PORSCHE 356C ALUMINUMCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 911 1998-05 - Fuel/Exhaust (includes uncategorized and accessory items) 115971AAR01 Panamera models with optional air suspension utilize four sensors to control the ride height. This is accomplished via the use of a small linkage or link which connects the sensor to the suspension. As the car is raised or lowered, the link moves the sensor up or down sending a signal to the computer telling it how high the car is. When you replace the non-adjustable factory link with this adjustable design, the output of the sensor makes the computer believe that the car is higher than it is. So, the computer will lower the ride height. The simplicity of this setup is that it retains full functionality of the factory system. Be warned, all adjustable lowering links are not the same! These links are machined al...(choose a part on the right to read more)
$324.50
Make a selection 115900997TTCS The ultimate bilstein sport suspension for club racing and street performance! This suspension was developed under real racing conditions by bilstein with double world rally champion walter rohrl. - reduced weight via the use of an integrated reservoir. - 2 way damping adjustment (bound (red) and rebound (blue) independently). - dials with good visibility and scaling (from 1 to 10). - easy to adjust when installed with click screening and color coding. - bilstein mono-tube gas pressure technology. - adjustable aluminum uniball camber plates (rear). - TUV approved. - made in Germany. What's in the box: - adjustable dampers including double springs. - rear uniball camber plates. - spring tensioning key (tool). -...(choose a part on the right to read more)
$7,256.70
Make a selection FVD3522P18027A The brembo gran turismo (gt) braking system is ideal for use on the street and for light track use. This GT system expands upon the original drilled disc's face type made by Porsche. The cross drilled disc surface continuously refreshes the braking surface and offers the highest initial response of any disc type. So, you can confidently respond to sudden pedestrian or traffic movement with maximum braking performance. Drilled discs operate in a wide range of operating temperatures and environments and respond confidently in wet weather. The GT line is dedicated to the most demanding customers. It originates from racing components, consisting of floating ventilated cross drilled discs, aluminum calipers with op...(choose a part on the right to read more)
$4,064.50
Make a selection FVD35161115 Wheel spacers make your tires and wheels appear wider by moving the wheel out from the hub, providing both performance and appearance improvements. Whether you want improved handling, increased safety, or simply desire your car to make a statement about your individual style, wheel spacers can help you accomplish your goal. This spacer includes a hub centric design that makes the spacer act as a precise extension of the axle hub for wheel balance. It bolts to the hub by reusing the existing wheel studs, the wheel is then bolted to the spacer studs and affixed with included nuts. Size: 15 mm (.59 inches) bolt pattern: 5/130 center bore: 71.6 bolt / stud: stud thread type: 14x1.5 material: strength tested aluminu...(choose a part on the right to read more)
$103.40
Make a selection FVD35161107B Wheel spacers make your tires and wheels appear wider by moving the wheel out from the hub, providing both performance and appearance improvements. Whether you want improved handling, increased safety, or simply desire your car to make a statement about your individual style, wheel spacers can help you accomplish your goal. This spacer fits between the wheel and hub. Size: 7 mm (.275 inches) bolt pattern: 5/130 center bore: 71.6 bolt / stud: n/a thread type: 14x1.5 material: strength tested aluminum alloy coating: anodized for corrosion protection hub alignment set screws are included. Longer bolts sold separately depending on application. Made in Germany. Sold individually. Can be used in front and/or rear. No...(choose a part on the right to read more)
$108.88
Make a selection FVD33150046 Replace worn-out original soft rubber track rod bushings with these OEM replacements. They are made of rubber that has a 65-shore hardness value, just like the oem. They will restore the original ride comfort and are more forgiving than the clubsport (85 shore rubber). This bushing is made in Germany, weather sealed, crafted in high carbon steel and 7075 t6 aircraft aluminum and includes a 65-shore hardness value core. Sold individually. 8 are necessary per car. Please note: this does not include the track rod, the picture circled in red is just for reference.
$60.50
Make a selection FVD35161126 Wheel spacers make your tires and wheels appear wider by moving the wheel out from the hub, providing both performance and appearance improvements. Whether you want improved handling, increased safety, or simply desire your car to make a statement about your individual style, wheel spacers can help you accomplish your goal. This spacer includes a hub centric design that makes the spacer act as a precise extension of the axle hub for wheel balance. It bolts to the hub by reusing the existing wheel studs, the wheel is then bolted to the spacer studs and affixed with included nuts. Size: 26 mm (1.02 inches) bolt pattern: 5/130 center bore: 71.6 bolt / stud: stud thread type: 14x1.5 material: strength tested alumin...(choose a part on the right to read more)
$132.00
Make a selection FVD35161118 Wheel spacers make your tires and wheels appear wider by moving the wheel out from the hub, providing both performance and appearance improvements. Whether you want improved handling, increased safety, or simply desire your car to make a statement about your individual style, wheel spacers can help you accomplish your goal. This spacer includes a hub centric design that makes the spacer act as a precise extension of the axle hub for wheel balance. It bolts to the hub by reusing the existing wheel studs, the wheel is then bolted to the spacer studs and affixed with included nuts. Size: 18 mm (.708 inches) bolt pattern: 5/130 center bore: 71.6 bolt / stud: stud thread type: 14x1.5 material: strength tested alumin...(choose a part on the right to read more)
$115.50
Make a selection FVD10699703 For 996 turbo and 997 turbo, 996 GT3l. Fits left side. - specially designed for tuned and motorsport vehicles the racing & high performance division of csf build and engineer the most advanced, efficient, and reliable cooling systems in the world. Csf manufacturers radiators with high performance all-aluminum and direct-fit replacement for racecars. The only high performance manufacture to feature this advanced technology. These radiators are stamped to the same geometry of the application's original plastic end radiators. These tanks feature less welding, and are generally considered the strongest tank designs in the industry.
$768.90
Make a selection E13209 Introducing the latest in tow hook innovation: engineered with an increased side load capacity and adjustable-length rigid mount receiver. This tapered stainless loop design incorporates a new locking function to maintain your preferred loop position. Additional features include machined graphics, rotational timing and camera mount compatibility.
$145.00
Make a selection FVD35161103B Wheel spacers make your tires and wheels appear wider by moving the wheel out from the hub, providing both performance and appearance improvements. Whether you want improved handling, increased safety, or simply desire your car to make a statement about your individual style, wheel spacers can help you accomplish your goal. This spacer fits between the wheel and hub. Size: 7 mm (.275 inches) bolt pattern: 5/130 center bore: 71.6 bolt / stud: n/a thread type: 14x1.5 material: strength tested aluminum alloy coating: anodized for corrosion protection hub alignment set screws are included. Longer bolts sold separately depending on application. Made in Germany. Sold individually. Can be used in front and/or rear. No...(choose a part on the right to read more)
$40.70
Make a selection FVD35161165 Wheel spacers make your tires and wheels appear wider by moving the wheel out from the hub, providing both performance and appearance improvements. Whether you want improved handling, increased safety, or simply desire your car to make a statement about your individual style, wheel spacers can help you accomplish your goal. This spacer includes a hub centric design that makes the spacer act as a precise extension of the axle hub for wheel balance. It bolts to the hub by reusing the existing wheel studs, the wheel is then bolted to the spacer studs and affixed with included nuts. Size: 65 mm (2.55 inches) bolt pattern: 5/130 center bore: 71.6 bolt / stud: stud thread type: 14x1.5 material: strength tested alumin...(choose a part on the right to read more)
$317.90
Make a selection FVD3511M18002A The brembo gran turismo (gt) braking system is ideal for use on the street and for light track use. This GT system expands upon the original drilled disc's face type made by Porsche. The cross drilled disc surface continuously refreshes the braking surface and offers the highest initial response of any disc type. So, you can confidently respond to sudden pedestrian or traffic movement with maximum braking performance. Drilled discs operate in a wide range of operating temperatures and environments and respond confidently in wet weather. The GT line is dedicated to the most demanding customers. It originates from racing components, consisting of floating ventilated cross drilled discs, aluminum calipers with op...(choose a part on the right to read more)
$4,394.50
Make a selection FVD34307101 Our direct replacement, OEM quality link uses rubber with a shore hardness value of 85. That is the same value as the rennsport models from Porsche. This link will offer superior performance under high cornering loads, more durability and are still forgiving for street use. Road noise not compromised with our links either. Facts: made in Germany. Crafted from high carbon steel and 7075 t6 aircraft aluminum. Weather sealed. Sold individually. Please note: we recommend buying these as a set, please purchase the right link, our part # FVD34307201
$93.50
Make a selection FVD3511B18022A This line is dedicated to the most demanding customers. This braking system originates from the racing components, consisting of a ventilated, integral or composite disc, aluminum calipers, a complete set of high performance brake pads, TUV/dot homologated metal-braided brake hoses and high quality fastener hardware. Calipers are available in red, black or silver. Proven on-track performance; extraordinarily powerful and consistent under the repeated loads. Disperses gasses, cleans pads for better "bite". Reduces "un-sprung weight" at each corner for better handling. Provides maximum braking force without the flex of sliding calipers. Reduces heat-related stress, increases brake performance and pedal feel. ...(choose a part on the right to read more)
$5,959.21
Make a selection FVD34791130 Enhance steering precision and steering feedback by simply replacing your original tie rods. Turbo tie rods use a spherical inner joint instead of soft rubber bushings. They offer quicker steering response, more sensitivity and more precision. These are standard length we highly recommend them for lowered vehicles with bump steer kits like part # FVD34791100 or FVD347911930 . We also offer turbo tie rods in longer lengths for other applications, check part # FVD34791180r and FVD34791181ry this kit is manufactured in Germany by an OEM supplier, made from high carbon steel and 7075 t6 aluminum. Kit includes: 2 qty. Outer tie rods 2 qty. Inner tie rods 2 qty. Spacing washers 2 qty. Boots 2 qty. Castle nuts 2 qty. ...(choose a part on the right to read more)
$222.24
Make a selection FVD341999R Replace worn-out original soft rubber (65 shore hardness value) control arm bushings with our FVD clubsport series. They are made from rubber with a 85 shore hardness value which is the same as the rennsport models. 85 shore is more durable, provides more positive suspension location and is quiet and more forgiving than a monoball upgrade. This is the ideal upgrade for street and light track / clubsport use. This bushing set is made in Germany, weather sealed, crafted in high carbon steel and 7075 t6 aircraft aluminum and includes 85 shore hardness value cores. This is a front and rear bushing for the front lower control arm (wishbone). 2 sets are necessary per car.
$124.30
Make a selection FVD35198001 Brembo direct replacement 2-piece rotors for the '04-'06 Porsche Carrera GT designed to be used with the vehicles OEM brake calipers. These include brembo's high thermal type iii rotors , billet aluminum bells, and anti-rattle floating hardware. The floating disc mounting system is designed to allow a specific amount of float in both radial and axial directions. Brembo has engineered special springs that are used on every other fastener in order to slightly preload the assembly.
$2,832.54
Make a selection FVD35161138 Wheel spacers make your tires and wheels appear wider by moving the wheel out from the hub, providing both performance and appearance improvements. Whether you want improved handling, increased safety, or simply desire your car to make a statement about your individual style, wheel spacers can help you accomplish your goal. This spacer includes a hub centric design that makes the spacer act as a precise extension of the axle hub for wheel balance. It bolts to the hub by reusing the existing wheel studs, the wheel is then bolted to the spacer studs and affixed with included nuts. Size: 35 mm (1.49 inches) bolt pattern: 5/130 center bore: 71.6 bolt / stud: stud thread type: 14x1.5 material: strength tested alumin...(choose a part on the right to read more)
$173.80
Make a selection FVD34307201 Our direct replacement, OEM quality link uses rubber with a shore hardness value of 85. That is the same value as the rennsport models from Porsche. This link will offer superior performance under high cornering loads, more durability and are still forgiving for street use. Road noise not compromised with our links either. Facts: made in Germany. Crafted from high carbon steel and 7075 t6 aircraft aluminum. Weather sealed. Sold individually. Please note: we recommend buying these as a set, please purchase the left link, our part # FVD34307101
$93.50
Make a selection FVD10699701 This radiator is produced by the racing & high-performance division of csf who design, engineer and manufacture the most advanced, efficient, and reliable cooling systems in the world. Csf manufacturers all aluminum high performance radiators that are a direct-fit replacement for Porsche racecars and streetcars. Csf radiators improve cooling efficiency by 10-20 % over the factory radiators. Each radiator is stamped to the same geometry and includes aluminum end tanks that offer more reliability than the factory plastic end tanks. Each csf end tank features quality welding and is generally considered the strongest tank design in the industry. If you are planning to upgrade or replace your radiators, we highly re...(choose a part on the right to read more)
$548.90
Make a selection FVDBRO1016003A Weight savings approximately 4kg (8.8 lbs) of rotating unsprung weight. Oem disk weight 10,8kg (23.8 lbs), brembo disk weight 8.9kg (19.69 lbs) rotors: (13") 330x34mm drilled discs bells / hats: precision milled billet aluminum hardware: brembo floating anti-rattle disc hardware by using an aluminum bell for the hub section of the disc, these rotor assemblies save a great deal of weight. Since this is both rotating and unsprung, it benefits the acceleration, braking, and handling of the vehicle. Secondly, it is better able to handle the large temperature changes that a brake disc experiences. The mounting system is designed to allow a specific amount of float in both radial and axial directions. Brembo has eng...(choose a part on the right to read more)
$1,815.00
Make a selection FVD512997GT3RST 997 GT3 rear spoiler fits 997turbo includes: deck lid, aluminum upright, 3rd brake light housing and kevlar/carbone wing (l= 145cm, b=28cm, h=7 cm) with end plates. Material: aluminum, fiberglass, kevlar-carbone. Also available with wing blade in fiber (gfk) FVD512997gt3rs tech tip: facelift models (2009- ), the 3rd brake light can usually be assumed. If necessary please order the 3rd brake light 99763105201 separately. The holes for the intake fan on the rear deck lid must be drilled prior to installation (model variations). Please note wing is fixed and is not adjustable. The air inlet of the rear is not included. Please order 99751262592g2x
$6,528.50
Make a selection FVD803607 Flat design - for gentle cleaning on steel and aluminum wheels - length: 27cm.
$7.70
Make a selection FVD803608 Conical design - for gentle cleaning of steel and aluminum wheels - length: 29cm.
$14.30
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |