Vehicles
Sections
245 not categorized PORSCHE 924S MENS RINGCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 911 1989-94 (includes uncategorized and accessory items) 91161212202 Brand new part for the early steering column harness end or the engine compartment relay board. easily installed comes complete with the top the bottom and the solder in pins. View/Change Diagram
$49.95
Make a selection 91154240403 This seal sits inside the door frame along the a-pillar and roof. It prevents moisture and wind noise from entering the cabin. As these classics age the original gasket becomes brittle and will crack, so it is essential that this seal is in good order. Sold individually. Passenger's side fitment. 1 necessary per car. View/Change Diagram
From $44.33
Make a selection 91110190160EQ Oem (original equipment manufacturer) complete set of bearings (including # 8) sourced in Germany to ensure quality, reliability and precise fitment. Set includes: 1 qty. Crankshaft main bushing sleeve - bushing viii - oversize +0.25mm 12 qty. Crankshaft main bearing shells ii-vii (half) - oversize +0.25mm 2 qty. Crankshaft main bearing shells i (half) - oversize +0.25mm sold as a set. 1 necessary per car. Please note: please check the model fitment tab to ensure accurate fitment.
$692.05
Make a selection 91153170202 As a striker plate ages, it will start to rattle and can potentially be a safety risk. We recommend securing them with new oval head screws, part # 99921900800. 2 screws are needed per plate. We also recommend adding new striker plates gaskets, either 90153170323 or 90153170324 depending on what thickness you need. This line is a high-quality replacement part, sourced in Germany and designed to perform like the original. Sold individually. 1 necessary per car.
From $133.10
Make a selection 98655297418KT Enhance the race-inspired design of your Boxster or Boxster s with our aluminum-look paint trim. Complete interior kits includes instrument surround, center air vents, side vents, door trim covers, steering wheel, handbrake lever; kits are very complete. Simple installation. Must specify color code or interior leather for exact match and seamless matching interior. Add $255.00 for any color except black. Tiptronic add an additional $90.00. Separate pieces can be special ordered, call for individual pieces.
$4,054.17
Make a selection 477412031B Sach/boge suspension components have been standard equipment on Porsche for years. Buy with the knowledge that the factory uses sachs/boge parts and stands behind their quality and precision that they bring to everything the manufacture. Sachs/boge shocks and struts provide a taut, sporty ride while remaining a comfortable street ride.
$103.00
Make a selection 901602702AXATK The cdi or hkz as it is known in Germany, is the high-voltage condenser ignition control unit. Aging cdi / hkz units lead to deterioration of performance with time. A failing unit's symptoms include a fluctuating tach, stalling, loss of power to the ignition coil and no start situations, leaving you stranded. Send us your original cdi / hkz and German technicians with many years of experience will completely remanufacture it to new specifications. This is not a repaired unit like many of our competition offer, this is a completely remanufactured unit using new upgraded components. The remanufacturing process includes: disassembly inspection and cleaning complete diagnosis (including oscillogram) on a test benc...(choose a part on the right to read more)
$768.90
Make a selection 91153170102 As a striker plate ages, it will start to rattle and can potentially be a safety risk. We recommend securing them with new oval head screws, part # 99921900800. 2 screws are needed per plate. We also recommend adding new striker plates gaskets, either 90153170323 or 90153170324 depending on what thickness you need. This line is a high-quality replacement part, sourced in Germany and designed to perform like the original. Sold individually. 1 necessary per car.
From $82.50
Make a selection 93034702502 If you are experiencing clunking or popping sounds and difficulty turning the steering wheel, then inspect your steering intermediate shaft universal joints right away. Genuine part sourced from Porsche ag in Germany to ensure quality, reliability and precise fitment. Sold individually. 2 necessary per car.
$342.10
Make a selection 91511608705 On the flywheel side, the guide tube facilitates the movement of the thrust bearing in order to engage / disengage the clutch. On the gearbox side it provides a seal between the gearbox and driveshaft. These two functions are critical, so we recommend replacing the guide tube with any thrust bearing or clutch replacement. High-quality OEM (original equipment manufacturer) replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 1 necessary per car.
From $115.01
Make a selection 91163193900EQ If you are restoring or replacing a rear taillight, you may want to consider this. It is a lightweight, high-quality OEM replacement, designed to perform like the original. Perfect for a race application, or for a lightweight street car. Quality replacement part manufactured by dansk. They offer a complete line of replacement parts to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. This commitment has made dansk one of the original equipment suppliers to the Porsche in Germany. Sold individually. Driver's side fitment. 1 necessary per car.
$320.10
Make a selection 93010090803EQ High-quality victor reinz replacement gaskets, o-rings and washers to reseal your cylinder heads. Victor reinz has been supplying German auto manufacturers and Porsche for decades. They are a trusted name in gaskets and sealing products. This kit is complete with everything needed and we source this directly in Germany for an added level of quality. Sold individually. 1 set necessary per car. To complete the gasket set for the entire engine, also order part # 93010090104eq
$625.90
Make a selection 915302911161 This ring and pinion is manufactured in Germany to our specifications using case hardened steel (18crnimo7-6). Our specifications include special heat treatment which is extremely wear resistant, contains a tough inner core, includes high tensile strength and exhibits lower noise levels. Sold as a set. 1 necessary per car. Technical info: setting for the drive train is on the bevel gear and not as usual on the ring gear.
$5,408.70
Make a selection 93010540906 A liquid sodium filled valve transfers heat away from the head towards the valve guide in order to reduce combustion chamber temperatures. This is the valve of choice when rebuilding motors. When working on your cylinder head, we recommend replacing the valves, valve seat rings, guides, springs, retainers and temperature sensor at the same time to reduce future labor costs. Sold individually. 6 necessary per car.
$37.40
Make a selection 93010432100 As valve guides age, they lose their ability to locate the valve to the valve seat. That can create a loss of performance due to the ineffective seal of the combustion chamber. Be sure to replace your guides when replacing valves, valve springs, etc. High-quality OEM replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 6 necessary per vehicle.
From $14.30
Make a selection 93010501304 Genuine intermediate shaft and gear, sourced in Germany to ensure quality, reliability and precise fitment. We recommend ordering 6 qty. Oil pump lock plates part # 99903900100 for installation. Please note: please check the model fitment tab to ensure accurate fitment. Sold individually. 1 necessary per car.
From $1,612.60
Make a selection 93010541951EQ When working on your cylinder head, we recommend replacing the valves, valve seat rings, guides, springs, retainers and temperature sensor at the same time to reduce future labor costs. Quality German aftermarket replacement designed to perform like the original. Sold individually. 6 necessary per car.
$49.50
Make a selection 93010734714 This part is sourced in Germany to ensure quality, reliability and precise fitment. This will fit all the vehicles listed in the fitment tab and those that have been updated to pressure fed tensioners. This line requires that you also purchase part # 93010734706 . We also recommend purchasing 1 qty. Union nut, part # 90010400303 and 1 qty. Cutting ring sleeve, part # n0208251 for installation. Also need the right side? Please order part # 93010734812 for the 911 3.2 l and 930 3.3l. Order part # 93010734815 for the 965 3.3 l. Sold individually. 1 necessary per car.
From $41.80
Make a selection 93060291901 Replacing your distributor cap at regular intervals is highly recommended. The cap is susceptible to carbon deposits and can also develop hair line cracks due to heat and vibration. Those cracks allow moisture and debris in which hampers ignition and can erode terminals. We recommend closely examining both caps prior to ordering and replacing both if necessary. It is also a good idea to change the rotors at the same time, part # 93060290202 and the dust covers 93060290900. Sold individually. View/Change Diagram
From $124.00
Make a selection 96410541903 When working on your cylinder head, we recommend replacing the valves, valve seat rings, guides, springs, retainers and temperature sensor at the same time to reduce future labor costs. Oem, German sourced exhaust valve for the 964 c2 / c4 and rs that have the m64.01/02/03 motors. Sold individually. 6 necessary per car. View/Change Diagram
From $25.50
Make a selection 930123002X This remanufactured turbo is a direct replacement for original part # 930 123 002 00. The remanufacturing is completed in Germany by kkk/borg warner certified technicians. This ensures reliability, superior performance and cost effectiveness. The remanufacturing process includes: complete disassembly. All parts are cleaned, inspected and measured for tolerances. Turbine wheels are replaced. Thrust bearings are replaced. All new seals are installed. Internals are reconditioned. Parts are balanced (static & dynamic) according to balancing protocol. For a complete installation we recommend adding a gasket, part # 93012319105 an intake sleeve, part # 93011015801 and be sure to have a few spare studs on hand, part #...(choose a part on the right to read more)
From $2,981.74
Make a selection 93011115701EQ This cross over connector replaces original part # 930 111 157 01, it is a quality coated steel replacement part manufactured by dansk. They offer a complete line of replacement parts to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. This commitment has made dansk one of the original equipment suppliers to the Porsche in Germany. For proper installation, we recommend a new exhaust gasket, part # 93011119307 and sealing ring, part # 91111118903 sold individually. 1 necessary per car.
$58.30
Make a selection 96411602853 Higher transmittable torque. Higher clamping load. Less abrasion. Direct replacement for the oe pressure plate. 240 mm. Max torque: 486 lb/ft (660 nm) weighs: 9.5 lbs. (4.3 kg) the reinforced sachs performance pressure plate (clutch cover) has fundamental advantages against an oe pressure plate, such as a higher transmittable torque and higher resistance against thrust. It also allows for faster and sportier gearshifts. That makes it extremely useful for street tuning, endurance races and hill climbing. The sachs performance clutches are assembled by hand. This guarantees the highest quality attributes in clamping load and release characteristics. Installation notes for those with single mass flywheel kits: whe...(choose a part on the right to read more) View/Change Diagram
From $634.70
Make a selection 95030431130 This is the rs model g50.10 transmission synchronizer ring for 1st - 2nd gear. Original quality, sourced in Germany and made of steel for motorsports applications. Weighs: 0.12 lbs. (.05 kg) sold individually. Please note: be sure to check the model fitment tab to ensure correct fitment.
From $282.27
Make a selection 95011681306 This guide tube works in conjunction with a 32 mm release (throw-out) bearing. Exact dimensions: id 27.1mm od 31.9mm length 49mm weight: .286 lbs. (.13 kg) View/Change Diagram
From $57.51
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |