Vehicles
Sections
44 not categorized PORSCHE CAYENNE TURBO REP SETCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 911 1989-94 (includes uncategorized and accessory items) 22011099706 The 997 turbo ipd "y" pipe was built for the more demanding turbo performance customer. The factory y pipe becomes restrictive when adding substantial power gains. The ipd "y" pipe has larger inlets and an optimized diversion area allowing for even greater power gains. This superior and more efficient design flows 126 more cfm than the factory y pipe delivering the additional power needed to raise the performance bar on any turbo. The ipd "y" y pipe is designed to be a direct replacement of the factory OEM y pipe. There are no modifications or fabrication required for installing the ipd y pipe. This is an easy and straight forward r & r (remove and reinstall) bolt on upgrade. Note: contains everything nec...(choose a part on the right to read more)
$1,182.06
Make a selection BES99715040S2 Quiet version with catalytic bypass and 4x80mm end tips these versions of FVD sport exhaust system is specifically made for increased performance vehicles. Designed for tolerable, pleasant and sonorous sound (especially for the turbo cabriolet). The elimination of the catalysts reduced drastically the back pressure and increases the performance and throttle response to the max! - stainless steel exhaust system - catalytic bypass - 4x80mm end tips - 2 3/4 tubing (70mm) straight through design for maximum power - weighs 39 lbs. (18,1 kg) - made in Germany - dme programming necessary (catalytic adaption) - stock tips will fit. Tech tip: order also repair / gasket set FVD mk9 970 02
$3,162.46
Make a selection 99919234350EQ Belts undergo a lot of friction and wear. They are cost effective to change and will keep your alternator and engine in good condition. Be sure to follow recommended service and replacement intervals set by Porsche on belts. For 964 c2 tip trans. / 993 tip trans. / 993 c2/ s manual trans. And the 993 turbo. Sold individually. 1 necessary per car.
$11.88
Make a selection 1661900310 A quality, cost effective set of replacement "big red" style calipers. These are a direct replacement for the 965 turbo, 993 c4s / rs and 993 turbo but can be installed on many 964 / 993 models with the correct caliper adapters. We also recommend swapping out your brake lines for a set of stainless braided lines when replacing calipers. Please note: these are aftermarket calipers and do not come with the logo or brake pads. General Fitment911 1965-69911 1970-73 911 1974-77 930 1975-77 911 1978-83 911 1984-86 911 1987-89 911 1989-94 911 1994-98
$858.60
Make a selection FVD500964965 This kit contains everything necessary to transform your narrow body c2 or c4 into a 965 wide body / turbo look. It includes motorsport quality glass-reinforced plastic (grp) front + rear bumper and side skirts along with metal fender flares. General Fitment911 1989-94
$7,730.99
Make a selection FVD51299122MM The moshammer vented rear diffuser with fins is an aggressive design that reduces aerodynamic drag. This vented diffuser allows air that is trapped by the rear bumper to exit, allowing for greater top end performance. The design also incorporates 5 fins that improve laminar airflow by reducing turbulence. Moshammer manufactured this as a direct replacement, so it secures seamlessly to the factory locations with the original hardware. This is an ideal addition for a leased vehicle or for those looking to return the car to its original appearance in the future. When added to other elements of the evo rs (991.2 turbo/s) package, the result is a confident, cohesive stance with balanced downforce. Features: vented f...(choose a part on the right to read more)
$1,992.28
Make a selection BBI9911070001 The bbi autosport intercooler kit is a direct replacement upgrade for the Porsche 991 turbo. Designed with 3d modeling & computational fluid dynamics software, this bespoke intercooler features 3d printed and cfd tested end tanks, and offset cores for optimum flow and improved performance. The advanced 3d printing manufacturing process allows complex design and shapes to be produced for optimum flow. This kit is ready for installation (plug & play), using the stock plumbing and shrouds. When engineering, technology, and the right people are fueled by passion, the results are impressive.
$4,746.60
Make a selection FSPOR992SC Purchase disclaimer: fabspeed motorsport does not condone the use of emission defeat devices for any vehicles used on public streets or roadways. Fabspeed motorsport will not tamper, remove, disable, or bypass emissions equipment on a motor vehicle in accordance with 40 cfr section 86.1854.12(a)(3), clean air act 40 cfr 1068.101(b). This includes software, known as tunes, that reprogram a motor vehicles electronic control module to alter engine performance and enable the removal of filters, catalysts, and other critical emissions controls.
$3,991.63
Make a selection FVD351425426EQ A quality, cost effective set of replacement "big red" style calipers. These are a direct replacement for the 965 turbo, 993 c4s / rs and 993 turbo but can be installed on many 964 / 993 models with the correct caliper adapters. Please contact your FVD parts specialist for fitment questions. We also recommend swapping out your brake lines for a set of stainless braided lines when replacing calipers. Also a now is the time to install a set of our speed bleeders, part # FVD910102. They are comparable to part numbers 993 351 425 10 and 993 351 426 10. Please note: these are aftermarket calipers and do not come with the logo or brake pads. Sold individually. 1 necessary per car.
$944.46
Make a selection FVD504993RS Made of polyurethane so they will not chip or crack like fiberglass, and are flexible enough to survive small impacts. Simple installation without any modifications to the original bodywork. Sold as a set (left and right). Not for wide body cars (993 turbo or turbo-look). Please note: these are aftermarket products. All aftermarket products need to be prepped, sanded, gaps checked / filled and painted. We only recommend professional installation with a shop that has aftermarket bodywork experience.
$752.00
Make a selection FVD51299102MM The moshammer vented rear diffuser with fins is an aggressive design that reduces aerodynamic drag. This vented diffuser allows air that is trapped by the rear bumper to exit, allowing for greater top end performance. The design also incorporates 5 fins that improve laminar airflow by reducing turbulence. Moshammer manufactured this as a direct replacement, so it secures seamlessly to the factory locations with the original hardware. This is an ideal addition for a leased vehicle or for those looking to return the car to its original appearance in the future. When added to other elements of the downforce rs (991.1 turbo/s) package, the result is a confident, cohesive stance with balanced downforce. Features: ve...(choose a part on the right to read more)
$1,577.66
Make a selection 115110015 Lower your ride height up to 1.5 inches (40mm) by simply replacing the spring plate. This spring plate set the spring 1.5 inch lower. Factory shock and spring can be used. This leaves the damping and spring characteristics original even the car is lowered. Please note: only for shocks with a diameter of 61.85 mm at the threads. This will not fit mo30 suspension (i.e. Shock part #'s 965 343 041 05 / 965 343 042 05). This cannot be used on bistein b6 and hd shocks. Sold individually! 2 required for the front axle. General Fitment911 1994-98911 1989-94
From $81.97
Make a selection FVD111LAMVER Having problems with your check engine light? Want to run cat bypass pipes or a free flowing sports catalyst set up on your vehicle without having to reprogram the dme (ecu)? This adapter offsets the oxygen sensor about 1.5 inch from the gas stream. This achieves, in most cases, a sufficient measurement for the air/co ratio and increases the tolerance range between the pre and post cat oxygen sensors. In addition, the sensitivity of the oxygen sensor is also reduced allowing you to run a nearly any exhaust or catalytic set up, including bypass pipes, without the need to reprogram your ecu! Use only for the 2nd oxygen sensor (after catalytic)! General FitmentBOXSTER 1997-04911 GT3 2007-11 911 2005-08 911 GT3 2003-05 911 TURBO/GT2 2001-05 911 1998-05 911 1989-94 911 1987-89 911 1984-86 911 1978-83 CAYENNE 2007-10 CAYENNE 2003-06 CAYMAN 2006-08 BOXSTER 2005-08 968 1992-95 944 1982-85 944 1985-88 944 1989-91 928 1992-95 928 1987-91 928 1983-86 924 1986-88 924 1980-85 911 1994-98
$46.33
Make a selection 24135196501RS Highlights: made for up to 750*c (1,382*f) for street, some track use and rally use. Low dust, high performance street pad with 20-25% % brake improvement. Capable of repeated heavy brake use without brake "fall-off". Very minimal disc/rotor damage characteristics. Features red "brake in' surface coating for instant safe braking after install. Superb material for European cars. Ece r 90 type approved for most cars. High performance lowest dust rating pads for prestige imports and faster street driving. Redstuff reduce dust by 60-90%. Plus the minimal dust you see is very easily removed with a simple sponge wash as it contains no steel fibre particles as in all other pads. Second they brake like an alligator...(choose a part on the right to read more) General Fitment911 GT3 2003-05911 1994-98 911 1989-94 928 1992-95
From $287.50
Make a selection 24135196501BS Highlights: General Fitment911 GT3 2003-05911 1994-98 911 1989-94 928 1992-95
$208.28
Make a selection 210111965002 Our exhaust products are engineered for the discerning Porsche owner and offer unmatched performance, unparalleled quality, and incredible value. Our entire "brombacher" line of exhausts is manufactured by m&m exhaust, gmbh in Germany who is no stranger to Porsche racing exhausts. Each is tested comprehensively for flow rate, thermal stress, resistance to cracking, and longevity. To further ensure quality, the exhaust material (t 316 stainless) meets the standards of the German independent testing agency TUV; whose quality standards are among some of the strictest in the world. - + 15 crank hp & + 13 crank torque. - 2 3/4 tubing (70mm) for maximum power. - weighs 6.61 lbs. (3 kg). - catalytic look. - German v...(choose a part on the right to read more) General Fitment911 1989-94
From $508.46
Make a selection 21011196500 Our exhaust products are engineered for the discerning Porsche owner and offer unmatched performance, unparalleled quality, and incredible value. Our entire "brombacher" line of exhausts is manufactured by m&m exhaust, gmbh in Germany who is no stranger to Porsche racing exhausts. Each is tested comprehensively for flow rate, thermal stress, resistance to cracking, and longevity. To further ensure quality, the exhaust material (t 316 stainless) meets the standards of the German independent testing agency TUV; whose quality standards are among some of the strictest in the world. - + 15 crank hp & + 13 crank torque. - 2 3/4 tubing (70mm) for maximum power. - weighs 5 lbs. (2.3 kg). - sleek single pipe design to...(choose a part on the right to read more) General Fitment911 1989-94
From $494.21
Make a selection M18MOUNT The rennline tunable engine mount for the Porsche 964 offers the ultimate in adjustability for your car. Replacing your compliant factory mounts will decrease engine movement resulting in better acceleration, handling and significantly increased shifter feel. This is the ultimate solution for almost any car, and allows you to tune our mounts for the way you drive.these mounts are cnc machined from billet aluminum and include three pairs of inserts in varying densities. Tune your mounts by using the softer inserts to reduce engine slop and avoid missed shifts in your street car, or utilize the stiffest inserts to get the most from a more focused track car. You can even mix and match, giving you 9 possible combin...(choose a part on the right to read more) General Fitment911 1989-94BOXSTER 1997-04 BOXSTER 2005-08 911 1998-05 911 TURBO/GT2 2001-05 911 2005-08 911 GT3 2007-11 911 TURBO/GT2 2007-09 911 2009-12
$510.30
Make a selection 115110016 For bilstein b16/hd shock: General Fitment911 1989-94
$81.97
Make a selection SP01B It’s time to replace those weathered, beat up plastic sill plates that the factory installed on your car. If you’re going to replace them, why not add some style and a racy attitude to your sills? Rennline sill plates are by far the nicest sill plates on the market. Constructed of 300 series stainless steel with a black finish. Sold as a set of 2. General Fitment911 1974-77930 1975-77 911 1978-83 911 1987-89 911 1984-86 911 1965-69 911 1970-73 911 1989-94 911 1994-98
$165.13
Make a selection F6564120105 Instrument faces are one of the most visible and frequently looked at components in your Porsche. When making the decision to change them you want to make ensure that you select a high quality product similar to your originals. Each of our sets are made in Germany and use the factory scripting (font). Our faces also offer the same uniform night time shading and includes the original die cut notches for easy installation. Each kit is made for global distribution, so simply pick out the faces that match your originals. They are available in a variety of colors to make a bold statement, or to match exterior paint schemes. This kit includes faces for: manual transmission / tiptronic transmission / kph / mph / celsi...(choose a part on the right to read more) General Fitment911 1989-94911 1994-98
$652.21
Make a selection F6564120101 Instrument faces are one of the most visible and frequently looked at components in your Porsche. When making the decision to change them you want to make ensure that you select a high quality product similar to your originals. Each of our sets are made in Germany and use the factory scripting (font). Our faces also offer the same uniform night time shading and includes the original die cut notches for easy installation. Each kit is made for global distribution, so simply pick out the faces that match your originals. They are available in a variety of colors to make a bold statement, or to match exterior paint schemes. This kit includes faces for: manual transmission / tiptronic transmission / kph / mph / celsi...(choose a part on the right to read more) General Fitment911 1994-98911 1989-94
From $452.20
Make a selection DH03B Often used and abused, it’s not uncommon for the inside door handles to be worn, brittle, and have broken. If your handles need replacing, why not upgrade and add some racing moxie to your 911? Rennline makes these aluminum handles in perforated aluminum that add that extra style to your interior. Sold in black and as a set of two. General Fitment911 1974-77930 1975-77 911 1978-83 911 1984-86 911 1987-89 911 1989-94
$188.89
Make a selection SP01 It’s time to replace those weathered, beat up plastic sill plates that the factory installed on your car. If you’re going to replace them, why not add some style and a racy attitude to your sills? Rennline sill plates are by far the nicest sill plates on the market. Constructed of 300 series stainless steel with a brushed silver finish. General Fitment911 1974-77930 1975-77 911 1978-83 911 1987-89 911 1984-86 911 1965-69 911 1970-73 911 1989-94 911 1994-98
$156.60
Make a selection 993555031700EQ This is an original replacement door panel that is a perfect reproduction made in Germany. Features: period correct material with the correct graining water resistant fiberboard base layer of sound absorption foam perforations are die cut for superior fitment made in Germany sold individually. 1 necessary per car. If you would like a set, the passengers side is part # 993555032700eq
$373.03
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |