PORSCHE 911 REAR SUSPENSIONCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 911 1998-05 - Front Axle/Steering (includes uncategorized and accessory items) 150PB100915 Replace worn-out original sway bar bushings with this longer lasting poly-graphite plastic bushing. Poly-graphite is higher density than OEM rubber, so suspension components will experience less deflection. It is specially formulated with a graphite lubricant to produce a bearing like action. We also recommend replacing the sway bar to ball pin bushing at the same time to save on labor costs, part # 90134378200 sold individually. 4 necessary per car. Please note: this fit's genuine rear sway bars only.
$44.00
Make a selection 115900997BIT011 The pss 10 suspension kit provides the ultimate in performance tuning. The fully adjustable monotube gas shock absorbers offer a selection of nine precise compression and rebound settings. The front and rear progressive rate springs allow accurate adjustment of the vehicle ride height and center of gravity for the level of performance you seek. Handling and control are just a few twists away. Regardless of whether in daily motoring, on the nordschleife of the nurburgring at the weekend, in training courses or in club sports - it's all pure driving enjoyment! Product advantages at a glance: • bilstein mono-tube/inverted technology • bilstein road tested and tuned • high driving dynamics with g...(choose a part on the right to read more)
$4,345.00
Make a selection 150PB1027 Replace worn-out original sway bar bushings with this longer lasting poly-graphite plastic bushing. Poly-graphite is higher density than OEM rubber so suspension components will experience less deflection. It is specially formulated with a graphite lubricant to produce a bearing like action. We also recommend replacing the sway bar to ball pin bushing at the same time to save on labor costs, part # 90134378200 sold individually. 4 necessary per car. Please note: this fit's 911 models from 1978-89 if fitted with an 18mm original rear sway bar.
$49.50
Make a selection 150PB100916 Replace worn-out original sway bar bushings with this longer lasting poly-graphite plastic bushing. Poly-graphite is higher density than OEM rubber, so suspension components will experience less deflection. It is specially formulated with a graphite lubricant to produce a bearing like action. We also recommend replacing the sway bar to ball pin bushing at the same time to save on labor costs, part # 90134378200 sold individually. 4 necessary per car. Please note: this fit's genuine rear sway bars only.
$44.00
Make a selection 1150002LI These are made with club sport events in mind. They work with stiffer springs and lowering springs (we recommend h&r or eibach) and have a fully threaded body for individual lowering like the original 993 cup suspension. Lowering is adjustable to 35 mm (1.37 inches) sold individually. For matching club sport shocks, please order part # 1150002re for the right and 2 qty. Part # 1150009 for the rear. For a properly spec'd complete kit including front and rear club sport shocks with lowering springs and rear drop links, please order part # FVD33399300.
$517.00
Make a selection 150PB100919 Replace worn-out original sway bar bushings with this longer lasting poly-graphite plastic bushing. Poly-graphite is higher density than OEM rubber, so suspension components will experience less deflection. It is specially formulated with a graphite lubricant to produce a bearing like action. We also recommend replacing the sway bar to ball pin bushing at the same time to save on labor costs, part # 90134378200 sold individually. 4 necessary per car. Please note: this fit's genuine rear sway bars only.
$44.00
Make a selection 115900996BIT02 The pss 10 suspension kit provides the ultimate in performance tuning. The fully adjustable monotube gas shock absorbers offer a selection of nine precise compression and rebound settings. The front and rear progressive rate springs allow accurate adjustment of the vehicle ride height and center of gravity for the level of performance you seek. Handling and control are just a few twists away.
$4,802.60
Make a selection FVD333007 These high quality, German made mounts are made specifically for rear shock absorbers that contain a 15mm i.d. Uniball spherical bearing. They are located at the base of the rear shocks, and secure the shock to the rear trailing arms. They are required with FVD exclusive suspension kits with part #'s 115 900 911 xx / xxx. For example 115900911030 they are also required for rear shocks like part # FVD33315755 sold as a set. 1 necessary per car.
$174.90
Make a selection BBI9914010006 The bbi street cup suspension package improves the handling response of the vehicle by upgrading the factory springs with an improved linear rate springs and replacing the factory arms and links with the motorsport cup version that uses spherical bearings.
$7,295.00
Make a selection BK7032 Originally published by floyd clymer this is a faithful reproduction of the 1969 publication of that manual. By far the most comprehensive manual ever published for the 912 Porsche it includes complete technical data, service and maintenance information and comprehensive detailed instructions for the repair and overhaul of all major and minor mechanical and electrical components, making it an invaluable resource for collectors and restorers of these classic automobiles. There are separate sections that deal with the repair and overhaul procedures for the engine, ignition system, fuel system, clutch, transmission, rear suspension, steering, front suspension, brakes, heater, exhaust and emission control system pl...(choose a part on the right to read more) General FitmentACCESSORY
$39.95
Make a selection FVD33150020 This kit is complete and includes the front and rear monoball cartridges with press tools. Our weather sealed monoball cartridges are crafted in high carbon steel and 7075 t6 aircraft aluminum. They will positively locate the suspension arms so suspension motion is accurately repeated in every corner. Sold as a set of 4. 1 kit is necessary per car. Please note: noise may resonate inside the cabin during street use.
$715.00
Make a selection FVD33150003 Rear toe control arms - order in pairs only restore proper suspension geometry with this adjustable lower rear control arm. The factory control arm can't compensate enough when lowering your Porsche, leaving you stuck with as much as ½ of toe in. The result is poor handling and rapid tire wear. This kit will provide the additional adjustment needed. The adjusting link has a left and right hand thread on each end. Rotating the link will increase or decrease the overall length of the arm. A precision teflon lined spherical rod end replaces the compliant rubber factory bushing for improved suspension response and feedback, and also reduces toe changes during acceleration and deceleration.
$218.90
Make a selection FVD33150040R Replace worn-out original rear sub frame (side panel) bushings with our FVD clubsport series. They are made of rubber with an 85 shore hardness value, that is the same as the rennsport models. 85 shore is more durable, provides more positive suspension location and is still quiet and comfortable for street use. This bushing is made in Germany. It is crafted in high carbon steel and 7075 t6 aircraft aluminum and includes an 85 shore hardness value core. This is a front and rear bushing for one sub frame. 2 are necessary per car. We also sell the entire right and left rear sub frames with these bushings already installed, please order our part # FVD331993001.
$429.00
Make a selection FVD33150001 Solid bushings and mounts allow you to achieve exact suspension articulation which improves handling and stability on lowered / race prepared cars. The original soft rubber bushings can deform under track loads which allows the sub frame to shift and throw the camber and toe off. Solid bushings will not deform and will keep the camber and toe settings in line which equates to confidence in cornering and faster lap times. These are intended to replace the soft rubber bushings on the original rear sub frame (part #'s 993 331 051 00 & 993 331 052 00). They are made in Germany and are TUV approved. Sold as a set. 1 set is necessary per car. Please note: if you are also driving your car on the street, they will res...(choose a part on the right to read more)
$243.10
Make a selection FVD33399600B6 Bilstein suspension featuring with upside/down technology. Lowering 35 mm front and 30 mm rear - giving it a GT3 stance
$2,442.00
Make a selection FVD33398701 Bilstein suspension featuring with upside/down technology. Lowering 35 mm front and 30 mm rear - giving it a GT3 stance.
$2,803.90
Make a selection FVD33399602B6 Bilstein suspension featuring eibach springs. Lowering 35 mm front and 30 mm rear - giving it a GT3 stance
$1,930.50
Make a selection FVD33399600B8 Bilstein suspension featuring with upside/down technology. Lowering 35 mm front and 30 mm rear - giving it a GT3 stance
$2,310.00
Make a selection FVD33399602B8 Bilstein suspension featuring eibach springs. Lowering 35 mm front and 30 mm rear - giving it a GT3 stance
$1,944.80
Make a selection FVD341999R Replace worn-out original soft rubber (65 shore hardness value) control arm bushings with our FVD clubsport series. They are made from rubber with a 85 shore hardness value which is the same as the rennsport models. 85 shore is more durable, provides more positive suspension location and is quiet and more forgiving than a monoball upgrade. This is the ideal upgrade for street and light track / clubsport use. This bushing set is made in Germany, weather sealed, crafted in high carbon steel and 7075 t6 aircraft aluminum and includes 85 shore hardness value cores. This is a front and rear bushing for the front lower control arm (wishbone). 2 sets are necessary per car.
$124.30
Make a selection 7213312 Complete your performance suspension upgrade with the eibach anti-roll kit performance sway bars. While the eibach pro-kit and sportline performance spring kits are regarded as the primary suspension performance enhancement, the eibach anti-roll kit sway bars substantially reduce body-roll through increased design stiffness over your vehicles stock bars. The impressive results are increased balance, handling and cornering grip in all performance-driving situations. General Fitment911 1998-05911 1994-98
$334.99
Make a selection SCSBSCCFR096 At last, a strut tower brace that looks as good as it performs. Schnell performance is proud to announce it's all new, highly developed strut brace made of carbon fiber and anodized aluminum. This design, pound for pound, is stiffer than other aluminum bars on the market. The anodized brackets bolt up with very little effort, making installation a cinch. Tighten up your cars suspension now for safer, quieter and more accurate steering and braking. General Fitment911 1998-05
$268.65
Make a selection SCSBSBALR096 At last, a strut tower brace that looks as good as it performs. Schnell performance is proud to announce it's all new, highly developed strut brace made of aircraft grade, polished aluminum. This design, pound for pound, is stiffer than other aluminum bars on the market. The anodized brackets bolt up with very little effort, making installation a cinch. Tighten up your cars suspension now for safer, quieter and more accurate steering and braking. General Fitment911 1998-05
$187.65
Make a selection 115910996034 Bilstein b4 OEM m030 (original m030 suspension) shock absorber set (4 pieces) for cars with lowering springs or cars delivered with factory m030 sport suspension. Nothing is better than the original! The b4 m030 dampers from bilstein are the perfect shock absorber for lowered cars. Facts: - constant damping pressure under load - increased driving stability - increased durability - OEM quality - bilstein gas pressure technology - type/model m030
$1,784.11
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |