PORSCHE 993 AC CONTROLSCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 911 1978-83 - Fuel/Exhaust (includes uncategorized and accessory items) FVD211622 This silicone hose supplies hot air to the heater control box, it replaces original part # 930 211 622 01. It runs from the exhaust heat exchanger to the heater control box. We recommend replacing the heater box clamp, part # 90121105122 on one end and a hose clamp part # 99951234902 on the other end. Sold individually. 2 necessary per car.
$52.80
Make a selection FVD33104381 The tow link is the furthest rear control arm on the rear axle. It is responsible for the toe angle adjustment. The OEM control arm bushings are simply too soft for track events and the teflon monoball racing bushings are too far too hard and noisy for street cars. Our sport bushings are made of a denser rubber (85 shore opposed to OEM 65 shore), which means that they are suitable for street and track use. Equally as important is that they do not produce any noise like the teflon bushings. FVD sport control arm facts: - better handling and more responsive. - makes precision adjustments of the suspension easier. - does not produce noise. - shore a hardness value of 85 for durability and handling. - fit's like o...(choose a part on the right to read more)
$451.96
Make a selection FVD33150003 Rear toe control arms - order in pairs only restore proper suspension geometry with this adjustable lower rear control arm. The factory control arm can't compensate enough when lowering your Porsche, leaving you stuck with as much as ½ of toe in. The result is poor handling and rapid tire wear. This kit will provide the additional adjustment needed. The adjusting link has a left and right hand thread on each end. Rotating the link will increase or decrease the overall length of the arm. A precision teflon lined spherical rod end replaces the compliant rubber factory bushing for improved suspension response and feedback, and also reduces toe changes during acceleration and deceleration.
$218.90
Make a selection FVD34101702RAK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will properly install our FVD race front control arm bushings. They are made with uniball bearings so suspension motion is accurately repeated in every corner. Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrange...(choose a part on the right to read more)
$438.90
Make a selection FVD3419991 This is a cost effective alternative to buying new control arms. Replace worn-out original soft rubber (65 shore hardness value) control arm bushings with new bushings of the same rubber (65 shore hardness value). This bushing set is made in Germany, weather sealed, crafted in high carbon steel and 7075 t6 aircraft aluminum and includes a 65 shore hardness value cores. This is a front and rear bushing for the front lower control arm (wishbone). 2 sets are necessary per car.
$124.30
Make a selection 96457278500EQ This part is sourced in Germany to ensure quality, reliability and precise fitment. Sold individually. 2 necessary per car.
$79.20
Make a selection FVD34101802RAK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will properly install our FVD race front control arm bushings. They are made with uniball bearings so suspension motion is accurately repeated in every corner. Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrange...(choose a part on the right to read more)
$438.90
Make a selection FVD34105304BU1 Diese buchse ersetzt an ihrem vorderen querlenker die mittlere buchse. Es handelt sich bei dieser buchse um einen hartegrad von 85 shore wie original bei den rs -modellen ( GT3 rs, GT2 rs ) preis pro stuck, pro querlenker wird ein stuck benotigt.
$115.50
Make a selection
$46.20
Make a selection FVD99161801
$1,931.61
Make a selection FVD34391101SET Replace worn-out original front lower control arm bushings to return your car to its intended suspension geometry and steering feedback. Features: better handling reduces that sloppy steering feel does not produce any noise like the teflon bushings. Rubber has the original shore hardness value of 65 (like oem) fit's like oem, simple installation made in Germany if you are looking for a sportier upgrade we suggest our sport lower control arm set, part # FVD34391192set. Set is sold per axle. 2 necessary per car.
$152.90
Make a selection
$315.87
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |