Vehicles
Sections
124 not categorized PORSCHE 944 TURBO WE NEED A CARCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 911 1994-98 (includes uncategorized and accessory items) FVD99661831MG Genuine: engine - 6 cylinder boxer capacity - 3600ccm compression ratio - 11,7:1 max. Power - 265kw (360hp) @ 7200rpm max. Torque - 370nm (273lbf ft) @ 5000rpm max. Speed - 302km/h max. Rpm - 7600rpm acceleration 0-100km/h - 4.8s tuning: max. Power - 276kw (375hp) @ 7000rpm max. Torque - 390nm (288lbf ft) @ 5000rpm max. Speed - 310km/h max. Rpm - 7900rpm acceleration 0-100km/h - 4.6s for 27 + years, FVD-Brombacherhas been setting the standard for Porsche engine building and tuning in Germany. Our deep understanding of the flat 6 Porsche engine naturally led to our engine management software. Over the years we have perfected the art of software tuning, making substantial gains in horsepower and torque, while re...(choose a part on the right to read more)
$1,204.50
Make a selection FVD111LAMVER Having problems with your check engine light? Want to run cat bypass pipes or a free flowing sports catalyst set up on your vehicle without having to reprogram the dme (ecu)? This adapter offsets the oxygen sensor about 1.5 inch from the gas stream. This achieves, in most cases, a sufficient measurement for the air/co ratio and increases the tolerance range between the pre and post cat oxygen sensors. In addition, the sensitivity of the oxygen sensor is also reduced allowing you to run a nearly any exhaust or catalytic set up, including bypass pipes, without the need to reprogram your ecu! Use only for the 2nd oxygen sensor (after catalytic)! General FitmentBOXSTER 1997-04911 GT3 2007-11 911 2005-08 911 GT3 2003-05 911 TURBO/GT2 2001-05 911 1998-05 911 1989-94 911 1987-89 911 1984-86 911 1978-83 CAYENNE 2007-10 CAYENNE 2003-06 CAYMAN 2006-08 BOXSTER 2005-08 968 1992-95 944 1982-85 944 1985-88 944 1989-91 928 1992-95 928 1987-91 928 1983-86 924 1986-88 924 1980-85 911 1994-98
$42.90
Make a selection 115900997BIT011 The pss 10 suspension kit provides the ultimate in performance tuning. The fully adjustable monotube gas shock absorbers offer a selection of nine precise compression and rebound settings. The front and rear progressive rate springs allow accurate adjustment of the vehicle ride height and center of gravity for the level of performance you seek. Handling and control are just a few twists away. Regardless of whether in daily motoring, on the nordschleife of the nurburgring at the weekend, in training courses or in club sports - it's all pure driving enjoyment! Product advantages at a glance: • bilstein mono-tube/inverted technology • bilstein road tested and tuned • high driving dynamics with g...(choose a part on the right to read more)
$4,345.00
Make a selection 47079801 Bmc sport air filters were originally developed in association with the ferrari f1 team. Bmc is one of the most recognized brands in the automotive industry and is the most successful filter in many types of racing. Oem filters only require a total particle filtration efficiency up to a minimum size of 10 microns. Oem air filters function primarily to protect the engine, so they are cost effectively produced in paper. Paper filters have high resistance to airflow that reduces the inlet pressure and consequently engine performance. A bmc sport filter contains an outer epoxy coated alloy mesh with internal layers of cotton gauze that have been immersed in a low viscosity oil. That technique ensures protection fro...(choose a part on the right to read more)
$214.50
Make a selection 100332195 The K&N filter charger air filter is designed to achieve high, virtually unrestricted air flow while maintaining filtration levels critical to ensure long engine life. Our automotive oe (original equipment) replacement air filters generally add 1-4 horsepower.
$161.70
Make a selection 100105149 Our upgraded sport camshafts offer incredible performance gains across the entire rpm range while retaining around town street-ability. These camshafts are manufactured for use with hydraulic lifters and require no modification for the valve pockets on the pistons. Specifications: 1.50 mm at 0.00 mm sold individually. 1 necessary per car. General Fitment911 1994-98
From $3,369.71
Make a selection 93061221102 When your pads reach a critical level, these sensors will trigger a warning to alert you that your pads need to be changed. Be sure to purchase these in conjunction with your new brake pads. High-quality OEM replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 2 necessary per axle.
From $13.02
Make a selection 100105254 Our upgraded camshafts offer incredible performance gains across the entire rpm range while retaining around town streetability. General Fitment911 1994-98
$1,098.90
Make a selection FVDBSK351996002 Brake service kit contains: - brake discs - brake pads - caliper screws - warning contacts - damping plates everything you need to service your front brake complete.
$536.80
Make a selection 115900997BIT021 The pss 10 suspension kit provides the ultimate in performance tuning. The fully adjustable monotube gas shock absorbers offer a selection of nine precise compression and rebound settings. The front and rear progressive rate springs allow accurate adjustment of the vehicle ride height and center of gravity for the level of performance you seek. Handling and control are just a few twists away. Regardless of whether in daily motoring, on the nordschleife of the nurburgring at the weekend, in training courses or in club sports - it's all pure driving enjoyment! Product advantages at a glance: • bilstein mono-tube/inverted technology • bilstein road tested and tuned • high driving dynamics with g...(choose a part on the right to read more)
$4,345.00
Make a selection 115900997BIT02 Bilstein b16 damptronic not only engine performance but, above all, suspension technology contributes to the fascination of a Porsche sports car. Bilstein offers an range of active coil over systems of the current Porsche models with pasm. The coil over system is electronically adjustable. So pasm-function and car sensors like psm stays fully in function. In addition the height-adjustment offers a certified range of lowering. Discreet sporty looks and precisely defined response within both setup modes, accompanied by high driving dynamics and excellent residual ride comfort. Regardless of whether in daily motoring, on the nordschleife or the nurburgring on the weekend, on training courses or in club sports - it...(choose a part on the right to read more)
$3,867.60
Make a selection 115343615B6 Twintube strut assembly setting: b6 heavy duty (hd) drive type: awd position: front quantity per vehicle: 2 bilstein b6 heavy duty gas pressure shocks and struts are the ideal choice for most vehicles, including full-size sedans, suvs and trucks. These shocks provide improved handling and stability, without sacrificing ride comfort. They offer super damping ability that makes them ideal for the driver who demands superior performance, while maintaining an exceptional street ride. (green paint, steel body)
$485.10
Make a selection BES99125040S Perfect muffler for those looking for a more aggressive exhaust note without changing the factory catalytic converters. The added benefit is you can reuse your OEM catalytic converters for emissions purposes. + 25 hp & + 19 torque* - reuses OEM cats, perfect for those concerned about warranty. - open muffler design for added power. - weighs 19 lbs. (8,6 kg) - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - 4 on a scale of 1-10 in volume (1 being stock) below 3,000 rpms, 6 on a scale of 1-10 in volume under maximum load (3 being stock). - includes new clamps and muffler straps.* - made in Germany. - modular design for future 100 cell, 200 cell or cat bypass use. - more distinguished ...(choose a part on the right to read more)
$2,655.40
Make a selection 99360612701 Oxygen or lambda sensors are critical to your engines health. If the sensor is faulty you may experience poor gas mileage, rough idling or engine pinging. Sold individually. 2 necessary per car. Left or right side fitment. View/Change Diagram
From $106.70
Make a selection 99360611400 This temperature sensor is located on the intercooler intake pipe at the back of the intercooler. It monitors the air temperature / density, which affects the fuel mixture. Be sure to replace it when necessary as it can cause an increase in emissions or fuel consumption. Sold individually. 1 necessary per car. View/Change Diagram
From $24.44
Make a selection BES99105040S Perfect muffler for those looking for a more aggressive exhaust note without changing the factory catalytic converters. The added benefit is you can reuse your OEM catalytic converters for emissions purposes. + 15 hp & + 12 torque - reuses OEM cats, perfect for those concerned about warranty. - open muffler design for added power. - tubing diameter is the same as the OEM system. - weighs 19 lbs. (8,6 kg) - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - 4 on a scale of 1-10 in volume (1 being stock) below 3,000 rpms, 6 on a scale of 1-10 in volume under maximum load (3 being stock). - includes cone and v band style hardware to prevent exhaust leaks. - made in Germany. - modular desi...(choose a part on the right to read more)
$2,920.50
Make a selection 99110613802 The radiator is a critical engine component that needs to be inspected and cleaned of debris to keep them functioning efficiently. If damage is noticed, replace it with this hello OEM high-quality OEM (original equipment manufacturer) replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. We recommend replacing the upper and lower rubber mounts, part # 99110653701 and 99110653802 sold individually. 1 necessary per car. Please note: please check the model fitment tab to ensure accurate fitment. This part is the latest supersession and can also be used in place of part number 991 106 138 01.
From $1,042.80
Make a selection 115333615B6 46mm monotube shock absorber setting: b6 heavy duty (hd) drive type: awd position: rear quantity per vehicle: 2 bilstein b6 heavy duty monotube gas pressure shocks and struts are the ideal choice for most vehicles, including full-size sedans, suvs and trucks. These shocks provide improved handling and stability, without sacrificing ride comfort. They offer super damping ability that makes them ideal for the driver who demands superior performance, while maintaining an exceptional street ride. (yellow paint, steel body)
$367.40
Make a selection BES99102240SHD + 15 hp & + 14 torque - 200 cell high flow, tri metal German hjs "hd" high durability matrix sports catalysts. - can be used with FVD "brombacher" mufflers. - weighs 15.5 lbs. (7.0 kg). - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - made in Germany. - intoxicating growl at idle, partial throttle and wide open throttle. The catalytic converter cores used in this system are the most advanced in the industry. They are produced by hjs in Germany and are a 200 cpsi (cell per square inch) tri-metal design. Tri-metal cats are the freest flowing and environmentally friendly aftermarket cats produced today. Tri-metal catalytic converters are rodium, platinum and iridium coated and per...(choose a part on the right to read more)
$3,293.40
Make a selection 99310117054 This is the original stud used in the rennsport and turbo (m64.20 / 60) models. We recommend them for your next engine rebuild. Sold individually. 24 necessary per car.
From $53.90
Make a selection F91641202TU05S Instrument faces are one of the most visible and frequently looked at components in your Porsche. When making the decision to change them you want to make ensure that you select a high-quality product like your originals. Each of our sets are made in Germany and use the factory scripting (font). Our faces also offer the same uniform night time shading and includes the original die cut notches for easy installation. Each kit varies, so simply pick out the faces that match your originals. They are available in a variety of colors to make a bold statement, or to match exterior paint schemes. Don't see the color or combination that is right for your car? Or perhaps you want a custom logo in the tach? Kindly contac...(choose a part on the right to read more)
$1,021.90
Make a selection F6564120102 Instrument faces are one of the most visible and frequently looked at components in your Porsche. When making the decision to change them you want to make ensure that you select a high quality product similar to your originals. Each of our sets are made in Germany and use the factory scripting (font). Our faces also offer the same uniform night time shading and includes the original die cut notches for easy installation. Each kit is made for global distribution, so simply pick out the faces that match your originals. They are available in a variety of colors to make a bold statement, or to match exterior paint schemes. This kit includes faces for: manual transmission / tiptronic transmission / kph / mph / celsi...(choose a part on the right to read more)
$603.90
Make a selection F6564120106 Instrument faces are one of the most visible and frequently looked at components in your Porsche. When making the decision to change them you want to make ensure that you select a high quality product similar to your originals. Each of our sets are made in Germany and use the factory scripting (font). Our faces also offer the same uniform night time shading and includes the original die cut notches for easy installation. Each kit is made for global distribution, so simply pick out the faces that match your originals. They are available in a variety of colors to make a bold statement, or to match exterior paint schemes. This kit includes faces for: manual transmission / tiptronic transmission / kph / mph / celsi...(choose a part on the right to read more) General Fitment911 1989-94911 1994-98
$603.90
Make a selection F91641200TUM041 The differences are day… and night! Gauge faces are one of the most visible and frequently looked at components in your Porsche. Why skimp on quality? Gauge faces should have clearly visible markings and be easy to read with and without back lighting. Replacement faces should offer similar qualities, but many gauge faces on the market don't quite make the grade. FVD gauge faces are different. What makes them different you ask? See for yourself. In the below pictures you will see that the tiptronic is an FVD gauge face and the 6 speed gauge face is the competitions. The daytime difference (the competition): darker, more yellow appearance raised orange warning lights, not flush larger, bolder script than t...(choose a part on the right to read more)
$858.00
Make a selection F91641200TUM07 The differences are day… and night! Gauge faces are one of the most visible and frequently looked at components in your Porsche. Why skimp on quality? Gauge faces should have clearly visible markings and be easy to read with and without back lighting. Replacement faces should offer similar qualities, but many gauge faces on the market don't quite make the grade. FVD gauge faces are different. What makes them different you ask? See for yourself. In the below pictures you will see that the tiptronic is an FVD gauge face and the 6 speed gauge face is the competitions. The daytime difference (the competition): darker, more yellow appearance raised orange warning lights, not flush larger, bolder script than t...(choose a part on the right to read more)
$858.00
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |