings with our FVD clubsport series. They are made from rubber with a 85 shore hardness value which is the same as the rennsport models. 85 shore is more durable, provides more positive suspension location and is quiet and more forgiving than a monoball upgrade. This is the ideal upgrade for street and light track / clubsport use. This bushing set is made in Germany, weather sealed, crafted in high carbon steel and 7075 t6 aircraft aluminum and includes 85 shore hardness value cores. This is a front and rear bushing for the front lower control arm (wishbone). 2 sets are necessary per car.
$124.30
Make a selection KG5543 Kyb gas-a-just monotube shocks are designed to increase performance and stability of the vehicle’s suspension system. They are made from sturdy material and is the latest concept in ride. This monotube shock delivers additional handling and control as well automatically adjusts to driving conditions. These shocks are a good replacement for the factory units. Sold each, two needed for the rear of your vehicle. General Fitment912 1965-69911 1965-69 911 1970-73
From $48.15
Make a selection 11599702 Non pasm cars - lowers the front 1.0 inch (25 mm) and the rear 1.0 inch (25 mm). Pasm cars - lowers the front .8 inches (20 mm) and the rear .8 inches (20 mm). Targa - lowers the front 1.3 inches (35 mm) and the rear 1.3 inches (35 mm).
$470.80
Make a selection 11599700H Without pasm cars - lowers the front 1.2 inch (30 mm) and the rear 1.2 inch (30 mm). Pasm cars - lowers the front .8 inches (20 mm) and the rear .8 inches (20 mm).
$513.37
Make a selection 115910996032 Bilstein b4 OEM m030 (original m030 suspension) shock absorber set (4 pieces) for cars with lowering springs or cars delivered with factory m030 sport suspension. Nothing is better than the original! The b4 m030 dampers from bilstein are the perfect shock absorber for lowered cars. Facts: - constant damping pressure under load - increased driving stability - increased durability - OEM quality - bilstein gas pressure technology - type/model m030
$1,682.59
Make a selection FVD33300905ATK Send us your original spring plate and we will have it reconditioned for you. The reconditioning process includes full inspection to ensure proper operation after the remanufacturing process. We then disassemble, degrease and media blast the part. Once fully prepared, we install new rs spec. (85 shore) rubber bushings/bearings. 85 shore rubber is more durable than OEM 65 shore and provides more positive suspension location yet is still quiet and compliant for street use. Then we seal the spring plate with a corrosion resistant plating. Sold individually. 2 necessary per car. Please note: this does not fit cars with the g50 transmission.
$312.40
Make a selection 150SPB976 Replace worn-out spring plate bushings with these longer lasting poly-graphite plastic bushings. Poly-graphite is higher density than OEM rubber so suspension components will experience less deflection. It is specially formulated with a graphite lubricant to produce a bearing like action. This includes the inner and outer bushing for the 2-piece adjustable spring plate. Sold individually. 2 necessary per car.
$39.60
Make a selection FVD333505002 996 atmospheric cars only with m030 factory sport suspension
$44.00
Make a selection 115910997006 Bilstein b4 OEM i030 (original i030 suspension) shock absorber set (4 pieces) for cars with lowering springs or cars delivered with factory i030 sport suspension. Nothing is better than the original! The b4 i030 dampers from bilstein are the perfect shock absorber for lowered cars. Facts: - constant damping pressure under load - increased driving stability - increased durability - OEM quality - bilstein gas pressure technology - type/model i030
$2,153.97
Make a selection 115910997003 Bilstein b4 OEM i030 with pasm (original i030 suspension) shock absorber set (4 pieces) for cars with lowering springs or cars delivered with factory i030 sport suspension. Nothing is better than the original! The b4 i030 dampers from bilstein are the perfect shock absorber for lowered cars. Facts: - constant damping pressure under load - increased driving stability - increased durability - OEM quality - bilstein gas pressure technology - type/model i030 with pasm
$2,983.38
Make a selection MB1230 The Porsche 911 came equipped from the factory for high performance cornering -- but some things have changed in the almost 40 years the 911 has been on the road. For one, the rubber suspension bushings that monoballs replace are most likely already worn out or cracked from decades of use. General Fitment911 1987-89911 1984-86 911 1978-83 930 1975-77 911 1974-77 911 1970-73 911 1965-69 912 1965-69
$273.90
Make a selection FVD33300902AT Send us your original spring plate and we will have it reconditioned for you. The reconditioning process includes full inspection to ensure proper operation after the remanufacturing process. We then disassemble, degrease and media blast the part. Once fully prepared, we install new rs spec. (85 shore) rubber bushings/bearings. 85 shore rubber is more durable than OEM 65 shore and provides more positive suspension location yet is still quiet and compliant for street use. Then we seal the spring plate with a corrosion resistant plating. Sold individually. 2 necessary per car. Please note: this only fits cars with the g50 transmission.
$261.80
Make a selection FVD33150045R Replace worn-out soft rubber (65 shore hardness value) control arm bushings (camber link and caster link) with sportier rubber (75 shore hardness value) that is more durable, provides more positive suspension location and is quiet and more forgiving than a monoball upgrade. This bushing cartridge is weather sealed and is crafted in high carbon steel and 7075 t6 aircraft aluminum. Sold individually.
$69.30
Make a selection FVD333505001 Without ( i030 ) sport suspension set contains: - 2 x 993 333 107 01 - 2 x 996 333 105 02 also c4s cabrio with standart suspension
$166.34
Make a selection 99633305146 Bilstein b4 OEM (original equipment manufacturer) replacement shock absorber for your Porsche with standard suspension. The b4 damper from bilstein is the perfect replacement for your Porsche. Facts: - constant damping power under any load - high power reserves for maximum safety - ride like it's the first time, every time - OEM quality - bilstein gas pressure technology
$460.88
Make a selection FVD34391101SET Replace worn-out original front lower control arm bushings to return your car to its intended suspension geometry and steering feedback. Features: better handling reduces that sloppy steering feel does not produce any noise like the teflon bushings. Rubber has the original shore hardness value of 65 (like oem) fit's like oem, simple installation made in Germany if you are looking for a sportier upgrade we suggest our sport lower control arm set, part # FVD34391192set. Set is sold per axle. 2 necessary per car.
$152.90
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |