Vehicles
Sections
86 not categorized PORSCHE CAYENNE TURBO PORSCHE KINCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 911 1989-94 (includes uncategorized and accessory items) 930123002X This remanufactured turbo is a direct replacement for original part # 930 123 002 00. The remanufacturing is completed in Germany by kkk/borg warner certified technicians. This ensures reliability, superior performance and cost effectiveness. The remanufacturing process includes: complete disassembly. All parts are cleaned, inspected and measured for tolerances. Turbine wheels are replaced. Thrust bearings are replaced. All new seals are installed. Internals are reconditioned. Parts are balanced (static & dynamic) according to balancing protocol. For a complete installation we recommend adding a gasket, part # 93012319105 an intake sleeve, part # 93011015801 and be sure to have a few spare studs on hand, part #...(choose a part on the right to read more)
From $2,981.74
Make a selection EIP002ME20 Endless ewig me20 racing rear brake pads Porsche 964 turbo 91-92 General Fitment911 1989-94
$526.50
Make a selection BBI9964010006 Finally, a solution that allows you to safely increase without the risk of damaging your front axles. as you add GT3 shims to your front Porsche 996/997 turbo lower control arms, you move the cv joints beyond their safe range of motion, risking failure and expensive damage. These 10mm thick precision spacers, used with 16mm of lca shims will provide an additional -1.7 deg. Of camber, while maintaining the factory cv joint and axle relationship. the spacer design features a concentric lip that positively and accurately locates it to the cv joint for perfect balance and no vibration. Each kit includes two spacers and all the needed hardware in high class 10.9 grad
$375.00
Make a selection 99312301352ATK Our k-16 remanufactured turbo is cost competitive and is a direct replacement. Simply send us your original k16 turbochargers and a borg warner / kkk certified technician will remanufacture your turbo. The remanufacturing process includes full inspection to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will replace the turbine wheels, thrust bearings, install new seals, install new waste gates, recondition the internals and high speed balance the turbo. This ensures reliability and superior performance for many years to come. The remanufacturing is done on an exchange basis only. You must send us your original k16 turboc...(choose a part on the right to read more)
$2,194.50
Make a selection EIP000MX72 Endless ewig mx-72 front brake pads Porsche 993 turbo 93-97 General Fitment911 1989-94
$499.50
Make a selection BK83760293 This comprehensive book is dedicated to the revolutionary Porsche 911s built between 1989 and 1994, known to aficionados and factory insiders as auftragsnummer 964 (project number 964). Porsche 911 enthusiast's companion™ covers Carrera 2, Carrera 4, and turbo models from 1989 to 1994. Whether you're a 964 owner, a prospective buyer, or a Porsche workshop technician looking for 964 information, this is an invaluable addition to your technical library. General FitmentACCESSORY911 1989-94
$85.00
Make a selection EIP001N35S Endless ewig n35s racing front brake pads Porsche 964 turbo 91-92 General Fitment911 1989-94911 1994-98
$526.50
Make a selection EIP001ME20 Endless ewig me20 racing front brake pads Porsche 964 turbo 91-92 General Fitment911 1989-94911 1994-98
$526.50
Make a selection FVD50499101MM The moshammer side inlet set is a striking design that enhances performance and efficiency. The inlets create a ram air effect by scooping in a larger volume of air, which delivers up to 10% more air pressure into the intercoolers. These sets are available in satin black, gloss black or high gloss carbon. This is another versatile moshammer offering for a leased vehicle or for those looking to return the car to its original appearance in the future. This set complements the entire moshammer downforce rs (991.1 turbo/s) or evo rs (991.2 turbo/s) aero packages and benefits the mighty GT2 rs as well. Features: striking design increased performance added efficiency direct bolt on available in satin black, gloss bla...(choose a part on the right to read more)
$1,082.40
Make a selection FVD123001 If you are experiencing over boost, odds are your wastegate diaphragm is torn or leaking. We are finding more and more failures on these diaphragms with our classics. We strongly recommend replacing them with the addition of an upgraded boost spring, part # FVD123110 . We also recommend replacing the pressure switch, part # 93060610100 high quality, German made, turbocharger wastegate diaphragm membrane. Sold individually. 1 necessary per car.
$133.10
Make a selection EIP002N35S Endless ewig n35s racing rear brake pads Porsche 964 turbo 91-92 General Fitment911 1989-94
$526.50
Make a selection FVD123013ATK K-16/24 turbo (up to 555 hp) power is focused on low and mid range rpm's. Facts: larger compressor wheel with extended tip. 47.5mm inducer diameter. Cnc modified compressor housing modified and improved back plane uprated staggered gap turbine uprated thrust bearing modified wheel to reduce backpressure balancing of all components factory vacuum unit new bearings and seals all parts are reconditioned and balanced FVD brombachers 993 k-16/24 remanufactured turbos are created for those who are looking for power that is focused in the low and mid rpm range. They are completely bolt on and do not require custom headers or special modifications. The remanufacturing process starts with re-profiling the OEM turbochar...(choose a part on the right to read more)
$2,976.60
Make a selection FVD123025ATK K24/26 exchange turbo (only OEM k24 exchange accepted) (up to 700 hp) power is focused on mid and top range rpm's. Facts: - modified compressor housing and backing plate - modified & lightened high flow compressor wheels. - remanufactured by kkk / borg warner certified technicians - free software update for those already running FVD software. FVD brombachers 996 k24/26 race turbos are new units created for those who are looking for ultimate in performance. Power is focused in the mid and top rpm range while keeping turbo lag low. They are completely bolt on and do not require custom headers or special modifications. The factory OEM turbocharger compressor housing is re-profiled and the compressor backing plate...(choose a part on the right to read more)
$2,976.60
Make a selection FVD123002ATK This is a factory series borg warner / kkk k27 turbocharger. It is a direct replacement for part # 930 123 003 01 which is currently no longer available from the factory. Send us your turbocharger and we will have it remanufactured by an OEM supplier with exacting standards in Germany. Features: restore factory performance direct replacement please note: kindly contact us for further details on where to send the turbocharger.
$3,285.88
Make a selection FSPOR992TVLV Treat your 992 turbo to the finest cat-back exhaust solution on the market. This valveed exhaust system is plug-and-play with the factory pse system so you can turn pse off for quiet highway cruising and turn pse on for ripping twin turbo sports car sound!Â
$5,245.95
Make a selection FVD123042ATK FVD Brombacher997.1 tt "700 series" upgraded turbos facts: - cnc re-profiled compressor housing and backing plate - new, lightened and larger compressor wheel (12 blades) - reworked turbine wheel, lightened and optimized for higher flow and reduced backpressure. - all new bearings. - all new piston rings and seals. - all parts cleaned, inspected and measured to motorsport specifications. - all parts are balanced (static & dynamic) up to 120.000 rpm with balancing protocol. - 47.55 mm inducer - 66 mm exducer - flow rate = 37 lbs. / minute or 280g/s - remanufactured by borg warner certified technicians - shaft tolerances are strictly maintained to ensure durability - free software update for those already runn...(choose a part on the right to read more)
$2,854.50
Make a selection FVD123020ATK Our k24 sport turbocharger is based off the optional k24 turbochargers, found in the GT2 or 993 turbo x50 models. They are remanufactured by borg warner certified technicians in Germany and are a cost-effective solution. The remanufacturing process includes full inspection of the turbocharger to ensure proper operation after the remanufacturing process. We then disassemble, clean and degrease the unit. The compressor wheels are exchanged, lightened and modified for more air flow. All clearances / shaft tolerances are checked for precision to ensure reliability. The end result is 20-30 additional horsepower, in the low and mid rpm range over the factory turbo. The sport turbo also has less lag than a factory k24...(choose a part on the right to read more)
$2,042.70
Make a selection FVD123048 FVD Brombacher997.2 tt "700 series" upgraded turbos facts: - modified compressor housing for the 3.8 l displacement - modified & lightened billet compressor wheel with 12 blades - 49.55 mm inducer - 68 mm exducer - remanufactured by borg warner certified technicians - shaft tolerances are strictly maintained to ensure durability - free software update for those already running FVD software we start by re-profiling the OEM vtg turbocharger compressor housing and modifying the compressor backing plate. This is done to replace the factory compressor wheel with a larger 12 blade, modified compressor wheel. The larger wheel is also lightened allows the turbo to flow a larger volume of air (more power), and aids i...(choose a part on the right to read more)
$6,413.00
Make a selection FVD123014ATK K-16/24 turbo (up to 555hp) power is focused on low and mid range rpm's. Facts: larger compressor wheel with extended tip. 47.5mm inducer diameter. Cnc modified compressor housing modified and improved back plane uprated staggered gap turbine uprated thrust bearing modified wheel to reduce backpressure balancing of all components factory vacuum unit new bearings and seals all parts are reconditioned and balanced FVD brombachers 993 k-16/24 remanufactured turbos are created for those who are looking for power that is focused in the low and mid rpm range. They are completely bolt on and do not require custom headers or special modifications. The remanufacturing process starts with re-profiling the OEM turbocharg...(choose a part on the right to read more)
$2,976.60
Make a selection FVD50599102MM The moshammer evo 2 front chin spoiler blends a bit of Porsche heritage into its design with canard style winglets. This effective design transforms turbulent air into a more laminar flow, creating added downforce. Porsche active aerodynamics remains fully functional in all 3 positions and the evo 2 chin spoiler secures seamlessly into the factory locations. The evo 2 spoiler's design offers a more aggressive look but also blends perfectly with other design elements like the side skirts and rear spoiler. This is an ideal addition for a leased vehicle or for those looking to return the car to its original appearance in the future. When added to other elements of either the evo rs (991.2 turbo/s) or downforce rs...(choose a part on the right to read more)
$1,386.00
Make a selection FVD51299102MM The moshammer vented rear diffuser with fins is an aggressive design that reduces aerodynamic drag. This vented diffuser allows air that is trapped by the rear bumper to exit, allowing for greater top end performance. The design also incorporates 5 fins that improve laminar airflow by reducing turbulence. Moshammer manufactured this as a direct replacement, so it secures seamlessly to the factory locations with the original hardware. This is an ideal addition for a leased vehicle or for those looking to return the car to its original appearance in the future. When added to other elements of the downforce rs (991.1 turbo/s) package, the result is a confident, cohesive stance with balanced downforce. Features: ve...(choose a part on the right to read more)
$1,460.80
Make a selection FVD512991TT01 The moshammer rear wing spoiler lip is a bold, aggressive design that maximizes downforce. The rear spoiler lip installs seamlessly without drilling and the Porsche active rear spoiler remains fully functional. This is the perfect addition for a leased vehicle or for those looking to return the car to its original appearance in the future. When added to other elements of either the evo rs (991.2 turbo/s) or downforce rs (991.1 turbo/s) packages, the result is a confident, cohesive stance with balanced downforce. Features: aggressive design increased rear downforce improved handling simple to install and remove lightweight composite material designed and manufactured in Germany FVD Brombacherhas a tradition of ...(choose a part on the right to read more)
$1,383.80
Make a selection FVD95761890MG Factory: engine - v8 twin-turbo capacity - 4806ccm compression ratio - 10,5:1 max. Power - 368kw (500hp) @ 6000rpm max. Torque - 700nm (516 lbf ft) @ 2250-4500rpm max. Speed - 275km/h max. Rpm - 6500rpm acceleration 0-100km/h - 5.1s tuning:* max. Power - 397kw (540hp) @ 6000rpm max. Torque - 780nm (575 lbf ft) @ 3500rpm max. Speed - 280km/h max. Rpm - 6700rpm acceleration 0-100km/h - 5.0s * only with sport exhaust system and sport air filter for 27 + years, FVD-Brombacherhas been setting the standard for Porsche engine building and tuning in Germany. Our deep understanding of the flat 6 Porsche engine naturally led to our engine management software. Over the years we have perfected the art of software tuning, ...(choose a part on the right to read more)
$1,094.50
Make a selection FVD95861880MG Genuine: engine - v8 capacity - 4806 ccm compression ratio - 12,5:1 max. Power - 309kw (420hp) @ 6500rpm max. Torque - 500nm @ 3500rpm max. Speed - 256km/h max. Rpm - 7000rpm acceleration 0-100km/h - 6,0s tuning: max. Power - 325kw (442hp) @ 6000rpm max. Torque - 530nm @ 4500rpm max. Speed - 265km/h max. Rpm - 7200rpm acceleration 0-100km/h - 5,7s for 27 + years, FVD-Brombacherhas been setting the standard for Porsche engine building and tuning in Germany. Our deep understanding of the flat 6 Porsche engine naturally led to our engine management software. Over the years we have perfected the art of software tuning, making substantial gains in horsepower and torque, while retaining drivability and most importan...(choose a part on the right to read more)
$1,484.16
Make a selection FVD98010002 Kit includes: 2 x sport motronic dme (ecu) exchange 2 x sport airfilter 1 x sport exhaust system genuine: engine - v10 cylinder capacity - 5733ccm compression ratio - 12,0:1 max. Power - 450kw (612hp) @ 8000rpm max. Torque - 590nm @ 5750rpm max. Speed - 330km/h max. Rpm - 8400rpm acceleration 0-100km/h - 3.9s tuning: max. Power - 496kw (675hp) @ 8000rpm max. Torque - 670nm (495 lbf ft) @ 6000rpm max. Speed - 345km/h max. Rpm - 8600rpm acceleration 0-100km/h - 3.7s FVD dme / ecu programming philosophy: for 27 + years, FVD-Brombacherhas been setting the standard for Porsche engine building and tuning in Germany. Our deep understanding of the flat 6 Porsche engine naturally led to our engine management software. ...(choose a part on the right to read more)
$17,032.10
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |