Vehicles
Sections
90 not categorized PORSCHE 944S HARD PARTSCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 911 1984-86 (includes uncategorized and accessory items) 91135560501 Hard brake lines are more resilient than rubber but can develop hairline cracks after many heat cycles, stresses from service and age. The cracks will cause a loss in pressure, can corrode surrounding parts and can be a safety risk. Quality aftermarket replacement designed to perform like the original. Sold individually. 2 necessary per car. Left or right side fitment. Please note: please check the model fitment tab to ensure accurate fitment. View/Change Diagram
$25.30
Make a selection 9288030330270B High quality, German made three-point replacement safety belt, designed to perform like the original. Features / specs: belt length: 300 cm (118 inches) 3 point inertia reel belt angle adjustable reel (max. Of 8 *) includes 22 cm (8.5 inch) buckle, installation hardware and caps. Din-en-iso 9001: 2000 quality standard manufactured, e-mark approved. The matching rear belt is part # FVD85779570b sold individually. 2 necessary per car. View/Change Diagram
From $162.80
Make a selection 911604101AX If your starter is on its way out, you will notice an intermittent clicking noise and a delay in the vehicle starting. Eventually you hear a metallic screeching noise that is a sure sign that your starters bendix mechanism, bearings or solenoid are kaput. When ordering a new starter be sure to check the rubber cap on the terminal for cracks which allows moisture in and it is a good idea to check your starters hardware as well. General Fitment911 1974-77930 1975-77 911 1978-83 911 1984-86 911 1987-89 914 1970-76 911 1970-73
From $399.59
Make a selection 91163198100 High-quality OEM replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Includes mounting hardware. Sold individually. Driver's side fitment. 1 necessary per car. View/Change Diagram
From $44.00
Make a selection 91163198200 High-quality OEM replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Includes mounting hardware. Sold individually. Passenger's side fitment. 1 necessary per car. View/Change Diagram
From $44.00
Make a selection 93050305501 High-quality OEM replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. We recommend purchasing our complete kit with new installation hardware, part # 270503055 sold individually. 1 necessary per car. View/Change Diagram
From $1,135.00
Make a selection BES99105040S Perfect muffler for those looking for a more aggressive exhaust note without changing the factory catalytic converters. The added benefit is you can reuse your OEM catalytic converters for emissions purposes. + 15 hp & + 12 torque - reuses OEM cats, perfect for those concerned about warranty. - open muffler design for added power. - tubing diameter is the same as the OEM system. - weighs 19 lbs. (8,6 kg) - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - 4 on a scale of 1-10 in volume (1 being stock) below 3,000 rpms, 6 on a scale of 1-10 in volume under maximum load (3 being stock). - includes cone and v band style hardware to prevent exhaust leaks. - made in Germany. - modular desi...(choose a part on the right to read more)
$2,920.50
Make a selection 96433102100RATK Unsure about installing a replacement bushing? Send us your trailing arm and we will properly recondition and install the bushing for you. The reconditioning process includes full inspection of your trailing arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we properly install our rear clubsport trailing arm bushings, part # FVD3310212291. Our rear trailing arm bushings contain rubber inserts with a shore hardness value of 85, like what is used on rennsport models. They offer rs style handling characteristics, superior durability and are still forgiving enough for street use. When reconditioning the trailing arms, we als...(choose a part on the right to read more)
$672.10
Make a selection 96433102200RATK Unsure about installing a replacement bushing? Send us your trailing arm and we will properly recondition and install the bushing for you. The reconditioning process includes full inspection of your trailing arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we properly install our rear clubsport trailing arm bushings, part # FVD3310212291. Our rear trailing arm bushings contain rubber inserts with a shore hardness value of 85, like what is used on rennsport models. They offer rs style handling characteristics, superior durability and are still forgiving enough for street use. When reconditioning the trailing arms, we als...(choose a part on the right to read more)
$672.10
Make a selection 96437504381UNI The rs model engine mount is not a hydro-elastic mount like most models. It contains a rubber core with an 85-shore hardness value. That equates to a more responsive chassis and improved shifting response. A perfect compromise for street and track use as it is more forgiving than aftermarket solid mounts. Sold individually. 2 necessary per car. To install these mounts on any model 964 / 965 / 993 and 993 tt, we recommend our rs engine mount set that includes 2 mounts and all the mounting hardware, part # FVD375964
$218.90
Make a selection 99661298100 Let your wipers remember when to wipe the rain away. This great sensor automates the wipers into motion in this easy do-it-yourself kit. The only hard part of this installation is running the wiring from the rain sensor behind the rear view mirror to the relay box by the drivers left foot.
$421.10
Make a selection BES91100100S Brombacher exhausts are engineered for the discerning Porsche® owner and offer unmatched performance, unparalleled quality, and incredible value. All of our exhausts are manufactured in Germany and are tested comprehensively for flow rate and characteristics, thermal stress, resistance to cracking, and longevity. To further ensure quality, all of our exhaust systems meet the standards of the German independent testing agency TUV; whose quality standards are among some of the strictest in the world. General Fitment911 1978-83930 1975-77 911 1974-77 911 1984-86 911 1987-89
$6,891.50
Make a selection BES99125020SK No need for Porsche sport exhaust (pse) envy with this muffler! This offers weight savings and a far more exotic sound than the pse, all without drone. It is the perfect compromise for you and your loved ones. Rich, deep, turbo motorsport tones with the valves open and soft subtle, completely stock sounds with them closed. Top of the line or range depending on the english and is the best choice for a daily driver. Features: - + 16 crank hp & + 15 crank torque. - weighs 37 lbs. (17 kg) - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - direct bolt on replacement for the factory center muffler. - includes necessary installation hardware. - reduces turbo lag, backpressure and thermal lo...(choose a part on the right to read more)
$4,651.90
Make a selection BES99305040S FVD is proud to introduce our newest line of Brombacherexhaust systems. Brombacher exhausts are engineered for the discerning Porsche owner and offer unmatched performance, unparalleled quality, and incredible value. All of our exhausts are manufactured in Germany and are tested comprehensively for flow rate and characteristics, thermal stress, resistance to cracking, and longevity. Brombacher mufflers outer shell dampens and eliminates unwanted frequencies and ensures no resonance or drone in the cabin. The end result is a strong, linear, firing-order dominated flat-6 Porsche sound. In addition, Brombacherexhausts systems are available for ultimate performance full titanium. Our titanium system's are nearly...(choose a part on the right to read more)
$1,820.50
Make a selection CB6365 Replaces worn and defective accelerator pump diaphragm to eliminate hesitation and stumble during acceleration. Fits just like original parts. Manufactured from fuel resistant, rubber membrane with silicon bronze center plunger hardware. Fits weber 40, 44, and 48 idf early model carbs with roller on accelerator pump arm.
$10.50
Make a selection DP3103C High performance lowest dust rating pads for prestice imports and faster street driving. There are two reasons our customers love redstuff. First because they are the lowest dust pad we have encountered by reducing dust by 60-90%. Plus the minimal dust you see is very easily removed with a simple sponge was as it contains no steel fibre particles as in all other pads. Second they brake like an alligator right from cold (as good as original pads or better) and just get better as they heat up. General Fitment911 1974-77911 1984-86 911 1965-69 911 1970-73
$126.78
Make a selection E16 Rennline’s new tow hook receivers replace the factory bumper shocks with a crush style tube that the rennline’s 2 inch ”screw in” style tow hooks thread into, allowing a completely stock appearance on the street and enhanced functionality on the track. Powder-coated steel construction with stainless steel hardware, comes with black rubber bumper plug for stock appearance when hook is removed. Note: tow hooks sold separately- use part number re1309. General Fitment911 1974-77911 1978-83 911 1984-86 911 1987-89
$93.50
Make a selection FPOR1405 B&b started from scratch to offer a complete high performance exhaust system for the Porsche 911. Extensive dyno testing on their in-house dynamometer afforded us impressive horsepower and torque gains throughout the entire power band. Headers and muffler are meticulously built by hand using t304 stainless steel for a lifetime of performance - guaranteed! Included in the kit is the header set, 1.625" or 1.75" primary tube diameter, with or without heat exchangers. Their proprietary twin inlet muffler built specifically for your street or race application is also included in this complete exhaust system. The kit for the naturally aspirated Porsche 911 includes all necessary hardware, gaskets and accessroies ne...(choose a part on the right to read more) General Fitment911 1984-86911 1974-77
$3,579.69
Make a selection 90133105900 Replace worn-out rear trailing arm bushings with this OEM bushing, made of rubber with a 65-shore hardness value. 65-shore is what was originally used in all of the OEM bushings, it is quiet and comfortable for street use with street suspension. If you are looking for something sportier, try our rs bushing set, made of rubber with an 85-shore hardness value, our part # FVD33105900 sold individually. 4 necessary per car. View/Change Diagram
From $25.50
Make a selection FVD10397505CARR Carrillo is one of the most respected connecting rod manufacturers in competitive motorsports. Carrillo rods are constructed from their proprietary alloy and forged to their custom specifications. The rods are then fully machined to guarantee the removal of all surface imperfections. After heat treatment, each connecting rod is magnaflux inspected and hardness checked, then machined to final size. Each set is balanced and then shot-peened to achieve the ultimate in strength and fatigue properties. The carrillo multiphase (carr) connecting rod bolt (sps-carr-6) is a high quality, aircraft standard fastener. Each bolt is manufactured with asymmetrical threads, each thread has a slightly different design than the ...(choose a part on the right to read more)
$2,952.40
Make a selection FVD33104381 The tow link is the furthest rear control arm on the rear axle. It is responsible for the toe angle adjustment. The OEM control arm bushings are simply too soft for track events and the teflon monoball racing bushings are too far too hard and noisy for street cars. Our sport bushings are made of a denser rubber (85 shore opposed to OEM 65 shore), which means that they are suitable for street and track use. Equally as important is that they do not produce any noise like the teflon bushings. FVD sport control arm facts: - better handling and more responsive. - makes precision adjustments of the suspension easier. - does not produce noise. - shore a hardness value of 85 for durability and handling. - fit's like o...(choose a part on the right to read more)
$451.96
Make a selection FVD33105900 Replace worn-out rear trailing arm bushings with our FVD sport bushings, made of rubber with an 85 shore hardness value that is the same as the rs models. 85 shore is more durable, provides more positive suspension location and is still quiet and comfortable for street use. This is a direct replacement for original part # 90133105900 features: better handling makes precision adjustments of the suspension easier does not produce any noise like the teflon bushings. Rubber has a shore hardness value of 85 (like rs models) fit's like oem, simple installation made in Germany set is sold per axle. 1 necessary per car.
$154.00
Make a selection FVD33150040 Replace worn-out original rear sub frame (side panel) bushings and return your car to its original ride quality with this cost effective alternative. This bushing is made in Germany. It is crafted in high carbon steel and 7075 t6 aircraft aluminum and includes a 65 shore hardness value core. This is a front and rear bushing for one sub frame. 2 are necessary per car. If you are looking for a sportier upgrade we suggest our clubsport sub frame bushing set, part # FVD33150040r. We also sell complete sub frames with the bushings installed, part # FVD331993001.
$418.00
Make a selection FVD34307101 Our direct replacement, OEM quality link uses rubber with a shore hardness value of 85. That is the same value as the rennsport models from Porsche. This link will offer superior performance under high cornering loads, more durability and are still forgiving for street use. Road noise not compromised with our links either. Facts: made in Germany. Crafted from high carbon steel and 7075 t6 aircraft aluminum. Weather sealed. Sold individually. Please note: we recommend buying these as a set, please purchase the right link, our part # FVD34307201
$93.50
Make a selection FVD3511M18002A The brembo gran turismo (gt) braking system is ideal for use on the street and for light track use. This GT system expands upon the original drilled disc's face type made by Porsche. The cross drilled disc surface continuously refreshes the braking surface and offers the highest initial response of any disc type. So, you can confidently respond to sudden pedestrian or traffic movement with maximum braking performance. Drilled discs operate in a wide range of operating temperatures and environments and respond confidently in wet weather. The GT line is dedicated to the most demanding customers. It originates from racing components, consisting of floating ventilated cross drilled discs, aluminum calipers with op...(choose a part on the right to read more)
$4,394.50
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |