Vehicles
Sections
301 not categorized PORSCHE 996 AS WINGCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 911 1974-77 (includes uncategorized and accessory items) 993014340 Your suspension is only as good as the bushings. Over time, factory rubber bushings deteriorate, allowing the suspension to become loose and sloppy. Daystar poly graphite bushings last years longer than standard bushings, and bring back suspension performance. Available in performance, which are much stiffer and race-ready. Set of 4 bushings for the front and rear of the front a-arms. General Fitment911 1965-69911 1970-73 911 1974-77 930 1975-77 911 1978-83 911 1984-86 911 1987-89 912 1965-69 914 1970-76
$31.89
Make a selection 911110904WO Prevent costly air box explosions! Porsche 911 engines from 1973 on have had the bad habit of backfiring upon cold-starting. And blowing a hole in the air box. When this pop valve is installed in the air box and a backfire occurs, the valve will instantly open and release the backfire pressure. Afterwards, the pop valve then automatically closes and the engine continues to run. The air box pop valve conforms to all emission regulations and has no effect on performance or gas mileage. General Fitment911 1974-77930 1975-77 911 1978-83 911 1970-73 911 1965-69
$28.50
Make a selection 98711691325 Tech tip: renew the ims bearing when replacing/renewing the clutch or all 100,000 km.
$521.40
Make a selection BES99102240SHD + 15 hp & + 14 torque - 200 cell high flow, tri metal German hjs "hd" high durability matrix sports catalysts. - can be used with FVD "brombacher" mufflers. - weighs 15.5 lbs. (7.0 kg). - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - made in Germany. - intoxicating growl at idle, partial throttle and wide open throttle. The catalytic converter cores used in this system are the most advanced in the industry. They are produced by hjs in Germany and are a 200 cpsi (cell per square inch) tri-metal design. Tri-metal cats are the freest flowing and environmentally friendly aftermarket cats produced today. Tri-metal catalytic converters are rodium, platinum and iridium coated and per...(choose a part on the right to read more)
$3,293.40
Make a selection 911606105DXATK The warm up regulator is a critical component that performs the following functions: lowers pressure when engine is cold. Absorbs / distributes engine heat. Allows for an additional rich mixture under full load to prevent engine damage. Altitude correction. Send us your original part and we will have it remanufactured for you. We do not offer a core exchange on this part. Each part is remanufactured in Germany, so the lead times can vary between 6-8 weeks. Sold individually. 1 necessary per car.
$744.70
Make a selection 91150534503 This seal tends to suffer from dry rot and degrades with time. Be sure to replace it before metal on metal contact occurs, destroying the paint work and allowing rust to develop. Any of our OEM replacement parts are designed to appear and perform like the originals. We source these parts in Germany to ensure quality, reliability and precise fitment. When servicing the rear bumper, we recommend replacing the bumper shock seals, part # 91150531100 shock bushings, part # 91150522100 and base, part # 91150522001 sold individually. 1 necessary per car. View/Change Diagram
From $15.50
Make a selection 911606105HXATK The cis injection / k-jetronic warm up regulator is a critical component that performs the following functions: lowers pressure when engine is cold. Absorbs / distributes engine heat. Allows for an additional rich mixture under full load to prevent engine damage. Altitude correction. Send us your original part and we will have it remanufactured for you. We do not offer a core exchange on this part. Each part is remanufactured in Germany, so the lead times can vary. Sold individually. 1 necessary per car.
$744.70
Make a selection 91150193500GRV 911 1974-89 floorpan, left side. Galvanized primed painted. One of the most abused part of the 911 are the floor panels. Years of exposure to moisture, salt, sand, and mud often takes a toll on the metal under your feel. If your Porsche floors have seen better days and are showing the ugly signs of corrosion, we have replacement panels. Each one is painstakingly made to duplicate the factory pieces and galvanized for long life. View/Change Diagram
From $401.98
Make a selection 91150193600GRV 911 1974-89 floorpan, right side. Galvanized primed painted. One of the most abused part of the 911 are the floor panels. Years of exposure to moisture, salt, sand, and mud often takes a toll on the metal under your feel. If your Porsche floors have seen better days and are showing the ugly signs of corrosion, we have replacement panels. Each one is painstakingly made to duplicate the factory pieces and galvanized for long life. View/Change Diagram
From $403.56
Make a selection 91150195500GRV Front floor with suspension mounts. Galvanized primed painted. One of the most abused part of the 911 are the floor panels. Years of exposure to moisture, salt, sand, and mud often takes a toll on the metal under your feel. If your Porsche floors have seen better days and are showing the ugly signs of corrosion, we have replacement panels. Each one is painstakingly made to duplicate the factory pieces and galvanized for long life. View/Change Diagram
From $598.40
Make a selection 83340 Our bolt-in roll cages are scca & nasa legal for club racing. Top of the line in fit and construction. General Fitment911 1974-77930 1975-77 911 1978-83 911 1984-86 911 1987-89
$1,308.56
Make a selection 91135104120FSL Frozen slotted rotors are simply the best brake rotors money can buy. Serious drivers-those who tend to cross the finish line first--take their edge where they find it. And a growing number of them have embraced the edge that they’ve found in cryogenically treated brake rotors. Here’s why: they resist cracking, warping and fading; frozen rotors last 2-3 times longer than normal rotors; they stop consistently, lap after lap. Sold each. General Fitment911 1965-69911 1970-73 911 1974-77 911 1978-83 930 1975-77 914 1970-76 924 1986-88 944 1982-85 944 1985-88 924 1980-85
$168.07
Make a selection 91135104120FSR Frozen slotted rotors are simply the best brake rotors money can buy. Serious drivers-those who tend to cross the finish line first--take their edge where they find it. And a growing number of them have embraced the edge that they’ve found in cryogenically treated brake rotors. Here’s why: they resist cracking, warping and fading; frozen rotors last 2-3 times longer than normal rotors; they stop consistently, lap after lap. Sold each. General Fitment911 1965-69911 1970-73 911 1974-77 911 1978-83 930 1975-77 914 1970-76 924 1986-88 944 1982-85 944 1985-88 924 1980-85
$168.07
Make a selection 220512019 Adjustable wing pitch and accepts the 993 grill.
$3,534.30
Make a selection 90150339422 This seal sits on the trailing edge of the front fender at the top just below the windshield. It is also used at the rear fender where it joins the bumper. 4.3 mm in thickness. Sold individually. 4 necessary per car. Driver's or passengers side fitment. View/Change Diagram
From $8.50
Make a selection 021119233A Superb recreation of the original nla timing hole plug, absolutely necessary to keep the cooling air blowing over the engine and not into the engine compartment! View/Change Diagram
From $24.50
Make a selection 22011099706 The 997 turbo ipd "y" pipe was built for the more demanding turbo performance customer. The factory y pipe becomes restrictive when adding substantial power gains. The ipd "y" pipe has larger inlets and an optimized diversion area allowing for even greater power gains. This superior and more efficient design flows 126 more cfm than the factory y pipe delivering the additional power needed to raise the performance bar on any turbo. The ipd "y" y pipe is designed to be a direct replacement of the factory OEM y pipe. There are no modifications or fabrication required for installing the ipd y pipe. This is an easy and straight forward r & r (remove and reinstall) bolt on upgrade. Note: contains everything nec...(choose a part on the right to read more)
$1,094.50
Make a selection 021119955 This is another one of those small sealing washers to insure that all of the cooling air is flowing over the engine and not out the open holes! order all of the other sealing washers at the same time like the spark plugs and the oil pressure switch grommet. View/Change Diagram
$5.25
Make a selection 5910721 Right outer floorpan repair section. Galvanized primed painted. One of the most abused part of the 911 are the floor panels. Years of exposure to moisture, salt, sand, and mud often takes a toll on the metal under your feel. If your Porsche floors have seen better days and are showing the ugly signs of corrosion, we have replacement panels. Each one is painstakingly made to duplicate the factory pieces and galvanized for long life. General Fitment911 1965-69911 1987-89 911 1984-86 911 1978-83 930 1975-77 911 1974-77 911 1970-73
$352.35
Make a selection 591077 Left inner rocker panel. Galvanized primed painted. One of the most abused part of the 911 are the floor panels. Years of exposure to moisture, salt, sand, and mud often takes a toll on the metal under your feel. If your Porsche floors have seen better days and are showing the ugly signs of corrosion, we have replacement panels. Each one is painstakingly made to duplicate the factory pieces and galvanized for long life. General Fitment911 1965-69911 1987-89 911 1984-86 911 1978-83 930 1975-77 911 1974-77 911 1970-73
$130.14
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |