PORSCHE 996 REAR ENDCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 911 1978-83 - Transmission (includes uncategorized and accessory items) AP958170 Agency power is proud to release its super sport exhaust system for the 958 Porsche Cayenne s v8 2011 and up. the super sport exhaust is a axle system that gives your 4.8l v8 engine a real aggressive tone. made here in the usa, the exhaust saves close to 30lbs off the rear end of the vehicle. using 304 stainless steel and detail oriented tig welding, the exhaust system uses two small high flow mufflers which give it the sports car rumble. its reduced back pressure design gives the engine improved horsepower and torque with most noticeable improvement in throttle response. because of the reduced restriction, this exhaust horsepower gains can definitely be noticed in the mid to top rpm range.
$1,495.95
Make a selection 96410601402EQ This OEM cover sits low nearest the rear bumper. If you are removing the motor for maintenance, be sure to check and replace the engine covers / heat shields as necessary. We recommend purchasing a new seal, part # 96410622301 and plug, part # 96410623701 to complete the installation. Sold individually. 1 necessary per car.
$601.70
Make a selection BBI9964010003 Features
$550.00
Make a selection FVD512997GT3RST 997 GT3 rear spoiler fits 997turbo includes: deck lid, aluminum upright, 3rd brake light housing and kevlar/carbone wing (l= 145cm, b=28cm, h=7 cm) with end plates. Material: aluminum, fiberglass, kevlar-carbone. Also available with wing blade in fiber (gfk) FVD512997gt3rs tech tip: facelift models (2009- ), the 3rd brake light can usually be assumed. If necessary please order the 3rd brake light 99763105201 separately. The holes for the intake fan on the rear deck lid must be drilled prior to installation (model variations). Please note wing is fixed and is not adjustable. The air inlet of the rear is not included. Please order 99751262592g2x
$6,528.50
Make a selection FVD33300909ATK This non-adjustable rear spring plate is remanufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. New rs spec. (85 shore) rubber bushings are installed to make this a direct bolt on. 85 shore rubber is more durable than OEM 65 shore and provides more positive suspension location yet is still quiet and compliant for street use. Features: includes new rs spec. (85 shore) rubber bushings made in Germany sold individually. 2 necessary per car. This part is a remanufactured part. Send us your original and we will have it remanufactured for you. We do not offer a core exchange on this part. Each is remanufactured in Germany, so the lead times can vary.
$342.10
Make a selection FVD33150005 Restore proper suspension geometry with this adjustable lower rear control arm. The factory control arm cannot compensate enough when lowering your Porsche, leaving you with as much as ½ inch of toe in. The result is poor handling and rapid tire wear. This kit will provide the additional adjustment needed. The adjusting link has a left and right hand thread on each end. Rotating the link will increase or decrease the overall length of the arm. A precision teflon lined spherical rod end replaces the compliant rubber factory bushing for improved suspension response and feedback, and also reduces toe changes during acceleration and deceleration. Sold in pairs. 1 necessary per car.
$764.50
Make a selection WAP0407120A Fold-out stick in the same design as the Porsche sports car vehicle key. Porsche crest on the front. Led control light on the rear. The plug direction depends on the usb port being used. It can store up to 4 gb of data and is compatible with various operating systems including the Porsche communication management system with the individual universal audio interface option. In black with chrome. Dimensions: 53.5 x 38 x 19.5 mm General FitmentACCESSORY
$64.90
Make a selection FVD35161103B Wheel spacers make your tires and wheels appear wider by moving the wheel out from the hub, providing both performance and appearance improvements. Whether you want improved handling, increased safety, or simply desire your car to make a statement about your individual style, wheel spacers can help you accomplish your goal. This spacer fits between the wheel and hub. Size: 7 mm (.275 inches) bolt pattern: 5/130 center bore: 71.6 bolt / stud: n/a thread type: 14x1.5 material: strength tested aluminum alloy coating: anodized for corrosion protection hub alignment set screws are included. Longer bolts sold separately depending on application. Made in Germany. Sold individually. Can be used in front and/or rear. No...(choose a part on the right to read more)
$40.70
Make a selection RES96400100S1 More low and mid-range torque than our race system with cat bypass. Larger primaries, larger collector, largest diameter tubing on the market. Made for mid-range and top end performance with the added beauty of dual exhaust tips! + 25 hp & + 23 torque - 100 cell hjs tri-metallic race catalytics. -2 1/2 tubing (63.5mm) for max. Power across the rpm range.* -weighs 49 lbs. (22 kg). -German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - aeroquip cone style catalytic connection design to prevent exhaust leaks. -includes aeroquip quick release clamps. -made in Germany by m&m exhaust, gmbh. -dual round 3 exhaust tips -intoxicating flat 6 growl at idle, partial throttle and wide open throttle. P...(choose a part on the right to read more)
$7,403.00
Make a selection FVD51299102MM The moshammer vented rear diffuser with fins is an aggressive design that reduces aerodynamic drag. This vented diffuser allows air that is trapped by the rear bumper to exit, allowing for greater top end performance. The design also incorporates 5 fins that improve laminar airflow by reducing turbulence. Moshammer manufactured this as a direct replacement, so it secures seamlessly to the factory locations with the original hardware. This is an ideal addition for a leased vehicle or for those looking to return the car to its original appearance in the future. When added to other elements of the downforce rs (991.1 turbo/s) package, the result is a confident, cohesive stance with balanced downforce. Features: ve...(choose a part on the right to read more)
$1,460.80
Make a selection CCPOLYC Our custom-fit car covers fit your Porsche like a glove! Car covers are an excellent and inexpensive way to preserve your Porsche. Durable, woven poly cotton blend offers good basic vehicle protection. Polyester is sun and water resistant, while cotton give a soft touch to the vehicle’s finish. When ordering, please indicate your year, make, model, number of side mirrors, regular or turbo or turbo-look body style, with or without whale tail spoiler, and which type cover you would like. These covers are made to order and will take longer to ship. General FitmentALL
$249.00
Make a selection CB43207B Corbeau 3-point, 2" harness belts are an affordable way to upgrade your vehicle to harness belts. With a 3-point harness belt, the two shoulder straps go over your shoulders and through the harness slots in your seats. After they go through the harness slots these straps come together to form a y and you then mount the one remaining strap in the rear area of your vehicle. General FitmentALL
$119.00
Make a selection FVD33300902AT Send us your original spring plate and we will have it reconditioned for you. The reconditioning process includes full inspection to ensure proper operation after the remanufacturing process. We then disassemble, degrease and media blast the part. Once fully prepared, we install new rs spec. (85 shore) rubber bushings/bearings. 85 shore rubber is more durable than OEM 65 shore and provides more positive suspension location yet is still quiet and compliant for street use. Then we seal the spring plate with a corrosion resistant plating. Sold individually. 2 necessary per car. Please note: this only fits cars with the g50 transmission.
$261.80
Make a selection FVD33300905ATK Send us your original spring plate and we will have it reconditioned for you. The reconditioning process includes full inspection to ensure proper operation after the remanufacturing process. We then disassemble, degrease and media blast the part. Once fully prepared, we install new rs spec. (85 shore) rubber bushings/bearings. 85 shore rubber is more durable than OEM 65 shore and provides more positive suspension location yet is still quiet and compliant for street use. Then we seal the spring plate with a corrosion resistant plating. Sold individually. 2 necessary per car. Please note: this does not fit cars with the g50 transmission.
$312.40
Make a selection FVD34391101SET Replace worn-out original front lower control arm bushings to return your car to its intended suspension geometry and steering feedback. Features: better handling reduces that sloppy steering feel does not produce any noise like the teflon bushings. Rubber has the original shore hardness value of 65 (like oem) fit's like oem, simple installation made in Germany if you are looking for a sportier upgrade we suggest our sport lower control arm set, part # FVD34391192set. Set is sold per axle. 2 necessary per car.
$152.90
Make a selection BEC993001GSOH Brombacher exclusive covers are completely manufactured in the south of Germany in baden wurtemberg, between stuttgart and our local mountains in the southern black forest. The materials chosen is environmentally friendly production and each stich is made with care. 100% Germany quality, perfect, personalized appearance for every taste, even in the covered state a mixture of cotton and polyester nano-coated on the outside which makes it so dirt and water repellent, completely paint-friendly, with very breathable construction. Price includes: cover color selection, color selection of trim, custom embroidered logo and a matching bag with a small custom logo, in the same colors. Please let us know what model, year...(choose a part on the right to read more)
$873.40
Make a selection BEC996001SO Brombacher exclusive covers are completely manufactured in the south of Germany in baden wurtemberg, between stuttgart and our local mountains in the southern black forest. The materials chosen is environmentally friendly production and each stich is made with care. 100% Germany quality, perfect, personalized appearance for every taste, even in the covered state a mixture of cotton and polyester nano-coated on the outside which makes it so dirt and water repellent, completely paint-friendly, with very breathable construction. Price includes: cover color selection, color selection of trim, custom embroidered logo and a matching bag with a small custom logo, in the same colors. Please let us know what model, year...(choose a part on the right to read more)
$873.40
Make a selection BEC911964GST Brombacher exclusive covers are completely manufactured in the south of Germany in baden wurtemberg, between stuttgart and our local mountains in the southern black forest. The materials chosen is environmentally friendly production and each stich is made with care. 100% Germany quality, perfect, personalized appearance for every taste, even in the covered state a mixture of cotton and polyester nano-coated on the outside which makes it so dirt and water repellent, completely paint-friendly, with very breathable construction. Price includes: cover color selection, color selection of trim, custom embroidered logo and a matching bag with a small custom logo, in the same colors. Please let us know what model, year...(choose a part on the right to read more)
$873.40
Make a selection FVD33150010 Our weather sealed monoball cartridges are crafted in high carbon steel and 7075 t6 aircraft aluminum. They will positively locate the suspension arms so suspension motion is accurately repeated in every corner. Sold as a set. 1 kit is necessary per car. Please note: we recommend this kit for race use, as noise may resonate inside the cabin during street use. For those that are concerned about the noise, please order part # FVD3310212291
$704.00
Make a selection BEC9972GT3RS Brombacher exclusive covers are completely manufactured in the south of Germany in baden wurtemberg, between stuttgart and our local mountains in the southern black forest. The materials chosen is environmentally friendly production and each stich is made with care. 100% Germany quality, perfect, personalized appearance for every taste, even in the covered state a mixture of cotton and polyester nano-coated on the outside which makes it so dirt and water repellent, completely paint-friendly, with very breathable construction. Price includes: cover color selection, color selection of trim, custom embroidered logo and a matching bag with a small custom logo, in the same colors. Please let us know what model, year...(choose a part on the right to read more)
$836.00
Make a selection FVD512991GT3RS Made in Germany by a premier manufacturer of motorsport body work. Extremely high-quality, aero-tested, paintable grp (glass reinforced plastic) deck lid with functional GT3 wing. The decklid has functional, yet subtle ram air spoiler incorporated into the design like the GT3. The ram air spoiler increases the velocity of the air into the intake for added performance. This decklid is also available with a polished carbon wing, part # FVD 512 991 GT3 rsc features: produced by a premier German motorsports manufacturer. Motorsport quality standards. Lightweight. Decklid made of high strength, lightweight grp (glass reinforced plastic). Mounts like factory. Includes: grp deck lid grp wing grp end plates aluminum up...(choose a part on the right to read more)
$5,362.50
Make a selection 240991352RSL1 Pagid yellow rsl1 are from the rsl line of endurance racing brake pads. They are a high friction coefficient racing compound with long pad and disc life, and are easily bedded in. Rsl1 pads are manufactured of a low metallic resin bonded material containing steel and acrylic fibers. They operate in a wide operating temperature range and have good friction stability vs. Temperature. Applications include: GT cars, touring cars, prototype racing and in spring racing. Features at a glance: high friction coefficient high bite high fade resistance high pad and disc life high modulation pagid is one of the leading manufacturers of racing brake pads and is successful at the world's most demanding racetracks. They offe...(choose a part on the right to read more)
$743.60
Make a selection 93050503200EQ Don't let a worn, faded, wax covered bumper guard detract from your cars exterior. This is a high-quality OEM replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. We recommend adding a new license plate light, part # 91163162004 to complete the update. Sold individually. 1 necessary per car.
$179.30
Make a selection FVD545911001 - grun getont fur fahrzeuge ohne zierrahmen - ohne loch fur heckwischer - ohne heizung (keine storenden heizdrahte) - original dichtung verwendbar - ca. 10% leichter als das original (gewicht ca. 6,0 kg)
$892.01
Make a selection 240996352RSL1 Pagid yellow rsl1 are from the rsl line of endurance racing brake pads. They are a high friction coefficient racing compound with long pad and disc life, and are easily bedded in. Rsl1 pads are manufactured of a low metallic resin bonded material containing steel and acrylic fibers. They operate in a wide operating temperature range and have good friction stability vs. Temperature. Applications include: GT cars, touring cars, prototype racing and in spring racing. Features at a glance: high friction coefficient high bite high fade resistance high pad and disc life high modulation pagid is one of the leading manufacturers of racing brake pads and is successful at the world's most demanding racetracks. They offe...(choose a part on the right to read more)
$512.60
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |