Vehicles
Sections
473 not categorized PORSCHE 944 CV AXLCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 911 1978-83 (includes uncategorized and accessory items) FVD33396410 A cost effective FVD exclusive combination of bilstein clubsport shocks with a set of eibach pro kit springs. This suspension kit is meant for those who want the car to sit at the lowest possible ride height. This set up will allow you to lower the front axle by 2.4 inches (60 mm). This is a perfect kit for clubsport or race use where the surfaces are smooth and even. The stock rs ride height was 1.6 inches (40 mm) lower. So, this is a full 3/4 of an inch (20 mm) lower on the front axle. Sold as a complete kit. 1 kit is necessary per car. Please note: we recommend the b6 / ohlins suspension kits for those looking for more comfort for street use.
$2,726.50
Make a selection BK7033 Re-issue of autobooks manual covering engine, fuel & cooling systems, ignition, heating, exhaust emissions, clutch, transmission, rear axle, suspension, steering gear, brakes, electronics, and bodywork. This is a manual that will help keep 912 on the road. A must for any 912 owner. General FitmentACCESSORY
$32.00
Make a selection FVD33391100SET Replace worn-out original spring plate bushings to return your car to its intended ride quality and performance. This is a high-quality OEM 65 shore density bushing set, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. This set is a direct replacement for original part # 911 333 009 00 sold as a set. 1 necessary per axle.
$108.90
Make a selection 93033203400 If you are experiencing clicking noises when cornering, shaking, vibration and you see grease on the inside edge of the tire, then odds are your drive shafts cv joints are failing. This is a high-quality OEM (original equipment manufacturer) replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Repair kit includes: 1 qty. Cv (constant velocity) joint 2 qty. Genuine gkn grease packets 1 qty. Cv joint spring 1 qty. Cv boot clamp 1 qty. Cv boot 1 qty. Gasket 1 qty. Cv joint snap ring sold individually. 4 necessary per car (2 per axle). Please note: this only fits 930 turbo models with the 4 speed transmission # 930.34/36 and the 1984 ...(choose a part on the right to read more) View/Change Diagram
From $104.33
Make a selection 24135299702YS High efficiency performance and race brake pads for track & street use. These are a high friction pad that are very resistant to heat and are fast to bed-in. Yellowstuff has been used with great success in both race and street cars. Yellowstuff is an aramid fiber-based brake compound with high brake effect even when cold. Yellowstuff is possibly one of the first ever compounds that can be used for street or track driving. These pads do not require warm up but do get even stronger under the heat of hard driving. These are not a low dust pad and if your desire is for a low dust premium street use pad, you should consider ebc redstuff. Features: made for up to 900*c (1,650*f). Developed for race cars but are stree...(choose a part on the right to read more)
$284.90
Make a selection BBI9964010004 Features
$795.00
Make a selection 99160918500 When your pads reach a critical level, these sensors will trigger a warning to alert you that your pads need to be changed. Be sure to purchase these in conjunction with your new brake pads. High-quality OEM replacement designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 2 necessary per axle. Please note: please check the model fitment tab to ensure accurate fitment.
From $24.84
Make a selection FVD33104381 The tow link is the furthest rear control arm on the rear axle. It is responsible for the toe angle adjustment. The OEM control arm bushings are simply too soft for track events and the teflon monoball racing bushings are too far too hard and noisy for street cars. Our sport bushings are made of a denser rubber (85 shore opposed to OEM 65 shore), which means that they are suitable for street and track use. Equally as important is that they do not produce any noise like the teflon bushings. FVD sport control arm facts: - better handling and more responsive. - makes precision adjustments of the suspension easier. - does not produce noise. - shore a hardness value of 85 for durability and handling. - fit's like o...(choose a part on the right to read more)
$451.96
Make a selection 11595B00HR Lowering up 40mm, front axle load 1290kg / 1340kg rear
$614.90
Make a selection FVD33399300 A cost effective FVD exclusive combination of bilstein clubsport shocks with a set of TUV certified eibach springs. This suspension kit will lower the front axle to a maximum of 35 mm (1.37 inches) and the rear axle to 30 mm (1.18 inches), like the European rennsport model. The height is adjustable as the dampers are threaded. They are a cost effective solution for clubsport use and will be well mannered on the street. Sold as a complete kit. 1 kit is necessary per car.
$11,872.30
Make a selection 24135299702RS Tired of having to wash the car just due to brake dust build up? Ebc redstuff brake pads have you covered. They reduce brake dust by 60-90%, plus the minimal dust is safely removed with a wet sponge as redstuff does not contain steel fiber particles found in other pads. These pads also have excellent brake friction when cold and just get better as they warm up. The pads are composed of a kevlar fiber-based brake compound enhanced with ceramic particles. The benefits of this material are longevity, enhanced braking performance, quiet operation and reduced brake dust. Features: made for up to 750*c (1,382*f) for street, track and rally use. Low dust, high performance street pad with 20-25% braking improvement. Ca...(choose a part on the right to read more)
$261.80
Make a selection FVD33105900 Replace worn-out rear trailing arm bushings with our FVD sport bushings, made of rubber with an 85 shore hardness value that is the same as the rs models. 85 shore is more durable, provides more positive suspension location and is still quiet and comfortable for street use. This is a direct replacement for original part # 90133105900 features: better handling makes precision adjustments of the suspension easier does not produce any noise like the teflon bushings. Rubber has a shore hardness value of 85 (like rs models) fit's like oem, simple installation made in Germany set is sold per axle. 1 necessary per car.
$154.00
Make a selection 115900944020CS Double spring suspension (racing) for 924 only for 20mm spring strut mounting this sport suspension was tuned and tested for racing use only (hockenheimring.net). Perfect handling, recommended for race and clubsport. Not for street use (racing suspension). The lowering is adjustable (30-70mm front and 30-60mm rear). By using springs at the rear axle instead of torsion bars you improve extreme the handling of your car. By removing the rear torsion bars is the weight saving approximately 25kg.
$2,633.40
Make a selection 150TB2129 High-performance, direct replacement torsion bar set that allow you to dial in the correct spring rate for street or track use. Features: manufactured from aircraft grade, 4340 alloy steel heat treated for increased strength and durability powder coated to resist corrosion consistent outside diameter and rate for consistent spring rate made in the usa by sway-a-way sold as a set. 1 necessary per axle.
$603.90
Make a selection 240981351GV Pagid yellow rsl29 are from the rsl line of endurance racing brake pads. They are a medium friction coefficient racing compound with long pad and disc life, and are easily bedded in. Rsl29 pads are manufactured of a low metallic resin bonded material containing steel and acrylic fibers. They operate in a wide operating temperature range and offer excellent release characteristics. Rsl29 pads offer low heat conductivity and work well with abs systems. They offer excellent modulation and controllability. They offer lower disc wear rates and are fade resistant up to a temperature of 650*c (1,202*f). Applications include: club racing, track days, touring cars, prototype endurance racing and GT cars. Features at a g...(choose a part on the right to read more)
$632.50
Make a selection 150TB112801 High-performance, direct replacement torsion bar set that allow you to dial in the correct spring rate for street or track use. Features: lighter weight tubular / hollow torsion bar set manufactured from aircraft grade, 4340 alloy steel heat treated for increased strength and durability powder coated to resist corrosion consistent outside diameter and rate for consistent spring rate made in the usa by sway-a-way sold as a set. 1 necessary per axle.
$515.90
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |