PORSCHE 964 EMSCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 911 1984-86 - Fuel/Exhaust (includes uncategorized and accessory items) FVD3419991 This is a cost effective alternative to buying new control arms. Replace worn-out original soft rubber (65 shore hardness value) control arm bushings with new bushings of the same rubber (65 shore hardness value). This bushing set is made in Germany, weather sealed, crafted in high carbon steel and 7075 t6 aircraft aluminum and includes a 65 shore hardness value cores. This is a front and rear bushing for the front lower control arm (wishbone). 2 sets are necessary per car.
$124.30
Make a selection FVD375003 Are you experiencing vibrations in the cabin? The most likely cause is a worn transmission mount. Severely worn mounts translate to engine component wear and can even cause difficulty shifting. Our mount is manufactured in europe by an OEM supplier using the finest materials. It is a 65 shore rubber hardness value which is the same as the what was standard on these cars. Be sure to swap yours out during your next service. Sold individually. Central fitment in transmission carrier 96437502301. 1 qty. Required. Tech tip: now is the time to replace the old hardware as well. Below is a list of what is needed for installation. 1 qty. Hex head bolt m10x100 90007429202 1 qty. Lock nut m10 49020001 2 qty. Washers 10.3x...(choose a part on the right to read more)
$165.00
Make a selection FVD641102105SOBR01 Check-engine light position top right. Like new
$63.80
Make a selection G64641102104
$73.70
Make a selection G64641102103SIR01 Like new
$25.30
Make a selection 22011090102ATK Sport throttle bodies are a great addition for those with highly modified cars. They are a great addition for those with full exhaust systems (larger diameters), maf kits, larger displacements, street or race cams, etc. The remanufacturing process includes full inspection of your throttle body to ensure proper operation after the remanufacturing process. We then disassemble and bore the original to a 2.7-inch (70.5 mm) diameter. The entire throttle body is cleaned, degreased and the internals are polished to create more laminar flow. We then machine the shaft to accept larger butterfly's which seamlessly match the bore. All clearances are checked for precision to ensure reliability. Each throttle body is reman...(choose a part on the right to read more)
$589.60
Make a selection RES96400100S1 More low and mid-range torque than our race system with cat bypass. Larger primaries, larger collector, largest diameter tubing on the market. Made for mid-range and top end performance with the added beauty of dual exhaust tips! + 25 hp & + 23 torque - 100 cell hjs tri-metallic race catalytics. -2 1/2 tubing (63.5mm) for max. Power across the rpm range.* -weighs 49 lbs. (22 kg). -German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - aeroquip cone style catalytic connection design to prevent exhaust leaks. -includes aeroquip quick release clamps. -made in Germany by m&m exhaust, gmbh. -dual round 3 exhaust tips -intoxicating flat 6 growl at idle, partial throttle and wide open throttle. P...(choose a part on the right to read more)
$7,772.60
Make a selection FVD641102105SUNR01 Check-engine light down left. Like new
$63.80
Make a selection 21011196402 Say good bye to the days of having to weld and cut aftermarket sport cats to make them fit! We have our sport cats made in Germany to our specifications and that means that these are 100% bolt on without issue! - + 10 crank hp & +6 crank torque. - 200 cell, tri metallic German hjs sport catalysts. - large volume o 105 mm (4.1 inch diameter) high flow cat. - exhaust hanger brackets are included so that the heat shield does not have to be removed. - weighs 7.2 lbs. (3,2 kg). - direct bolt on replacement. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - reduces backpressure and thermal stress. - made in Germany. - more distinguished flat 6 growl at wide open throttle. The FVD 200 cell...(choose a part on the right to read more)
$1,593.90
Make a selection 911051 Porsche 911 ac compressor upgrade kit, 1984-89, lh drive model provides improved integrity with our kuehl barrier hose set, kuehl low- high pressure switch to help protect the system, a new denso factory compressor with clutch, new kuehl drier, complete o-ring kit, along with r134a charge port adapters. you can use either r12 or r134a with refrigerant with this complete kit. all barrier hoses match OEM configuration, have sae sae approved crimped fittings and each hose is labeled so you know where it goes.
$1,097.00
Make a selection 96410524609ST This fits 964 c2 / c4 and rs models with engine codes # m64.01/02/03. This is an OEM part, sourced directly from Germany. Professional installation is required. Different manufacturing tolerances require an inspection of the free clearance of all parts! If you're not sure about what parts are right for your build, be sure to ask one of our parts specialists. Sold individually. 1 necessary per car.
$1,441.00
Make a selection 96450204100EQ Quality replacement part for original number, 964 502 041 00 grv. This is made by dansk, they offer a complete line of replacement bodywork to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality, factory fitment and performance you expect for your Porsche. This commitment has made dansk one of the original equipment suppliers to the Porsche in Germany. The inner mount is adjustable to properly attach / adjust the striker plate. We recommend adding new striker plates and striker plate gaskets, left side striker plate is part # 99353102901 and the gasket is either 90153170323 or 90153170324 depending on what thickness you need. ...(choose a part on the right to read more)
$107.80
Make a selection 96450204200EQ Quality replacement part for original number, 964 502 041 00 grv. This is made by dansk, they offer a complete line of replacement bodywork to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality, factory fitment and performance you expect for your Porsche. This commitment has made dansk one of the original equipment suppliers to the Porsche in Germany. The inner mount is adjustable to properly attach / adjust the striker plate. We recommend adding new striker plates and striker plate gaskets, right side striker plate is part # 99353103001 and the gasket is either 90153170323 or 90153170324 depending on what thickness you need....(choose a part on the right to read more)
$107.80
Make a selection FVDBS352964001 Make your next brake service a breeze with our pre-packaged service kits. Quality means everything to us, so we only source these parts directly in Germany. This kit contains: 1 qty. Oem set of rear pads (4 total), part # 96535293904 2 qty. Oem brake warning sensors, part # 96461236502 4 qty. Oem brake pad damping shims (30 mm piston), part # 99635208600 4 qty. Oem brake pad damping shims (28 mm piston), part # 99635208602
$206.80
Make a selection FVDBSK351930002 Make your next brake service a breeze with our pre-packaged service kits. Quality means everything to us, so we only source these parts directly in Germany. This kit contains: 2 qty. Front rotors (zimmerman), part # 93035104700 & 93035104800 1 qty. Oem set of rear pads (textar), part # 96435193903 sold as a set. 1 necessary per car.
$471.90
Make a selection 96434705805SP We are committed to Porsche cars and are very happy to release an inner tie rod that consists of a monoball joint. Until now this was something that was really only available on racing models. Our tie rod will provide you with unequalled steering precision for street and track use. This component is manufactured in europe and contains the finest materials available, high carbon steel and 7075 t6 aluminum. Installation is seamless, this is a direct replacement for the OEM number, 964 347 058 05. We also suggest replacing your outer tie rods, we have a uniball option, our part # 96534703200sp or the OEM style, narrow body is part # 96434703200 or wide body is part # 96434703201 (qty. 2 are needed) and now is also...(choose a part on the right to read more)
$207.90
Make a selection 100555112NB German lightweight sliverknit rear seat delete / rear shelf carpet that was used on the 964 and 993 rennsport models. We go to extra lengths to ensure that our carpets are made as closely to the originals as possible. Each carpet is made with original lightweight German sliverknit and are trimmed in vinyl. Each is cut, sewn and trimmed to fit perfectly. Made in Germany. Sold individually.
$1,151.70
Make a selection 10050330000 This 9 inch front and 11 inch rear steel fender flare set is made in Germany, we offer a complete line of replacement bodywork to complement the entire Porsche model range. Sold individually. 1 necessary per car. Please note: for conversions, these flares will allow you to run 9 wide tires in the front and 11 wide in the rear. For the 964 / 965 models the torsion bar cut out must be filled. Due to variances in production at the factory, age, accident damage or rust, each part may require trimming and or adjustment for perfect fitment.
$1,648.90
Make a selection 96455550700EQ A-pillar lining made of original leatherette material, sourced and manufactured in Germany. Each is cut, sewn and trimmed for precise fitment. We go to extra lengths to ensure that our linings are as similar to the originals as possible. Replaces original part # 964 555 507 00 05t made in Germany. Sold individually. 1 necessary per car.
$94.60
Make a selection 96433102100RATK Unsure about installing a replacement bushing? Send us your trailing arm and we will properly recondition and install the bushing for you. The reconditioning process includes full inspection of your trailing arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we properly install our rear clubsport trailing arm bushings, part # FVD3310212291. Our rear trailing arm bushings contain rubber inserts with a shore hardness value of 85, like what is used on rennsport models. They offer rs style handling characteristics, superior durability and are still forgiving enough for street use. When reconditioning the trailing arms, we als...(choose a part on the right to read more)
$672.10
Make a selection 96410524707ST This fits 964 c2 / c4 and rs models with engine codes # m64.01/02/03. This is an OEM part, sourced directly from Germany. Professional installation is required. Different manufacturing tolerances require an inspection of the free clearance of all parts! If you're not sure about what parts are right for your build, be sure to ask one of our parts specialists. Sold individually. 1 necessary per car.
$1,410.20
Make a selection 96434101807ATK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we properly install our OEM front control arm bushings, part # FVD3419991. They are made with 65 shore rubber like the original control arms. Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrangements can be made for...(choose a part on the right to read more)
$418.00
Make a selection FVDBS352964002 Make your next brake service a breeze with our pre-packaged service kits. Quality means everything to us, so we only source these parts directly in Germany. This kit contains: 1 qty. Oem set of rear pads (4 total), part # 96435294903 2 qty. Oem brake warning sensors, part # 96461236502 4 qty. Oem brake pad damping shims (28 mm piston), part # 99635208602 sold as a kit. 1 necessary per car.
$137.50
Make a selection 96434307001SP Replace your old drop links to reduce body roll and rejuvenate your cars handling in the corners. Sport-version with 85 shore 964 c2 only with m030 factory sport suspension sold individually. 1 necessary per car.
$238.70
Make a selection 96410605131 This fan hub sits between the cooling fan and the alternator. It should be checked periodically for noise as it contains a bearing which can fail. Please note: 964 106 051 30 has been superseded by 964 106 051 31. If you are replacing 964 106 051 30, you will also need 3 qty., part # 90007609101 to install the new superseded hub. Sold individually. 1 necessary per car.
From $191.40
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |