PORSCHE 356C ETUCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 911 1994-98 - Front Axle/Steering (includes uncategorized and accessory items) RES99709064SRSR This is a custom system made for a 997.1 GT3 cup with a 4.0 l conversion that has 500 hp+ - header diameter 55mm - tube diameter 76mm after the headers - recommended for engines 500 hp+ all motorsport and racing parts are special order items. Special order items must be paid for in advance. Special order items are sold on a non-cancelable, non-exchangeable, non-returnable, non-refundable basis and do not carry any warranty. No exceptions.
$5,846.50
Make a selection S745012 Rennline adjustable control arm links solve both these problems. Manufactured from 6061 aluminum and feature a turnbuckle design that allows each arm to be lengthened or shortened as needed to restore proper suspension geometry on a lowered Porsche. The fk teflon-lined rod end bearings ensure precision handling and lock in your car's alignment settings, ensuring predictable cornering under all conditions. Unlike the competitors' product, rennline arms come with eccentric locks and new hardware so you can completely eliminate the factory setup, which is known to go out of adjustment under hard driving and ruin your car's alignment. Sold each, two needed per car. General Fitment911 1994-98
$306.90
Make a selection S727374101 If you're serious about how your 993 handles, you should upgrade the rear suspension with adjustable control arm links. There are two major drawbacks to the factory links: 1) you can't lower your car and maintain proper suspension geometry. The factory links create too much toe-in, which cannot be adjusted out, creating handling problems and excessive tire wear. 2) the factory links have rubber bushings, which make handling imprecise, especially in performance driving when suspension loads are highest. General Fitment911 1994-98
$1,758.90
Make a selection RES99605200S This muffler replaces the OEM catalytic converters and the OEM side mufflers. Weighs 24.2 lbs (11kg) ecu software is nessesary with 100 cell cats increase power up to 34 hp (26kw (35 hp) and 16 lb. Ft (21nm) with software. Includes adjustable tips that can be turned down for track use. Also available with 200 cell cats. All motorsport and racing parts are special order items. Special order items must be paid for in advance. Special order items are sold on a non-cancelable, non-exchangeable, non-returnable, non-refundable basis and do not carry any warranty. No exceptions.
$3,070.10
Make a selection RES99620010S Complete race exhaust system for 996 Carrera - up to 26kw (35 hp) more power - no side muffler - weight reduction - complete system weight only 36lbs (16.5 kg) dme programming necessary. All motorsport and racing parts are special order items. Special order items must be paid for in advance. Special order items are sold on a non-cancelable, non-exchangeable, non-returnable, non-refundable basis and do not carry any warranty. No exceptions.
$4,492.40
Make a selection RES99615260SS This muffler replaced the complete exhaust system after the headers. Fits cup headers. Also available with 200 cell cats for GT3 cup cars (res 996 152 60sc). No dme upgrade nessesery. Increase power up to 26kw (35ps) and 21nm all motorsport and racing parts are special order items. Special order items must be paid for in advance. Special order items are sold on a non-cancelable, non-exchangeable, non-returnable, non-refundable basis and do not carry any warranty. No exceptions.
From $2,997.84
Make a selection FVD123013ATK K-16/24 turbo (up to 555 hp) power is focused on low and mid range rpm's. Facts: larger compressor wheel with extended tip. 47.5mm inducer diameter. Cnc modified compressor housing modified and improved back plane uprated staggered gap turbine uprated thrust bearing modified wheel to reduce backpressure balancing of all components factory vacuum unit new bearings and seals all parts are reconditioned and balanced FVD brombachers 993 k-16/24 remanufactured turbos are created for those who are looking for power that is focused in the low and mid rpm range. They are completely bolt on and do not require custom headers or special modifications. The remanufacturing process starts with re-profiling the OEM turbochar...(choose a part on the right to read more)
$2,976.60
Make a selection RES99620060S Race exhaust system 996 GT3, stainless steel, cat bypass with tips facts: - + 25 crank hp & + 19 crank torque - catalytic bypass - includes quick release clamps - made in Germany - dme programming necessary. All motorsport and racing parts are special order items. Special order items must be paid for in advance. Special order items are sold on a non-cancelable, non-exchangeable, non-returnable, non-refundable basis and do not carry any warranty. No exceptions.
From $4,240.50
Make a selection RES98605000S - + 11 crank hp & + 10 crank torque. - weighs 23 lbs. (10,5 kg). - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - minimal drone for a race system. - designed to work with OEM or aftermarket headers that fit like oem. - dual 2 3/4 (70mm) round tips. - includes sleeves and mounting plates. - made in Germany. - intoxicating growl at idle, partial throttle and wide open throttle. - ecu programming is not necessary. - for manual and pdk transmissions. FVD is proud to introduce our newest line of Brombacherexhaust systems. Brombacher exhausts are engineered for the discerning Porsche owner and offer unmatched performance, unparalleled quality, and incredible value. All of our exhausts a...(choose a part on the right to read more)
$2,643.30
Make a selection RES98005000T The titanium version of the FVD sport muffler gives the carr. Gt (980) a true formula one like scream! This exhaust is much less restrictive than the factory which produces more power and a great sound! + 25 crank hp & + 19 crank torque. Weighs 27 lbs. (12,3 kg). 2 3/4 tubing (70mm) straight through design for max. Power. Includes quick release clamps. Dme programming necessary. Made of 1,000 degree+ celsius titanium. Reuses factory tips. Made in Germany. All motorsport and racing parts are special order items. Special order items must be paid for in advance. Special order items are sold on a non-cancelable, non-exchangeable, non-returnable, non-refundable basis and do not carry any warranty. No exceptions.
$13,277.00
Make a selection RES99605100S This muffler replaces the OEM catalytic converters and the OEM side mufflers. Weighs 24.2 lbs (11kg) ecu software is nessesary with 100 cell cats increase power up to 34 hp (26kw (35 hp) and 16 lb. Ft (21nm) with software. Includes adjustable tips that can be turned down for track use. Also available with 200 cell cats. All motorsport and racing parts are special order items. Special order items must be paid for in advance. Special order items are sold on a non-cancelable, non-exchangeable, non-returnable, non-refundable basis and do not carry any warranty. No exceptions.
$2,658.70
Make a selection FVD123014ATK K-16/24 turbo (up to 555hp) power is focused on low and mid range rpm's. Facts: larger compressor wheel with extended tip. 47.5mm inducer diameter. Cnc modified compressor housing modified and improved back plane uprated staggered gap turbine uprated thrust bearing modified wheel to reduce backpressure balancing of all components factory vacuum unit new bearings and seals all parts are reconditioned and balanced FVD brombachers 993 k-16/24 remanufactured turbos are created for those who are looking for power that is focused in the low and mid rpm range. They are completely bolt on and do not require custom headers or special modifications. The remanufacturing process starts with re-profiling the OEM turbocharg...(choose a part on the right to read more)
$2,976.60
Make a selection FVD34101802ATK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will properly install our FVD clubsport front control arm bushings, part # FVD341999r. They are made with 85 shore rubber (like the rennsport model). Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrangements can ...(choose a part on the right to read more)
$418.00
Make a selection FVD58099100 German manufactured bolt in harness bar solution that is less obtrusive than a full roll bar. This harness bar is secured to the rear strut towers with the included high-grade fasteners. Features: seamlessly secured to the rear strut towers allows full front seat range of motion ideal for a lease or to return to the original equipment does not require trimming or cutting any interior parts discreet single belt tube airbag and belt tensioner system remain fully operational chromoly steel tig welded black finish factory seat belts or 4-5-6-point belts can be used. Cost effective for club sport use. Please note: this requires the removal of the rear seat back rests.
$764.50
Make a selection FVD20798700 This FVD motorsports oil pump kit is a must for 987.1 Caymans and Boxsters driven on the track. Our kit includes a second return oil pump and our FVD motorsports oil pan. The issue: the 987.1 Boxster/Cayman from 2005 to 2008 has the factory return oil pump located on the right rear side. On the left side, the return oil pump located in front. So when driven fast in right turns, the oil from the camshaft case (rear left) does not flow back quickly enough into the oil pan. When the oil pan is starved of oil, the oil pump sucks in air and over time the motor will seize. The solution: our tandem return oil pump draws oil from the camshaft housing in (rear left, 3rd cylinder) and feeds it back into the oil pan so th...(choose a part on the right to read more)
$3,274.30
Make a selection FVD20792400 Der aluminiumkuhler ist in schichtbauweise gefertigt und sorgt mit innenliegenden wirbelblechen fur optimale warmeabstrahlung. Olkuhler dieser bauart sind standard fur getunte motoren bis hin zur formel 1. 16 reihen, lange 330mm, anschlussabstand 250mm, netzbreite 290mm, befestigungslocherabstand 310mm, hohe 140mm.
$478.79
Make a selection FVD33150040 Replace worn-out original rear sub frame (side panel) bushings and return your car to its original ride quality with this cost effective alternative. This bushing is made in Germany. It is crafted in high carbon steel and 7075 t6 aircraft aluminum and includes a 65 shore hardness value core. This is a front and rear bushing for one sub frame. 2 are necessary per car. If you are looking for a sportier upgrade we suggest our clubsport sub frame bushing set, part # FVD33150040r. We also sell complete sub frames with the bushings installed, part # FVD331993001.
$418.00
Make a selection FVD50599108MM The moshammer stormforce evo rs front chin spoiler for the GTS model blends a bit of Porsche heritage into its design with canard style winglets. This effective design transforms turbulent air into a more laminar flow, creating added downforce and uplift reduction. It also incorporates twin air guides to assist with brake ventilation and underbody air flow efficiency. The moshammer stormforce evo rs front chin spoiler design offers exclusive aesthetics, aero functionality and it is secured seamlessly into the factory locations without modification. This is an ideal addition for a leased vehicle or for those looking to return the car to its original appearance in the future. When added to other elements of the s...(choose a part on the right to read more)
$1,230.90
Make a selection FVD51299102MM The moshammer vented rear diffuser with fins is an aggressive design that reduces aerodynamic drag. This vented diffuser allows air that is trapped by the rear bumper to exit, allowing for greater top end performance. The design also incorporates 5 fins that improve laminar airflow by reducing turbulence. Moshammer manufactured this as a direct replacement, so it secures seamlessly to the factory locations with the original hardware. This is an ideal addition for a leased vehicle or for those looking to return the car to its original appearance in the future. When added to other elements of the downforce rs (991.1 turbo/s) package, the result is a confident, cohesive stance with balanced downforce. Features: ve...(choose a part on the right to read more)
$1,460.80
Make a selection FVD50599109MM The moshammer stormforce evo rs front chin spoiler for the c2 / c2s / c4 / c4s and the t models blends a bit of Porsche heritage into its design with canard style winglets. This effective design transforms turbulent air into a more laminar flow, creating added downforce and uplift reduction. It also incorporates twin air guides to assist with brake ventilation and underbody air flow efficiency. The moshammer stormforce evo rs front chin spoiler design offers exclusive aesthetics, aero functionality and it is secured seamlessly into the factory locations without modification. This is an ideal addition for a leased vehicle or for those looking to return the car to its original appearance in the future. When added...(choose a part on the right to read more)
$1,237.50
Make a selection FVD512991TT01 The moshammer rear wing spoiler lip is a bold, aggressive design that maximizes downforce. The rear spoiler lip installs seamlessly without drilling and the Porsche active rear spoiler remains fully functional. This is the perfect addition for a leased vehicle or for those looking to return the car to its original appearance in the future. When added to other elements of either the evo rs (991.2 turbo/s) or downforce rs (991.1 turbo/s) packages, the result is a confident, cohesive stance with balanced downforce. Features: aggressive design increased rear downforce improved handling simple to install and remove lightweight composite material designed and manufactured in Germany FVD Brombacherhas a tradition of ...(choose a part on the right to read more)
$1,383.80
Make a selection JRZRSR993 We are an authorized reseller and installer of jrz suspension. As racing enthusiasts ourselves, we know that the best suspension for street or for track is by jrz. With years of engineering, race testing, and winning, jrz provide the driver with the best possible handling vehicle for their driving needs. General Fitment911 1994-98
$7,155.00
Make a selection 96433102200RATK Unsure about installing a replacement bushing? Send us your trailing arm and we will properly recondition and install the bushing for you. The reconditioning process includes full inspection of your trailing arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we properly install our rear clubsport trailing arm bushings, part # FVD3310212291. Our rear trailing arm bushings contain rubber inserts with a shore hardness value of 85, like what is used on rennsport models. They offer rs style handling characteristics, superior durability and are still forgiving enough for street use. When reconditioning the trailing arms, we als...(choose a part on the right to read more)
$672.10
Make a selection FVD34101702RAT We will send you a reconditioned control arm, kindly send back your old part, or core . The reconditioned control arm has been full inspected, disassembled, degreased and we have properly installed FVD race front control arm bushings. They are made with uniball bearings so suspension motion is accurately repeated in every corner. Please note: each control arm is remanufactured in Germany, so the lead times can vary. This part is sold on an exchange basis, as such an additional charge (a core deposit) will be added to the purchase price of the part. After receiving your new part, kindly send back your old part, or core . Once the core is returned to us and it has been inspected to ensure it is rebuild-able and r...(choose a part on the right to read more)
$440.00
Make a selection RES96400100S1 More low and mid-range torque than our race system with cat bypass. Larger primaries, larger collector, largest diameter tubing on the market. Made for mid-range and top end performance with the added beauty of dual exhaust tips! + 25 hp & + 23 torque - 100 cell hjs tri-metallic race catalytics. -2 1/2 tubing (63.5mm) for max. Power across the rpm range.* -weighs 49 lbs. (22 kg). -German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - aeroquip cone style catalytic connection design to prevent exhaust leaks. -includes aeroquip quick release clamps. -made in Germany by m&m exhaust, gmbh. -dual round 3 exhaust tips -intoxicating flat 6 growl at idle, partial throttle and wide open throttle. P...(choose a part on the right to read more)
$7,772.60
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |