Vehicles
Sections
284 not categorized PORSCHE 914 MOUNTSCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 911 1984-86 (includes uncategorized and accessory items) 95137504204EQ
$42.90
Make a selection SB809192B Most other 3 point braces require you to drill and attach the third leg into the flimsy cross member behind the gas tank. Rennline has manufactured a bracket that utilizes the same mounting studs used to attach the master cylinder bracket . This mounting area is one of the strongest points on the front of your 911, giving you the optimum rigidity needed to eliminate camber change in hard cornering. Both the upper and lower bars are fully adjustable allowing you to set the desired amount of pre-stress. Constructed entirely out of aircraft grade aluminum. Fits all 911/912/930's from 1966-89. Black in color, silver shown. General Fitment911 1987-89911 1984-86 911 1978-83 930 1975-77 911 1974-77 911 1970-73 911 1965-69 912 1965-69
$265.95
Make a selection 96437502301RATK Send us your OEM transmission mount bracket and we will restore it to better than new condition! Our service includes removal of the old mount, media blasting, proper installation of the new mount and protective seal coating. Our transmission mount is manufactured in europe by an OEM supplier using the finest materials (high carbon steel, 7075 t6 aluminum and 85 shore rubber - rs spec). Simply order and send us your OEM bracket, we will take care of the rest. Approximate lead time is estimated between 3-6 weeks.
$176.00
Make a selection N0147032 Known as: pan-head screw / pan-head screw m 6 x 18 View/Change Diagram
From $3.72
Make a selection 96473131940EQ This is the mounting hinge for the sun visor. It is made of aluminum, rather than the original plastic. Sold individually. 1 necessary per car.
$23.10
Make a selection
$17.37
Make a selection M998071 A simple, yet ingenious, way to store your auto dolly sets when not in use. Works for any size dolly. By storing your dolly set on the wall you save shelf or floor space. Mounts via two lag screws to any wall stud. General FitmentACCESSORY
$51.25
Make a selection 99970326500 High-quality OEM (original equipment manufacturer) replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Please note: please check the model fitment tab to ensure accurate fitment. Sold individually. 2 necessary per car. View/Change Diagram
From $12.00
Make a selection 99970338401 Rubber mount with 6 mm stud/6 mm threaded hole for rear pump support bracket View/Change Diagram
From $7.20
Make a selection FVD37505502
$95.70
Make a selection FE02 Fire extinguishers are mandatory in all cars that will see the track and should be mandatory in all street cars. There’s no worse feeling then watching your car burn to the ground without the ability to do anything about it. Unlike most fire extinguisher mounts available, all of rennline’s mounts install directly to the factory seats and do not compromise seat travel or leg room in anyway. Constructed from aircraft grade aluminum and meets all requirements for racing series or other organized track events. Designed to be used with most standard 2.5lb fire extinguishers, all hardware and installation instructions are included. Available for both power and manual seats. Fire extinguisher not included. General Fitment911 1994-98911 1989-94 911 1987-89 911 1984-86 911 1978-83 930 1975-77 911 1974-77 911 1970-73 911 1965-69 944 1989-91 944 1985-88 944 1982-85 968 1992-95
$163.90
Make a selection BES996000000KAT When needed please order this bracket only in conjunction with bes 996 202 61s or bes 996 102 61sk
$387.84
Make a selection FVD333007 These high quality, German made mounts are made specifically for rear shock absorbers that contain a 15mm i.d. Uniball spherical bearing. They are located at the base of the rear shocks, and secure the shock to the rear trailing arms. They are required with FVD exclusive suspension kits with part #'s 115 900 911 xx / xxx. For example 115900911030 they are also required for rear shocks like part # FVD33315755 sold as a set. 1 necessary per car.
$174.90
Make a selection FVD375003 Are you experiencing vibrations in the cabin? The most likely cause is a worn transmission mount. Severely worn mounts translate to engine component wear and can even cause difficulty shifting. Our mount is manufactured in europe by an OEM supplier using the finest materials. It is a 65 shore rubber hardness value which is the same as the what was standard on these cars. Be sure to swap yours out during your next service. Sold individually. Central fitment in transmission carrier 96437502301. 1 qty. Required. Tech tip: now is the time to replace the old hardware as well. Below is a list of what is needed for installation. 1 qty. Hex head bolt m10x100 90007429202 1 qty. Lock nut m10 49020001 2 qty. Washers 10.3x...(choose a part on the right to read more)
$165.00
Make a selection FVD37504332R Replace the worn-out, original soft rubber engine mounts with our higher density, rs specification rubber bushings. These are manufactured of rubber with an 85-shore hardness value. 85-shore is the same density as what is used in the rs models. It is more durable, provides more positive, sharper shifts and offers crisper throttle response. Yet, rs spec rubber is still quiet and comfortable for street use. Features: sharper shifts crisper throttle response does not produce nvh (noise vibration harshness) like teflon or solid bushings. Rubber has a shore hardness value of 85 (like rs models) made in Germany sold as a set. 1 necessary per car.
$152.90
Make a selection FVD721102565 Lasthub elektro-hydraulisch, steuerung uber drucktasten (auf und ab), feinhub hand-hydraulisch, bei master gear 0,5/1,0 erfolgt lasthub fusshydraulisch, ablass per fussbedienung (das integrierte senkbremsventil erlaubt ein exaktes dosieren der absenkgeschwindigkeit), die variodesk-aufnahmeplatte besitzt eine verschiebbarkeit von ± 20 mm in x- und y-achse und eine neigbarkeit von ± 2* (nur master gear 1,0/2,0), aufnahmebohrungen ermoglichen die sichere befestigung fahrzeugspezifischer betriebsmittel. Aufnahmebohrungen: zusatzliche, fahrzeugspezifische betriebsmittel, lassen sich auf der tischplatte mit hilfe der durchgangigen lochmatrix stabil befestigen. Sicherheit: die grosse standflache der master gear-...(choose a part on the right to read more)
$12,784.20
Make a selection FVD3759112
$208.85
Make a selection N0101912 Known as: hexagon-head bolt / hexagon-head bolt m 12 x 1,5 x 95 / hexagon-head bolt m 12 x 95
From $6.00
Make a selection FVDMK270503
$67.20
Make a selection AFC11957 A necessary addition for any 911! This kit includes substitute 30% larger 310 matrix (14"h x 6"w x 2"d) 19 row oil cooler in a factory "hard line" equipped car. This kit is especially good for replacing the factory "loop" oil device located in the front right fender, making it easy to upgrade to a mocal oil radiator at an economical price. Includes the cooler, two 90 degree 3/4 fittings, two 30 mm straight fittings, and a 3/4 oil hose. this is larger than out basic oil cooler kit. Note: for car that already have a factory oil cooler. General Fitment911 1974-77930 1975-77 911 1978-83 911 1984-86 911 1987-89
$475.00
Make a selection
$28.22
Make a selection
$30.46
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |