![](https://30ed524141d0cac60ab4-d2e2d18a14257de3b9ce428cf077ee97.ssl.cf2.rackcdn.com/acban.jpg)
PORSCHE 944 SUSPENSION KITSCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 911 1989-94 (includes uncategorized and accessory items) ![]() 11590099101 This suspension cancellation kit eliminates the Porsche active suspension management (pasm) warning light and persistent trouble codes when installing a conventional suspension kit. The functioning of the of the electronic control unit remains completely intact and Porsche dynamic chassis control (pdcc) is also fully functional. Warning: if the pasm is switched off with the Porsche tester (pwis), the pdcc is also deactivated!
$506.00
Make a selection FVD33396411 A cost effective FVD exclusive combination of bilstein clubsport shocks with a set of eibach pro kit springs. This suspension kit is meant for those who want the car to sit at the lowest possible ride height. This set up will allow you to lower the front axle by 2.4 inches (60 mm). This is a perfect kit for clubsport or race use where the surfaces are smooth and even. The stock rs ride height was 1.6 inches (40 mm) lower. So, this is a full 3/4 of an inch (20 mm) lower on the front axle. Sold as a complete kit. 1 kit is necessary per car. Please note: we recommend the b6 / ohlins suspension kits for those looking for more comfort for street use.
$2,616.16
Make a selection 29813 Sport spring kits are h&r's number one selling product. Enhance the look of your vehicle with a reduced fender well gap. H&r sport springs lower the vehicle center of gravity and reduce body roll for better handling. The progressive spring rate design provides superb ride quality and comfort. A lower wind resistance signature will make the vehicle more streamlined and improve gas mileage. If you are only looking to improve one part of your vehicle's suspension, you cannot go wrong with installing sport springs. Fun to drive, h&r sport springs are the number one upgrade for your vehicle. General Fitment911 1989-94
$451.35
Make a selection FVD3439641PSS9 The FVD camber plate kit replaces the front and rear original rubber top strut mount bushings. We manufacture each camber plate and mount in Germany and machine each from a solid block of billet aluminum. Each is fitted with spherical bearings which allows a wide range of camber possibilities. This kit contains: 2 front camber plates 2 rear camber plates please note: this kit only works in conjunction with a pss9 / pss10 coil over (double spring) suspension in front and rear. General Fitment911 1989-94
From $1,245.20
Make a selection 7201140 The eibach pro-kit is the perfect answer for most frequently-driven street cars. It;s eibach;s legendary spring system that dramatically improves both a vehicle;s performance and appearance. General Fitment911 1989-94
$507.76
Make a selection 115900993BI The bilstein b16 (pss10) suspension kit is the ultimate race inspired suspension system, delivering unsurpassed driving performance in any situation. This suspension kit puts you in complete control, providing the kind of precise suspension tuning formerly available only on race cars. From a weekend of competition to daily driving, this system provides perfect handling performance for every situation. The manually adjustable damping mono-tube gas shock absorbers feature 10-stage precise compression and rebound settings, from comfort to competition. The bilstein b16 (pss10) suspension kit utilizes debris resistant round threads on these dampers to ensure spring adjustment remains effortless throughout the life o...(choose a part on the right to read more)
$4,341.70
Make a selection P911830 This is a true, 935-style spring plate design for the c2/4. Under hard cornering, rubber mounted suspension points can deform effecting critical angles of camber and toe. Erp/weltmeisters spring plates incorporated heim-joint linkage for precise suspension movement, a necessity for high speed handling and stability. The plates have also been designed to be mounted either right-side up or upside-down, offering a larger number of alignment settings. General Fitment911 1989-94
$795.99
Make a selection FVD3310212291 Our rear trailing arm bushings contain rubber inserts with a shore hardness value of 85, like what is used on rennsport models. It offers rs style handling characteristics, superior durability and is still forgiving enough for street use. - better handling. - makes precision adjustments of the suspension easier. - does not produce road noise. - shore hardness value of 85. - direct OEM replacement. - more forgiving for street use. -includes press tools and grease for easier assembly. Sold as a set. 1 kit is necessary per car. Please note: this fits the 964 c2 / c4 and rs america. Not keen on installing or having the bushings installed at a shop? Please check out our part # FVD33399603b8 and FVD33399603b8, we wil...(choose a part on the right to read more)
$902.00
Make a selection FVD33150030 This kit is complete and includes a total of 8, 4 smaller and 4 larger for the rear control arms. Our weather sealed monoball cartridges are crafted in high carbon steel and 7075 t6 aircraft aluminum. They will positively locate the suspension arms so suspension motion is accurately repeated in every corner. Sold as a set of 8. 1 kit is necessary per car. Please note: noise may resonate inside the cabin during street use.
$746.90
Make a selection FVD333007 These high quality, German made mounts are made specifically for rear shock absorbers that contain a 15mm i.d. Uniball spherical bearing. They are located at the base of the rear shocks, and secure the shock to the rear trailing arms. They are required with FVD exclusive suspension kits with part #'s 115 900 911 xx / xxx. For example 115900911030 they are also required for rear shocks like part # FVD33315755 sold as a set. 1 necessary per car.
$174.90
Make a selection FVD33150003 Rear toe control arms - order in pairs only restore proper suspension geometry with this adjustable lower rear control arm. The factory control arm can't compensate enough when lowering your Porsche, leaving you stuck with as much as ½ of toe in. The result is poor handling and rapid tire wear. This kit will provide the additional adjustment needed. The adjusting link has a left and right hand thread on each end. Rotating the link will increase or decrease the overall length of the arm. A precision teflon lined spherical rod end replaces the compliant rubber factory bushing for improved suspension response and feedback, and also reduces toe changes during acceleration and deceleration.
$218.90
Make a selection FVD3439642PSS9 The FVD camber plate kit replaces the front and rear original rubber top strut mount bushings. We manufacture each camber plate and mount in Germany and machine each from a solid block of billet aluminum. Each is fitted with spherical bearings which allows a wide range of camber possibilities. This kit contains: 2 front camber plates 2 rear camber plates please note: this kit only works in conjunction with a pss9 / pss10 coil over (double spring) suspension in front and rear. General Fitment911 1989-94
From $1,204.50
Make a selection M500072 Moton club sport damper system Porsche 993 93-98 General Fitment911 1989-94
$7,356.15
Make a selection M500012 Moton club sport damper system Porsche 964 89-93 General Fitment911 1989-94
$7,356.15
Make a selection FVD33396500 A cost-effective combination of bilstein b6 shocks with a set of German h&r lowering springs. This kit is a perfect balance of performance and comfort for street use. Benefits: optimum adhesion and enhanced stability for daily driving and extreme driving situations. Lower stance at 1.3 inches (35 mm) front / 1.18 inches (30 mm) rear. Marked improvement in safety and sportiness. Bilstein gas pressure technology. Bilstein mono-tube/upside-down technology. Made in Germany. Please note: if you would like to reduce the ride height, please order part # 115110016 which will lower the stance by another 1.5 inches (40mm).
$2,730.94
Make a selection FVD33396400 A cost-effective combination of bilstein b6 shocks with a set of German h&r lowering springs. This kit is a perfect balance of performance and comfort for street use. Benefits: optimum adhesion and enhanced stability for daily driving and extreme driving situations. Slightly lower stance at 1.3 inches (35 mm) front / 1.18 inches (30 mm) rear. Marked improvement in safety and sportiness. Bilstein gas pressure technology. Bilstein mono-tube/upside-down technology. Made in Germany. Please note: if you would like to reduce the ride height, please order part # 115110016 which will lower the stance by another 1.5 inches (40mm).
$2,708.92
Make a selection 11595B00EIB Lowering up 30mm, front axle load 1290kg / 1340 rear, 1475 kg with trailer operation. Not for vehicles with level control/air suspension.
$686.40
Make a selection 11595B01EIB Lowering up 30mm, front axle load 1290kg / 1340 rear, 1475 kg with trailer operation. Not for vehicles with level control/air suspension.
$686.40
Make a selection FSBA22 The light-weight hollow sway bars are half the weight of a solid bar with the same stiffness. they are fabricated from aircraft-quality 4130 chrome moly alloy steel and heat treated to maximize strength and reliability.
$495.00
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |