Vehicles
Sections
131 not categorized PORSCHE 944 ENGINE PARTSCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 911 1994-98 (includes uncategorized and accessory items) 91121152200 Engine compartment blower to rt. Heat exchanger; 60mm x 1100 mm. Not for ca models; original tan paper/aluminum
$20.09
Make a selection 911606105HXATK The cis injection / k-jetronic warm up regulator is a critical component that performs the following functions: lowers pressure when engine is cold. Absorbs / distributes engine heat. Allows for an additional rich mixture under full load to prevent engine damage. Altitude correction. Send us your original part and we will have it remanufactured for you. We do not offer a core exchange on this part. Each part is remanufactured in Germany, so the lead times can vary. Sold individually. 1 necessary per car.
$744.70
Make a selection 9018DA Wossner are the innovative specialists for high performance pistons and connecting rods. Their products can be found in engines operating at the highest levels of motorsport, in competition and, of course, in everyday use. In fact, anywhere where longevity and operational noise are important factors. Wossner products are the source of superior power behind the success of well known motorsport teams at national and international race meets. General Fitment911 1994-98
$1,205.28
Make a selection 93010090104EQ High-quality victor reinz replacement gaskets, o-rings and washers to reseal your engine case (short block). Victor reinz has been supplying German auto manufacturers and Porsche for decades. They are a trusted name in gaskets and sealing products. This kit is complete with everything needed and we source this directly in Germany for an added level of quality. Sold individually. 1 set necessary per car. Please note: if you prefer the genuine crankshaft sealing ring, please order part # 99911342641 this also includes the intermediate shaft o-ring, part # 99970731540. Please check the model fitment tab to ensure accurate fitment.
$118.80
Make a selection 99763220100 Known as: luggage compartment lamp / light / light luggage compartment front and rear / light luggage compartment front / light engine compartment luggage compartment View/Change Diagram
From $8.60
Make a selection 96410090200EQ FVD cylinder head gasket sets contain high quality German sourced gaskets, seals and o-rings. This kit contains a complete set of gaskets to make a teardown / rebuild more convenient. Sold as a complete set. 1 necessary per car. To complete the gasket set for the whole engine please order part # 93010090104eq
$387.20
Make a selection 96410524609ST This fits 964 c2 / c4 and rs models with engine codes # m64.01/02/03. This is an OEM part, sourced directly from Germany. Professional installation is required. Different manufacturing tolerances require an inspection of the free clearance of all parts! If you're not sure about what parts are right for your build, be sure to ask one of our parts specialists. Sold individually. 1 necessary per car.
$1,441.00
Make a selection 96437504381 Replace your worn-out, original soft rubber engine mounts with our higher density, rs specification rubber bushing. This is manufactured of rubber with a 75-shore hardness value. 75-shore is the same density as what is used in the rs models. It is more durable, provides more positive, sharper shifts and offers crisper throttle response. Yet, rs spec rubber is still quiet and comfortable for street use. Features: sharper shifts crisper throttle response does not produce nvh (noise vibration harshness) like teflon or solid bushings rubber has a shore hardness value of 75 (like rs models) made in Germany this mount is a high-quality OEM (original equipment manufacturer) replacement part, designed to perform like t...(choose a part on the right to read more)
From $199.99
Make a selection 96410601402EQ This OEM cover sits low nearest the rear bumper. If you are removing the motor for maintenance, be sure to check and replace the engine covers / heat shields as necessary. We recommend purchasing a new seal, part # 96410622301 and plug, part # 96410623701 to complete the installation. Sold individually. 1 necessary per car.
$601.70
Make a selection 96437504381UNI The rs model engine mount is not a hydro-elastic mount like most models. It contains a rubber core with an 85-shore hardness value. That equates to a more responsive chassis and improved shifting response. A perfect compromise for street and track use as it is more forgiving than aftermarket solid mounts. Sold individually. 2 necessary per car. To install these mounts on any model 964 / 965 / 993 and 993 tt, we recommend our rs engine mount set that includes 2 mounts and all the mounting hardware, part # FVD375964
$218.90
Make a selection 99310090236EQ FVD cylinder head gasket sets contain high quality German sourced gaskets, seals and o-rings. This kit contains a complete set of gaskets to make a teardown / rebuild more convenient. Sold as a complete set. 1 necessary per car. To complete the gasket set for the whole engine also order part # 93010090104eq
$614.58
Make a selection 99310511607 Replacement lower valve cover, perfect for a restoration or an engine refresh. We recommend installing 2 new gaskets, part # 99310513502 and 11 valve cover combination screws per side, part # 90006723801. Sold individually. 2 necessary per vehicle. Left or right side fitment View/Change Diagram
From $118.84
Make a selection 99311691101 Eliminate your clutches slipping and chattering with this genuine kit. We only recommend this kit for non-modified cars that are not running any aftermarket upgrades like exhaust, chip tuning or larger displacements, etc. Complete kit consists of: 1 qty. Clutch disc 1 qty. Pressure plate 1 qty. Release bearing 1 qty. Spline lubricant kit weighs 14.1 lbs. (6.4 kg) tech tip: when you are planning to install a new clutch, it is a good idea to replace the clutch release fork and shaft to ensure proper clutch engagement, our part # FVD116999. We also recommend a new guide tube 95011681306 for proper installation. View/Change Diagram
From $768.04
Make a selection 99311071250 As our classics age we are finding that we are needing to replace these plastic intake manifolds more frequently. Be sure to check yours at your next service. If you are replacing the intake manifold, we suggest purchasing the sealing rings part # 99311071301 and the rubber sleeve, part # 96411068703 please note: this fits the m64.21/22/23/24 engines. Sold individually. 6 necessary per car. View/Change Diagram
From $21.32
Make a selection 96560612601EQ Oxygen or lambda sensors are critical to your engines health. If the sensor is faulty you may experience poor gas mileage, rough idling or engine pinging. High-quality replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Be sure to check the "fits these models" tab to make sure that this will work for your needs. Sold individually. 1 necessary per car.
$111.10
Make a selection BES99102240SHD + 15 hp & + 14 torque - 200 cell high flow, tri metal German hjs "hd" high durability matrix sports catalysts. - can be used with FVD "brombacher" mufflers. - weighs 15.5 lbs. (7.0 kg). - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - made in Germany. - intoxicating growl at idle, partial throttle and wide open throttle. The catalytic converter cores used in this system are the most advanced in the industry. They are produced by hjs in Germany and are a 200 cpsi (cell per square inch) tri-metal design. Tri-metal cats are the freest flowing and environmentally friendly aftermarket cats produced today. Tri-metal catalytic converters are rodium, platinum and iridium coated and per...(choose a part on the right to read more)
$3,293.40
Make a selection 99970731540 Crankcase / intermediate shaft cover seal. Sold individually. Did you know that we have complete engine service kits and complete gasket sets to make your next service a breeze? Find them under the spare parts tab, engine, then maintenance kits or gasket sets. View/Change Diagram
From $2.10
Make a selection 99919209750EQ Belts undergo a lot of friction and wear. They are cost effective to change and will keep your alternator and engine in good condition. Be sure to follow recommended service and replacement intervals set by Porsche on belts. High-quality replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 1 necessary per car. Please note: please check the model fitment tab to ensure accurate fitment.
$9.90
Make a selection BES98115000S This is a forum favorite for the best sound with minimal drone! This muffler really does everything so well. Civilized while cruising, a beast under load and cup car gurgles and crackles off throttle. + 11 hp & + 10 tq gain. - weighs 35.4 lbs - thermal insulation on piping to keep suspension components cool. Withstands up to 2,012 degrees fahrenheit (1,100 degrees celsius). - 2 1/2 tubing (63.5 mm). - 2 x 3.5 (90 mm) round tips. - intoxicating growl at idle, partial throttle and wide open throttle. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - minimal resonance / drone in the cabin (200 rpms worth) compared to the competition's mufflers. This can be verified on the forums like ...(choose a part on the right to read more)
$3,314.30
Make a selection 9A160618101 Oxygen or lambda sensors are critical to your engine's health. If the sensor is faulty you may experience poor gas mileage, rough idling or engine pinging. Replace it with this high-quality Bosch OEM (original equipment manufacturer) replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 2 necessary per car. Please note: be sure to check the "fits these models" tab to make sure that this will work for your model / application.
From $133.10
Make a selection 99919234550EQ Belts undergo a lot of friction and wear. They are cost effective to change and will keep your alternator and engine in good condition. Be sure to follow recommended service and replacement intervals set by Porsche on belts. High-quality replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 1 necessary per car.
$14.30
Make a selection BES99102240SHDO + 15 hp & + 14 torque - 200 cell high flow, tri metal German hjs "hd" high durability matrix sports catalysts. - can be used with FVD "brombacher" mufflers. - weighs 15.5 lbs. (7.0 kg). - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - made in Germany. - intoxicating growl at idle, partial throttle and wide open throttle. The catalytic converter cores used in this system are the most advanced in the industry. They are produced by hjs in Germany and are a 200 cpsi (cell per square inch) tri-metal design. Tri-metal cats are the freest flowing and environmentally friendly aftermarket cats produced today. Tri-metal catalytic converters are rodium, platinum and iridium coated and per...(choose a part on the right to read more)
$4,383.50
Make a selection BES987C02F0S "brombacher" 987-2/s (sound version) stainless steel exhaust system
$7,420.60
Make a selection BES99125040S Perfect muffler for those looking for a more aggressive exhaust note without changing the factory catalytic converters. The added benefit is you can reuse your OEM catalytic converters for emissions purposes. + 25 hp & + 19 torque* - reuses OEM cats, perfect for those concerned about warranty. - open muffler design for added power. - weighs 19 lbs. (8,6 kg) - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - 4 on a scale of 1-10 in volume (1 being stock) below 3,000 rpms, 6 on a scale of 1-10 in volume under maximum load (3 being stock). - includes new clamps and muffler straps.* - made in Germany. - modular design for future 100 cell, 200 cell or cat bypass use. - more distinguished ...(choose a part on the right to read more)
$2,655.40
Make a selection BES99115000SKR + 11 hp & + 10 tq gain. - 2 3/4 tubing (70mm). - 18 lb. (8.5 kg)weight savings over OEM center muffler. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - absolutely no drone in the cabin. - does not interfere with emissions and will not trigger the check engine light. - ecu programming (software) is not necessary. - replaces OEM center muffler and connects to OEM header and OEM side mufflers and OEM tips. Please note: this muffler is a direct replacement the 991 Carrera s (3.8l - us model) which comes standard with valves. It is also a direct replacement for the Porsche sport exhaust option. This center muffler bypass for the 991 is one of the most technically advanced for Porsche t...(choose a part on the right to read more)
$3,713.60
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |