PORSCHE 356 B LED KITCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 911 1978-83 - Front Axle/Steering (includes uncategorized and accessory items) 21011123 Catalytic bypass pipe "x torque" design made by m&m in Germany. The x torque design in is a true x pipe design. It is open in the center to add backpressure for torque. Give's you 10-15 ft-lbs of torque in the mid range along with 10-15 hp in the higher rpms. Why settle for the traditional cross over cat design when you can add torque in the mid range where the 996's need it most! Dme programming is necessary. Without it you will get a check engine light (cel). Tech tip: for older cars repair-kit FVD mk 996300
From $764.50
Make a selection 220110981001 FVD Brombacherhas a long tradition of offering high quality, extensively tested, easily installed tuning products that offer proven performance. Those high standards naturally led us to the innovative pro design (ipd) plenum product. The ipd patented cast aluminum intake plenum with the larger 82 mm (gt3) throttle body (competition plenum) increases horsepower and torque by optimizing and increasing airflow into the intake manifold. But in order to capitalize on all the performance gains the ipd competition plenum can deliver, you must strike a balance with exhaust components and software. You cannot simply add the ipd competition plenum on the 981 series and expect large gains. But, no need to worry, the FVD ...(choose a part on the right to read more)
$1,479.50
Make a selection 21011125PSE Only for vehicles with Porsche standard sports exhaust system 200 cell, hjs tri-metal, hf (high flow) hjs catalytic cores with "u-torque" design, manufactured by m in Germany. The u-torque design compensates for the backpressure loss while running the high flow cats. The design minimizes the loss of low end torque and adds 10-15 ft-lbs of torque in the mid and top range of the rpms. Why settle for the traditional cross over cat design when you can add more torque in the mid-range and minimize the loss of torque down low where the 997's need it most! Please note: these fit the OEM mufflers and Porsche sport exhaust (pse) mufflers. Tech tip:add one of our installation kits FVD mk 997300
$3,311.00
Make a selection 21011196538 This sport muffler is engineered for the discerning Porsche 965 turbo owner who is interested in pure unbridled power and sound. It is hand made from t 321 grade stainless steel. All piping is mandrel bent for reduced backpressure and increased performance. The sport muffler exudes a lower, deeper linear-firing-order dominated flat 6 Porsche turbo sound with added turbo whistle. Exhaust tips are 76 mm (3 inch) polished ovals with a rolled lip. Each kit includes complete installation hardware, wastegate pipe and clamps. Features: gains of up to 10 hp more* t 321 stainless steel mandrel bent new wastegate pipe new gaskets new hardware new muffler clamps *dependent upon boost level and other modifications. Sold in...(choose a part on the right to read more)
$2,127.42
Make a selection 190111043G For use on obd1 (94 and earlier) cars only! Only 1 o2 bung is provided. Call for 1995 application. Will not work with multiple o2 sensor cars, like north american cars. (96-98) does not include a TUV-certificate. We recommend using our catalytic installation kit, part # FVDmk993300g please note: not legal for use on california pollution controlled motor vehicles.
$705.10
Make a selection 906634 Will ship when available. General Fitment911 1974-77930 1975-77 911 1978-83 911 1984-86 911 1987-89
$125.90
Make a selection 964347009BXATK This steering rack is a remanufactured part with a core, as such an additional charge (a core deposit) will be added to the purchase price of the part. After receiving your new part, kindly send back your old part, or core . Once the core is returned to us and it has been inspected to ensure it is rebuild-able and resell-able, the core deposit will be refunded. The remanufacturing process includes full inspection and testing for structural integrity. We then disassemble and bead blast to remove corrosion. Internals are micro-finished to OEM specifications. Sealing surfaces are carefully checked and restored prior to installing new premium seals and o-rings. Each unit is then carefully tested for full functional...(choose a part on the right to read more)
$1,633.50
Make a selection 96410090800EQ FVD cylinder head gasket sets contain high quality German sourced gaskets, seals and o-rings. This kit contains a complete set of gaskets to make a teardown / rebuild more convenient. Sold as a complete set. 1 necessary per car. To complete the gasket set for the whole engine order please 93010090104eq too.
$744.70
Make a selection 93035104803EQ The zimmermann OEM brake disc combines high-quality cast materials, a vented and perforated braking surface and includes z-coating. Features: better wet braking performance by permanent expulsion of brake dust and water. Sporty look. Anti corrosion "z-coating" prevents rust. Noticeable improvement in braking performance. Countersunk holes double as wear indicator. Simple bolt on, modifications are not necessary. Sold individually. 1 necessary per car. Rotors should always be changed in pairs; the front left is part # 93035104703eq please note: if you are looking for a kit with pads, etc. Please check our brake service kit selection.
$237.60
Make a selection 99310090236EQ FVD cylinder head gasket sets contain high quality German sourced gaskets, seals and o-rings. This kit contains a complete set of gaskets to make a teardown / rebuild more convenient. Sold as a complete set. 1 necessary per car. To complete the gasket set for the whole engine also order part # 93010090104eq
$614.58
Make a selection 93010590201EQ Attention: the 911 SC 3.0 liter only for vehicles without oil drain cover. This kit contains everything needed for a valve adjustment. High-quality victor reinz gaskets with hardware, designed to perform like the original. We source this kit in Germany to ensure quality, reliability and precise fitment. Set includes: 2 qty. Lower valve cover gaskets 93010519507 2 qty. Upper valve cover gaskets 93010519404 34 qty. Valve cover nuts 34 qty. Valve cover washers sold as a set. 1 necessary per car. Please note: please check the model fitment tab to ensure accurate fitment.
$52.80
Make a selection 99135294881 High-quality OEM (original equipment manufacturer) replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold as a rear set. 1 necessary per car. Please note: we also sell a complete kit with sensors, part # FVDbs352991005
From $355.75
Make a selection FVD10603500 Protect your engine and lower the operating water temperature by up to 60* f. Our kit contains everything you need to install this kit on a 3.4l 996. Don't be fooled by cheaper kits that claim they are complete, if the radiator is not supported correctly, road and track vibrations can destroy your investment. This fits Carrera c2 and c4 with manual transmission only ! This will not fit cars equipped with a tiptronic transmission.
$1,109.80
Make a selection FVD33150020 This kit is complete and includes the front and rear monoball cartridges with press tools. Our weather sealed monoball cartridges are crafted in high carbon steel and 7075 t6 aircraft aluminum. They will positively locate the suspension arms so suspension motion is accurately repeated in every corner. Sold as a set of 4. 1 kit is necessary per car. Please note: noise may resonate inside the cabin during street use.
$715.00
Make a selection FVD33150003 Rear toe control arms - order in pairs only restore proper suspension geometry with this adjustable lower rear control arm. The factory control arm can't compensate enough when lowering your Porsche, leaving you stuck with as much as ½ of toe in. The result is poor handling and rapid tire wear. This kit will provide the additional adjustment needed. The adjusting link has a left and right hand thread on each end. Rotating the link will increase or decrease the overall length of the arm. A precision teflon lined spherical rod end replaces the compliant rubber factory bushing for improved suspension response and feedback, and also reduces toe changes during acceleration and deceleration.
$218.90
Make a selection FVD33150030 This kit is complete and includes a total of 8, 4 smaller and 4 larger for the rear control arms. Our weather sealed monoball cartridges are crafted in high carbon steel and 7075 t6 aircraft aluminum. They will positively locate the suspension arms so suspension motion is accurately repeated in every corner. Sold as a set of 8. 1 kit is necessary per car. Please note: noise may resonate inside the cabin during street use.
$746.90
Make a selection 93010090803EQ High-quality victor reinz replacement gaskets, o-rings and washers to reseal your cylinder heads. Victor reinz has been supplying German auto manufacturers and Porsche for decades. They are a trusted name in gaskets and sealing products. This kit is complete with everything needed and we source this directly in Germany for an added level of quality. Sold individually. 1 set necessary per car. To complete the gasket set for the entire engine, also order part # 93010090104eq
$625.90
Make a selection FVD333007 These high quality, German made mounts are made specifically for rear shock absorbers that contain a 15mm i.d. Uniball spherical bearing. They are located at the base of the rear shocks, and secure the shock to the rear trailing arms. They are required with FVD exclusive suspension kits with part #'s 115 900 911 xx / xxx. For example 115900911030 they are also required for rear shocks like part # FVD33315755 sold as a set. 1 necessary per car.
$174.90
Make a selection FVD105911S This tensioner kit is an update for cars before 1984 and a replacement for cars after 1984. For the early non-cis cars (
$895.40
Make a selection 99660610599 If you are noticing engine vibrations, misfires and even backfiring your crankshaft position sensor maybe bad. Your car's dme (ecu) uses the signal from the crankshaft position sensor to control ignition timing and fuel injection, so if your sensor is failing your engine is suffering from poor timing and is not running efficiently. This kit is complete and ready to install.
$132.77
Make a selection 99650598600 This will also fit the 996 mk1 (98-01) with the factory cup aero kit. Please note: does not include installation hardware. Please order the installation hardware kit part # 99650598691mk
From $555.00
Make a selection 99311032701EQ Quality original style replacement filter. Are you adding this filter to a list for your next service? Please check out our engine maintenance kits, they contain everything needed to make your routine maintenance simple. Sold individually. 1 necessary per car.
$28.60
Make a selection 99312301352ATK Our k-16 remanufactured turbo is cost competitive and is a direct replacement. Simply send us your original k16 turbochargers and a borg warner / kkk certified technician will remanufacture your turbo. The remanufacturing process includes full inspection to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will replace the turbine wheels, thrust bearings, install new seals, install new waste gates, recondition the internals and high speed balance the turbo. This ensures reliability and superior performance for many years to come. The remanufacturing is done on an exchange basis only. You must send us your original k16 turboc...(choose a part on the right to read more)
$2,194.50
Make a selection BES99305040S FVD is proud to introduce our newest line of Brombacherexhaust systems. Brombacher exhausts are engineered for the discerning Porsche owner and offer unmatched performance, unparalleled quality, and incredible value. All of our exhausts are manufactured in Germany and are tested comprehensively for flow rate and characteristics, thermal stress, resistance to cracking, and longevity. Brombacher mufflers outer shell dampens and eliminates unwanted frequencies and ensures no resonance or drone in the cabin. The end result is a strong, linear, firing-order dominated flat-6 Porsche sound. In addition, Brombacherexhausts systems are available for ultimate performance full titanium. Our titanium system's are nearly...(choose a part on the right to read more)
$1,820.50
Make a selection ER2071600 Elephant racing low-friction control arm mounts allow for free control arm movement, eliminating any potential for binding. Elephant racing corrected a key factory design limitation:our mounts self-align in all axis, becoming collinear to avoid binding as the arm moves through its range of motion. The low-friction control arm mounts self-align in both the horizontal and vertical planes. The result is collinear front and rear mounts delivering smooth non-binding action. You get superior performance and a smoother ride. Kit includes everything required to upgrade one car. Factory rear mounts are replaced with our self-aligning mounts. Factory front mounts are retained and augmented with self-aligning washers. ...(choose a part on the right to read more) General Fitment911 1965-69911 1987-89 911 1984-86 911 1978-83 930 1975-77 911 1974-77 911 1970-73 914 1970-76 912 1965-69
$225.00
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |