PORSCHE CAYMAN S CHECK OUTCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 911 1974-77 - Body (includes uncategorized and accessory items) 99310720305EQ Keep harmful contaminants out of your oil stream and engine by replacing your oil filter with every scheduled oil change. Quality German made replacement filter. Sold individually. 1 necessary per car.
$23.10
Make a selection 99320720103EQ Keep harmful contaminants out of your oil stream and engine by replacing your oil filter with every scheduled oil change. Quality European made replacement filter. Sold individually. 1 necessary per car.
$20.90
Make a selection 115910997001 Bilstein b4 OEM (original equipment manufacturer) replacement shock absorber set (4 pieces) for your Porsche with standard suspension (without pasm). The b4 dampers from bilstein are the perfect replacement for your Porsche. Facts: - constant damping power under any load - high power reserves for maximum safety - ride like it's the first time, every time - OEM quality - bilstein gas pressure technology
$2,004.65
Make a selection 964565035017EQ This is genuine targa top material sourced from Germany. It is as close to the original as possible and is cut and trimmed to fit perfectly. We also make sure that there is plenty of material to stretch out the sides so that there are no wrinkles when installed. Sold individually. 1 necessary per car.
$335.50
Make a selection 99663114380 Please note: this is for cup / r models up to 2001. They have the cut out for the clear headlight corner trim. All motorsport and racing parts are special order items. Special order items must be paid for in advance. Special order items are sold on a non-cancelable, non-exchangeable, non-returnable, non-refundable basis and do not carry any warranty. No exceptions.
$335.50
Make a selection 99642101000 No need to buy the entire shaft assembly any longer. Simply replace your worn out piece with our inexpensive high quality flex disc.
$108.90
Make a selection 99333104503ATK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will properly install the bushings. Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrangements can be made for its return to you. We do not offer a core exchange on this part.
$254.10
Make a selection 115971AAR01 Panamera models with optional air suspension utilize four sensors to control the ride height. This is accomplished via the use of a small linkage or link which connects the sensor to the suspension. As the car is raised or lowered, the link moves the sensor up or down sending a signal to the computer telling it how high the car is. When you replace the non-adjustable factory link with this adjustable design, the output of the sensor makes the computer believe that the car is higher than it is. So, the computer will lower the ride height. The simplicity of this setup is that it retains full functionality of the factory system. Be warned, all adjustable lowering links are not the same! These links are machined al...(choose a part on the right to read more)
$324.50
Make a selection 1159029964WD The ohlins road & track suspension gives our customers a true racing experience, with their own cars, without losing comfort when commuting to work. Our unique dual flow valve (dfv) technology allows you to quickly change the stiffness of the shock absorber. When arriving to the racetrack, just turn the golden knob clockwise on the damper to set it in race mode this action changes all four areas in the damper; low and high speed compression and rebound damping. With ohlins road & track coil overs you will experience a car with blistering response times, improved bump absorption and a massive amount of grip to increase the safety when driving your car on the limit. The car will be easier to balance on the edge o...(choose a part on the right to read more)
$5,635.30
Make a selection 11599710 With and without pasm
$548.90
Make a selection 115900993BI The bilstein b16 (pss10) suspension kit is the ultimate race inspired suspension system, delivering unsurpassed driving performance in any situation. This suspension kit puts you in complete control, providing the kind of precise suspension tuning formerly available only on race cars. From a weekend of competition to daily driving, this system provides perfect handling performance for every situation. The manually adjustable damping mono-tube gas shock absorbers feature 10-stage precise compression and rebound settings, from comfort to competition. The bilstein b16 (pss10) suspension kit utilizes debris resistant round threads on these dampers to ensure spring adjustment remains effortless throughout the life o...(choose a part on the right to read more)
$4,341.70
Make a selection 115910987011 Bilstein b4 OEM (original equipment manufacturer) replacement shock absorber set (4 pieces) for your Porsche with standard suspension and manual transmission (without pasm). The b4 dampers from bilstein are the perfect replacement for your Porsche. Facts: - constant damping power under any load - high power reserves for maximum safety - ride like it's the first time, every time - OEM quality - bilstein gas pressure technology
$1,479.60
Make a selection 115910987001 Bilstein b4 OEM (original equipment manufacturer) replacement shock absorber set (4 pieces) for your Porsche with standard suspension (without pasm). The b4 dampers from bilstein are the perfect replacement for your Porsche. Facts: - constant damping power under any load - high power reserves for maximum safety - ride like it's the first time, every time - OEM quality - bilstein gas pressure technology
$1,479.60
Make a selection 115385 If you are looking for added damping performance on the street, the bilstein b6 performance damper is the ideal solution. The product benefits at a glance: optimum adhesion and enhanced stability for daily driving and extreme driving situations. Marked improvement in safety and sportiness without additional spring changes. Increased service life. Bilstein gas pressure technology. Bilstein mono-tube/upside-down technology. Made in Germany. Road-tested and fine-tuned by bilstein. German TUV registration is not required. Sold individually. 1 necessary per car. We recommend adding our lowering spring collars if you would like a lower ride height, our part # 115110016
$640.20
Make a selection 99334101802ATK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will properly install original control arm bushings. . Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrangements can be made for its return to you. We do not offer a core exchange on this part. Sold individually....(choose a part on the right to read more)
$418.00
Make a selection BES91105000S This muffler was specifically designed for a backdate to the st look. It is manufactured for mid-range and top end performance, all without drone inside the cabin. It seamlessly mates to ssi heat exchangers for added performance while keeping the cabin warm in the winter. The muffler is vastly different than the common baffle plated mufflers stuffed with packing material that are common in the aftermarket. Ours are uniquely made with double perforated sound absorption tubes based on the halbgegenstromprinzip (half counter current principle). The acoustic silencer absorption tubes are made in a trapezoidal pattern and are perforated with varying diameters, which isolate and dampen the unwanted frequencies that c...(choose a part on the right to read more)
$2,627.90
Make a selection 99750598390 This is a genuine 997.1 GT3 Porsche motorsports cup spoiler lip. It is a cost-effective replacement for the original GT3 spoilers. It also improves front end downforce. Please be aware that it is lower than the original Porsche spoiler but is far more pliable and more curb friendly. This part is shipped in a smaller box by motorsports to conserve on shipping costs. It is manufactured in polyurethane, so it has memory. Once you receive it just lay it out in the sun for an few hours or slowly and carefully warm it up with a heat gun. Please note: all motorsport and racing parts are special order items. Special order items must be paid for in advance. Special order items are sold on a non-cancelable, non-exchangea...(choose a part on the right to read more)
$239.95
Make a selection 96434703200SP We are committed to Porsche cars and are very happy to release an outer tie rod that consists of a monoball joint. Until now this was something that was really only available on racing models. Our tie rod will provide you with unequalled steering precision for street and track use. This component is manufactured in europe and contains the finest materials available, high carbon steel and 7075 t6 aluminum. Installation is seamless, this is a direct replacement for the OEM number, 964 347 032 00. This is ideally suited for use with our monoball inner tie rod, part # 96434705805sp for the 964 c2 / turbo look or 965 or part # 96434705804sp for the 964 c4 or rs. Please note: this is not for the wide body. Sold indiv...(choose a part on the right to read more)
$322.21
Make a selection BES96405000S1 This muffler produces a glorious flat six race car with low deep tones that reminds us of the 964 cup. It is manufactured in Germany by m&m exhaust, gmbh. This muffler is ideal for anyone who wants a lower deeper tone with more decibels, whether they are just replacing the side muffler or are running cat bypass, sport cats or a cup pipe. + 14 hp (10 kw) & + 15 tq (20 nm) gain. - 2 3/4 tubing (70mm). - weighs 13.8 lbs (6.3 kg) - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - absolutely no drone in the cabin. - does not interfere with emissions. - includes factory style hangars and new aero quip style clamps for simple installation. We recommend replacing your exhaust tip with this u...(choose a part on the right to read more)
$1,438.80
Make a selection BES98115000S This is a forum favorite for the best sound with minimal drone! This muffler really does everything so well. Civilized while cruising, a beast under load and cup car gurgles and crackles off throttle. + 11 hp & + 10 tq gain. - weighs 35.4 lbs - thermal insulation on piping to keep suspension components cool. Withstands up to 2,012 degrees fahrenheit (1,100 degrees celsius). - 2 1/2 tubing (63.5 mm). - 2 x 3.5 (90 mm) round tips. - intoxicating growl at idle, partial throttle and wide open throttle. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - minimal resonance / drone in the cabin (200 rpms worth) compared to the competition's mufflers. This can be verified on the forums like ...(choose a part on the right to read more)
$3,314.30
Make a selection BES981C1200SGT4 - equal length long tube headers with motorsports merge collector. - 200 cell hd German hjs tri metal sport cats. - primary diameter 50mm outer , 47mm inner for the larger 3.8l displacement. - t316 lightweight stainless steel. - reduces thermal stress on the motor. - made in Germany by m&m exhaust gmbh. Please add 2 engine to header gaskets when ordering - 2 qty 997 111 107 31 power: - 981 GT4 / spyder (3.8l) = + 18 crank hp (13kw) & 16 crank torque ( 21 nm) our latest development for the 981 is aimed at those who are looking for more torque in the mid-range, a rich, deep exhaust growl. These headers contain the latest hjs cats, they are nicknamed "hd" for high durability matrix design catalytic converters. T...(choose a part on the right to read more)
$5,780.50
Make a selection 96434705805SP We are committed to Porsche cars and are very happy to release an inner tie rod that consists of a monoball joint. Until now this was something that was really only available on racing models. Our tie rod will provide you with unequalled steering precision for street and track use. This component is manufactured in europe and contains the finest materials available, high carbon steel and 7075 t6 aluminum. Installation is seamless, this is a direct replacement for the OEM number, 964 347 058 05. We also suggest replacing your outer tie rods, we have a uniball option, our part # 96534703200sp or the OEM style, narrow body is part # 96434703200 or wide body is part # 96434703201 (qty. 2 are needed) and now is also...(choose a part on the right to read more)
$207.90
Make a selection 96410524707ST This fits 964 c2 / c4 and rs models with engine codes # m64.01/02/03. This is an OEM part, sourced directly from Germany. Professional installation is required. Different manufacturing tolerances require an inspection of the free clearance of all parts! If you're not sure about what parts are right for your build, be sure to ask one of our parts specialists. Sold individually. 1 necessary per car.
$1,410.20
Make a selection 96453109600EQ This is a genuine door seal that seals the entire door and window frame. As these classics age the original gasket can become brittle and will crack, so it is essential that it is in good order as it keeps moisture out of the cabin. Sold individually. 1 necessary per car.
$215.60
Make a selection 99334703104 If your outer tie rods are worn, you will experience sloppy steering response and knocking / creaking sounds. Your outer tie rods keep the steering centered, so failure can be dangerous and can seriously affect steering control. After replacing the tie rods, you will experience tighter, more precise feedback without noise. Tie rod consists of: 1 qty. Tie rod 1 qty. Hexagon nut (m14 x 1.5) 1 qty. Inner axial joint 1 qty. Lock nut 1 qty. Dust bellows / boot we recommend replacing the right and left side tie rods at the same time. Sold individually. 2 necessary per car.
$216.29
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |