PORSCHE 924 S SILL RIGHTCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 911 1989-94 - Front Axle/Steering (includes uncategorized and accessory items) 96434703200 If your outer tie rods are worn you will experience sloppy steering response and knocking / creaking sounds. Your outer tie rods keep the steering centered, so failure can be very dangerous and can seriously affect steering control. Prevent that from happening by replacing them as quickly as possible with our genuine replacement inner tie rods. Once you do, you will experience tighter, more precise feedback without noise. Complete kit consists of: 1 qty. Tie rod 1 qty. Hexagon nut (m14 x 1.5) 1 qty. Ball joint end 1 qty. Lock nut & pin sold individually. Left or right side fitment. 2 qty. Required. Tech tip: replace the inner tie rods also for a new car steering feel ! Purchase our part # 96434705804 & 96434719...(choose a part on the right to read more) View/Change Diagram
From $55.29
Make a selection FVD33150005 Restore proper suspension geometry with this adjustable lower rear control arm. The factory control arm cannot compensate enough when lowering your Porsche, leaving you with as much as ½ inch of toe in. The result is poor handling and rapid tire wear. This kit will provide the additional adjustment needed. The adjusting link has a left and right hand thread on each end. Rotating the link will increase or decrease the overall length of the arm. A precision teflon lined spherical rod end replaces the compliant rubber factory bushing for improved suspension response and feedback, and also reduces toe changes during acceleration and deceleration. Sold in pairs. 1 necessary per car.
$764.50
Make a selection FVD33150003 Rear toe control arms - order in pairs only restore proper suspension geometry with this adjustable lower rear control arm. The factory control arm can't compensate enough when lowering your Porsche, leaving you stuck with as much as ½ of toe in. The result is poor handling and rapid tire wear. This kit will provide the additional adjustment needed. The adjusting link has a left and right hand thread on each end. Rotating the link will increase or decrease the overall length of the arm. A precision teflon lined spherical rod end replaces the compliant rubber factory bushing for improved suspension response and feedback, and also reduces toe changes during acceleration and deceleration.
$218.90
Make a selection 96434350500 A cracked boot will allow dirt and debris to score the shock shaft which causes premature leaking and failure. We recommend replacing the bellows when installing a new shock absorber. Sold individually. Right or left side fitment. 2 necessary per car. Please note: if you are installing new shocks, we sell a complete kit containing front bellows and bump stops, part # FVD34350501 View/Change Diagram
From $30.80
Make a selection GR5006 Leather upholstery belongs in all fine cars. It just smells and feels right. Preserve your expensive handsome interior with the best! Lexol cleaner is ph balanced, so even with its fantastic cleaning abilities, it will not cause your leather to dry or crack. A good cleaning should then be followed with lexol conditioner to restore the suppleness and keep the leather from drying out (especially in the summer sun). General FitmentACCESSORY
$13.49
Make a selection FVD631601B Update the look of your car to a brighter and more modern look. This bulb emits a brilliant blue-white light which also enhances safety on our older cars. This bulb is intended for fog or corner lighting. Lighting is a key component of safety. Be sure that your exterior and interior bulbs are in good working order. This bulb can be used as an alternative to part # 90063112690 sold individually.
$23.10
Make a selection FVD512997GT3RST 997 GT3 rear spoiler fits 997turbo includes: deck lid, aluminum upright, 3rd brake light housing and kevlar/carbone wing (l= 145cm, b=28cm, h=7 cm) with end plates. Material: aluminum, fiberglass, kevlar-carbone. Also available with wing blade in fiber (gfk) FVD512997gt3rs tech tip: facelift models (2009- ), the 3rd brake light can usually be assumed. If necessary please order the 3rd brake light 99763105201 separately. The holes for the intake fan on the rear deck lid must be drilled prior to installation (model variations). Please note wing is fixed and is not adjustable. The air inlet of the rear is not included. Please order 99751262592g2x
$6,528.50
Make a selection 99334703181 If your tie rod is worn, you will experience sloppy steering response and knocking / creaking sounds. Your tie rod keeps the steering centered, so failure can be dangerous and can seriously affect steering control. After replacing the tie rods, you will experience tighter, more precise feedback without noise. Tie rod consists of: 1 qty. Tie rod 1 qty. Hexagon nut (m14 x 1.5) 1 qty. Inner axial joint 1 qty. Lock nut we recommend replacing the right and left side tie rods at the same time. We also recommend replacing the bellows, part # pcg419831c sold individually. 2 necessary per car.
From $303.00
Make a selection GR6031 Nothing ruins the appearance of a sharp set of wheels like dirty, corroded calipers lurking from behind. General FitmentALL
$40.95
Make a selection GR6036 Nothing ruins the appearance of a sharp set of wheels like dirty, corroded calipers lurking from behind. General FitmentALL
$52.95
Make a selection CB43201B Corbeau 2 inch double release harness belts are unique in that they have a disconnect feature between the front shoulder straps and the rear tail strap. This feature allows for easy access to the rear seat as you can disconnect that rear strap without taking the belts out. They also have the rare ability to be bolted to all your factory provided mounting points. What that means is all our hardware was manufactured to bolt right up to your factory bolt holes. In most cases no drilling or modifications are necessary, they just bolt right in. Corbeau 2-inch double release harness belts are available in a 3 point style with bolt-in mounting. General FitmentALL
$169.00
Make a selection 91153170202 As a striker plate ages, it will start to rattle and can potentially be a safety risk. We recommend securing them with new oval head screws, part # 99921900800. 2 screws are needed per plate. We also recommend adding new striker plates gaskets, either 90153170323 or 90153170324 depending on what thickness you need. This line is a high-quality replacement part, sourced in Germany and designed to perform like the original. Sold individually. 1 necessary per car.
From $133.10
Make a selection 115343993008R If you are looking for a shock to combine with lowering springs or firmer springs the bilstein b8 is the ideal solution. These offer more performance than the b6 as the valving is more firm. These will pair well with h&r or eibach lowering springs, however you can also run them with euro mo30 (row) springs and mo33 springs. The product benefits at a glance: shortened high-performance shock absorbers for virtually every lowering spring set. Marked improvement in safety and sportiness with additional spring changes (lowering). Sporty feel, yet still comfortable. Offers precise handling and optimum control. Bilstein gas pressure technology. Bilstein mono-tube/upside-down technology. Made in Germany. Road-tested an...(choose a part on the right to read more)
$524.70
Make a selection FVD34101807AT By ordering this article number, you will receive a reconditioned wishbone with newly pressed-in bearings. The calculated replacement deposit will be returned to you as soon as the old part has been received and checked. The reconditioning process includes full inspection of each track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we properly install our OEM front control arm bushings, part # FVD341999r. They are made with 65 shore rubber like the original control arms. If your old part is not repairable we will inform you immediately. General Fitment911 1989-94
From $418.00
Make a selection FVD34101802RAT We will send you a reconditioned control arm, kindly send back your old part, or core . The reconditioned control arm has been full inspected, disassembled, degreased and we have properly installed FVD race front control arm bushings. They are made with uniball bearings so suspension motion is accurately repeated in every corner please note: each control arm is remanufactured in Germany, so the lead times can vary. This part is sold on an exchange basis, as such an additional charge (a core deposit) will be added to the purchase price of the part. After receiving your new part, kindly send back your old part, or core . Once the core is returned to us and it has been inspected to ensure it is rebuild-able and re...(choose a part on the right to read more)
$440.00
Make a selection 96434101807AT By ordering this article number, you will receive a reconditioned wishbone with newly pressed-in bearings. The calculated replacement deposit will be returned to you as soon as the old part has been received and checked. This item is also available with race bearings (85 shore).article number FVD 341 018 07at the reconditioning process includes full inspection of each track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we properly install our OEM front control arm bushings, part # FVD3419991. They are made with 65 shore rubber like the original control arms. If your old part is not repairable we will inform y...(choose a part on the right to read more)
$418.00
Make a selection 96434307281ATK Looking for a more cost-effective solution than ordering a new link? Let us recondition your original drop link. The reconditioning process includes full inspection, disassembly, degreasing and media blasting. Once fully prepared, we properly install new bushings, finish with a corrosion proof coating and include a new lock nut. Please note: each link is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your link we will notify you as soon as we can. Arrangements can be made for its return to you. Sold individually. 1 necessary per car.
$194.70
Make a selection 96453109600EQ This is a genuine door seal that seals the entire door and window frame. As these classics age the original gasket can become brittle and will crack, so it is essential that it is in good order as it keeps moisture out of the cabin. Sold individually. 1 necessary per car.
$215.60
Make a selection 91134190200ATK By ordering this part number you get after previous sending in, your wishbone overhauled with new silent blocs. Order separately if required 901 341 049 04 or 911 341 049 05 to. Should it not be repairable, we will inform you immediately.
$276.10
Make a selection FVD11104001 These headers are meant to replace the original 993 GT2 r (993 111 039 83) headers that are no longer available. They will reduce turbo lag and add horsepower and torque. Made of t316 stainless. Primaries are 42mm (1.65 ). Merge into a 50mm (2 ) motorsports collector. Manufactured by m&m exhaust in Germany.
$1,835.90
Make a selection FVD123048 FVD Brombacher997.2 tt "700 series" upgraded turbos facts: - modified compressor housing for the 3.8 l displacement - modified & lightened billet compressor wheel with 12 blades - 49.55 mm inducer - 68 mm exducer - remanufactured by borg warner certified technicians - shaft tolerances are strictly maintained to ensure durability - free software update for those already running FVD software we start by re-profiling the OEM vtg turbocharger compressor housing and modifying the compressor backing plate. This is done to replace the factory compressor wheel with a larger 12 blade, modified compressor wheel. The larger wheel is also lightened allows the turbo to flow a larger volume of air (more power), and aids i...(choose a part on the right to read more)
$6,413.00
Make a selection FVD34102800ATK By ordering this part number you get after previous sending in your wishbone overhauled with new race-silent blocs back. The race-silent blocs (85 shore) give you more stable driving. Should it not be repairable, we will inform you immediately.
$279.40
Make a selection 99333105280 The bushings are made of rubber with an 85-shore hardness value, which is more durable, provides more positive suspension location and is still quiet and comfortable for street use. Sold individually.
From $764.50
Make a selection FVD123014 K-16/24 turbo (up to 555 hp) power is focused on low and mid-range rpm's. Facts: larger compressor wheel with extended tip. 47.5mm inducer diameter. Cnc modified compressor housing modified and improved back plane uprated staggered gap turbine uprated thrust bearing modified wheel to reduce backpressure balancing of all components factory vacuum unit new bearings and seals all parts are reconditioned and balanced FVD Brombacher993 k-16/24 new turbos are created for those who are looking for power that is focused in the low and mid rpm range. They are completely bolt on and do not require custom headers or special modifications. The process starts with re-profiling the OEM turbocharger compressor housing and m...(choose a part on the right to read more)
$2,976.60
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |