Vehicles
Sections
327 not categorized PORSCHE 356 C PRE ACan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 911 1974-77 (includes uncategorized and accessory items) 99919217350EQ A severely worn a/c belt will no longer be able to grip the pulleys and will start to slip and cause a loud squealing noise when the a/c is turned on. Belts undergo a lot of friction and wear. They are cost effective to change and will keep you're a/c functioning properly. Be sure to follow recommended service and replacement intervals set by Porsche on belts. High-quality OEM Bosch replacement belt, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 1 necessary per car.
$18.70
Make a selection 9A160618101 Oxygen or lambda sensors are critical to your engine's health. If the sensor is faulty you may experience poor gas mileage, rough idling or engine pinging. Replace it with this high-quality Bosch OEM (original equipment manufacturer) replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 2 necessary per car. Please note: be sure to check the "fits these models" tab to make sure that this will work for your model / application.
From $133.10
Make a selection BAT003 Many pre. 1977 Porsche 911's are not equipped with factory oil plumbing (hard lines and thermostat). In this case fitting an oil cooler requires making a hose run from the rear to the front of the vehicle and back. We find the easiest and most cost effective method of plumbing is to duplicate the factory plumbing route using aeroquip hose and fittings with a mocal oil thermostat and oil cooler. The various kits that we offer to accomplish this task include; one of a number of oil cooler options (some are suitable for both fender or front spoiler location), mocal -12 an oil thermostat with mounting bracket, 30 foot length of aqp -12 an stainless braid 3/4" id hose, 30mm metric to -12 an adaptors for the oil ta...(choose a part on the right to read more) General Fitment911 1974-77911 1965-69 911 1970-73
$985.00
Make a selection BAT002 Many pre. 1977 Porsche 911's are not equipped with factory oil plumbing (hard lines and thermostat). In this case fitting an oil cooler requires making a hose run from the rear to the front of the vehicle and back. We find the easiest and most cost effective method of plumbing is to duplicate the factory plumbing route using aeroquip hose and fittings with a mocal oil thermostat and oil cooler. The various kits that we offer to accomplish this task include; one of a number of oil cooler options (some are suitable for both fender or front spoiler location), mocal -12 an oil thermostat with mounting bracket, 30 foot length of aqp -12 an stainless braid 3/4" id hose, 30mm metric to -12 an adaptors for the oil ta...(choose a part on the right to read more) General Fitment911 1974-77911 1965-69 911 1970-73
$925.00
Make a selection FVD721883081 High quality, German made brake bleeder and vacuum pump kit. Ideal for use on brakes, clutches, hvac, bleeding the fuel system or testing vacuum on a turbocharged system. Vacuum can be tested up to 0.9 bar and pressure up to 4 bar. The kit is complete with a variety of hose ends for various connections. Sold individually. General FitmentACCESSORY
From $246.40
Make a selection FVD641102105WUNR01 Check-engine light down left. Like new
$63.80
Make a selection BESKLS001001
$1,189.10
Make a selection FVD641102105WOBR01 Check-engine light position top right. Like new
$63.80
Make a selection 91511600127 Cast iron pressure plate manufactured by zf sachs to original specifications for all 915 transmissions. Direct replacement for the oe pressure plate. Please note: this is only to be used with sprung discs. We always recommend replacing the pressure plate, clutch disc, throw out bearing and starter ring gear at the same time. View/Change Diagram
From $307.32
Make a selection FVD641102105SOBR01 Check-engine light position top right. Like new
$63.80
Make a selection FT24076 Our 911 sanden kits offer many benefits over the original york compressor found on the early 911 and 930 up through 1983. The sanden uses a "wobble-plate" to move five smaller pistons as compared to the york that uses a crankshaft to move two large pistons. The sanden wobble-plate design requires less horse power to turn and is a better match for the condenser area. Our sanden kit uses less engine compartment space and less horse power to turn. You will notice it runs smoother and quieter and improves system efficiency. The sanden compressor and it's mounting bracket bolt directly to the original york sub-plate. You can purchase our sanden kits in four configurations to match your objectives and budget: from...(choose a part on the right to read more) General Fitment911 1978-83930 1975-77 911 1974-77
$735.98
Make a selection FVD721T71N
$104.50
Make a selection FVD7219012MS
$14.30
Make a selection FVD7213365
$79.20
Make a selection FVD721VW402
$127.60
Make a selection FVD64110510901
$73.70
Make a selection FVD721T7EX
$104.50
Make a selection 9A790727506 This tire pressure sensor is made by the original manufacturer to Porsche, huf. It is a good idea to change the valve stem out when changing the sensor. The valve stem is part # 993343018001 huf and major organizations including the tire industry association, recommend the tpms sensor and valve be replaced for: fitting new tires puncture repairs changing rims electronic failure damage during tire service damage by road hazards valve core or nut seizure did you know that the transportation recall enhancement, accountability and documentation) act in the u.s. Requires that 100% of all passenger cars, light trucks, and buses manufactured in the united states after september 2007 be equipped with a tire pressure mo...(choose a part on the right to read more)
From $101.33
Make a selection NLA11601400 Â for adapting later engines to 356a transmissions with unguided throwout bearings Â
$110.79
Make a selection MV8500 Kit includes everything for performing hundreds of automotive diagnostic and mechanical tests. Used for one-person brake bleeding, produces vacuum or pressure at the turn of a switch. Comfortable ergonomic design with one-finger trigger vacuum/pressure release. Durable die-cast metal construction for long life. Pressure and vacuum are created on the squeeze stroke for superior accuracy and control. General FitmentACCESSORY
$85.95
Make a selection
$70.53
Make a selection
$330.00
Make a selection
From $12.19
Make a selection NLA05010 Made in europe to original okrasa specs replaces 36905010 369-05-010
$369.60
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |