PORSCHE CAYMAN S EFLCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 911 1984-86 - Brakes/Wheels (includes uncategorized and accessory items) WAP093001 Sized to fit all current 2001 Porsche calendars. Aluminum frame with anti-reflective glass.
$49.61
Make a selection FVD33150005 Restore proper suspension geometry with this adjustable lower rear control arm. The factory control arm cannot compensate enough when lowering your Porsche, leaving you with as much as ½ inch of toe in. The result is poor handling and rapid tire wear. This kit will provide the additional adjustment needed. The adjusting link has a left and right hand thread on each end. Rotating the link will increase or decrease the overall length of the arm. A precision teflon lined spherical rod end replaces the compliant rubber factory bushing for improved suspension response and feedback, and also reduces toe changes during acceleration and deceleration. Sold in pairs. 1 necessary per car.
$764.50
Make a selection FVD34391192SET Replace worn-out original front lower control arm bushings with our FVD sport bushings, made of rubber with an 85 shore hardness value that is the same as the rs models. 85 shore is more durable, provides more positive suspension location and is still quiet and comfortable for street use. Features: better handling reduces that sloppy steering feel makes precision adjustments of the suspension easier does not produce any noise like the teflon bushings. Rubber has a shore hardness value of 85 (like rs models) fit's like oem, simple installation made in Germany set is sold per axle. 2 necessary per car.
$158.40
Make a selection FVD33105900 Replace worn-out rear trailing arm bushings with our FVD sport bushings, made of rubber with an 85 shore hardness value that is the same as the rs models. 85 shore is more durable, provides more positive suspension location and is still quiet and comfortable for street use. This is a direct replacement for original part # 90133105900 features: better handling makes precision adjustments of the suspension easier does not produce any noise like the teflon bushings. Rubber has a shore hardness value of 85 (like rs models) fit's like oem, simple installation made in Germany set is sold per axle. 1 necessary per car.
$154.00
Make a selection 95037003 Stoptech brake lines consist of a ptfe (commonly referred to as teflon) inner line that carries the brake fluid, which is then covered with a layer of stainless steel woven braid. The ptfe tube is very resistant to expansion under pressure and will not degrade from exposure to brake fluid. every stoptech brake line is 100% tested in-house to a pressure of 4,500 psi. This is almost 4 times the typical line pressure exerted by a production vehicle's master cylinder. stoptech is a registered brake line manufacturer with the united states DOT and all stoptech stainless steel brake lines are manufactured to meet DOT compliance standards. Stoptech stainless steel lines also meet or exceed fmvss 106 and applicable...(choose a part on the right to read more) General Fitment911 1965-69911 1970-73 911 1974-77 911 1978-83 911 1984-86 912 1965-69
$91.60
Make a selection FVD6314051 Now we can offer you OEM quality clear turn signals. We have sourced these from Bosch in Germany directly. Bosch is a worldwide leading developer and manufacturer of automotive technology. They represent maximum quality and reliability and go above and beyond any minimum legal specifications. These turn signals are e-1 certified in Germany. They will not fade and discolor with time like those on the market in the past. The set includes 2, 12v 21 watt amber bulbs to meet road regulations. If you would like a clear set of bulbs that flash amber, order part # FVD631752 sold as a set. 1 necessary per car. Please note: these are euro spec turn signals so the flat reflectors hole for the bulb holder is not cutout. Eu...(choose a part on the right to read more)
$324.50
Make a selection FVD33104381 The tow link is the furthest rear control arm on the rear axle. It is responsible for the toe angle adjustment. The OEM control arm bushings are simply too soft for track events and the teflon monoball racing bushings are too far too hard and noisy for street cars. Our sport bushings are made of a denser rubber (85 shore opposed to OEM 65 shore), which means that they are suitable for street and track use. Equally as important is that they do not produce any noise like the teflon bushings. FVD sport control arm facts: - better handling and more responsive. - makes precision adjustments of the suspension easier. - does not produce noise. - shore a hardness value of 85 for durability and handling. - fit's like o...(choose a part on the right to read more)
$451.96
Make a selection FVD37504332R Replace the worn-out, original soft rubber engine mounts with our higher density, rs specification rubber bushings. These are manufactured of rubber with an 85-shore hardness value. 85-shore is the same density as what is used in the rs models. It is more durable, provides more positive, sharper shifts and offers crisper throttle response. Yet, rs spec rubber is still quiet and comfortable for street use. Features: sharper shifts crisper throttle response does not produce nvh (noise vibration harshness) like teflon or solid bushings. Rubber has a shore hardness value of 85 (like rs models) made in Germany sold as a set. 1 necessary per car.
$152.90
Make a selection BL911A Over the years, deposits form inside your rubber brake lines, creating a hard brake pedal and sticky calipers. The permanent cure is to install a set of our stainless brake lines. They are teflon-lined to prevent mineral build-up and braided stainless steel to reduce line flex! (sold in sets of four.) excellent brake hose for racing. General Fitment911 1974-77930 1975-77 911 1978-83 911 1984-86 911 1987-89
$75.59
Make a selection 150PB100922 Replace worn-out original sway bar bushings with this longer lasting poly-graphite plastic bushing. Poly-graphite is higher density than OEM rubber, so suspension components will experience less deflection. It is specially formulated with a graphite lubricant to produce a bearing like action. We also recommend replacing the sway bar to ball pin bushing at the same time to save on labor costs, part # 90134378200 sold individually. 4 necessary per car. Please note: this fit's genuine rear sway bars only.
$44.00
Make a selection 150SPB965 Replace the worn-out spring plate bushing with this longer lasting poly-graphite plastic bushing. Poly-graphite is higher density than OEM rubber so suspension components will experience less deflection. It is specially formulated with a graphite lubricant to produce a bearing like action. This is the inner bushing for the 1-piece non-adjustable spring plate. Sold individually. 2 necessary per car.
$47.30
Make a selection 150TBF900 Replace worn-out original front control arm / wishbone bushings with this longer lasting poly-graphite plastic bushing. Poly-graphite is higher density than OEM rubber so suspension components will experience less deflection. It is specially formulated with a graphite lubricant to produce a bearing like action. This is located at the front of the control arm / wishbone. The correct matching poly-graphite bushing for the rear of the control arm is part # 150tbr900 sold individually. 2 necessary per car.
$48.40
Make a selection 96437504381 Replace your worn-out, original soft rubber engine mounts with our higher density, rs specification rubber bushing. This is manufactured of rubber with a 75-shore hardness value. 75-shore is the same density as what is used in the rs models. It is more durable, provides more positive, sharper shifts and offers crisper throttle response. Yet, rs spec rubber is still quiet and comfortable for street use. Features: sharper shifts crisper throttle response does not produce nvh (noise vibration harshness) like teflon or solid bushings rubber has a shore hardness value of 75 (like rs models) made in Germany this mount is a high-quality OEM (original equipment manufacturer) replacement part, designed to perform like t...(choose a part on the right to read more)
From $199.99
Make a selection 150PB10134 Replace worn-out original sway bar drop link bushings with this longer lasting poly-graphite plastic bushing set. Poly-graphite is higher density than OEM rubber so suspension components will experience less deflection. It is specially formulated with a graphite lubricant to produce a bearing like action. The set includes 4 complete bushings and 4 sleeves (8mm inner diameter). Sold as a set. 1 necessary per car.
$73.70
Make a selection 911FDLNK Upgrade your stock front swaybar with this simple bolt in replacement for the factory drop links.
$205.00
Make a selection 150PB100916 Replace worn-out original sway bar bushings with this longer lasting poly-graphite plastic bushing. Poly-graphite is higher density than OEM rubber, so suspension components will experience less deflection. It is specially formulated with a graphite lubricant to produce a bearing like action. We also recommend replacing the sway bar to ball pin bushing at the same time to save on labor costs, part # 90134378200 sold individually. 4 necessary per car. Please note: this fit's genuine rear sway bars only.
$44.00
Make a selection 150PB00619 Replace worn-out original stabilizer bar bushings with this longer lasting poly-graphite plastic bushing. Poly-graphite is higher density than OEM rubber so suspension components will experience less deflection. It is specially formulated with a graphite lubricant to produce a bearing like action. Sold individually. 2 necessary per car. Please note: this fits 911 models from 1965-73 if fitted with 19 mm original stabilizer bars. It also fits the 1975-77 930 turbo model if fitted with 19 mm original stabilizer bars.
$57.20
Make a selection 150SC030 Protect your valuable dashboard and interior the next time you take your car out! Our sun shades are tailor fitted for your Porsche! Features: laminate construction for durability. Silver reflective surface. Foam core for insulation. Folds easily for storage.
$109.99
Make a selection 802027 Hella is one of the top names in automotive lighting and electrical systems, since 1899. Hella produces lighting systems for many European OEM applications, as well as aftermarket performance lighting systems. Each of their light kits feature high-performance bulbs, quality-made lamp housings and mounts, precision-engineered reflectors and optics, and detailed installation instructions. The 550 high-performance driving lamp is made of high-impact abs plastic. It can be mounted upright or pendant. Each 550 kit contains (2) halogen lamps, (2) 12v 55 watt halogen bulbs, (1) prewired color-coded wire harness with 12v fused relay and illuminated rocker switch and (2) stone shields. Pre-fitted cables make installatio...(choose a part on the right to read more) General FitmentALL
$178.41
Make a selection 802026 Hella is one of the top names in automotive lighting and electrical systems, since 1899. Hella produces lighting systems for many European OEM applications, as well as aftermarket performance lighting systems. Each of their light kits feature high-performance bulbs, quality-made lamp housings and mounts, precision-engineered reflectors and optics, and detailed installation instructions. The 550 high-performance fog lamp is made of high-impact abs plastic. It can be mounted upright or pendant. Each 550 kit contains (2) halogen lamps, (2) 12v 55 watt halogen bulbs, (1) prewired color-coded wire harness with 12v fused relay and illuminated rocker switch and (2) stone shields. Pre-fitted cables make installation ea...(choose a part on the right to read more) General FitmentALL
$135.00
Make a selection 91156400501 Known as: air deflector / air deflector without / air deflector with spoiler f 91ks1 20767>>
$157.78
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |