PORSCHE 914 LOWER PARTCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 911 2005-08 - Fuel/Exhaust (includes uncategorized and accessory items) 90151107321 This is the rear release cable for the rear engine deck lid. It is 1900 mm in length. When replacing this cable, we also recommend replacing the handle, part # 90155281320 and the grommet, part # 91151253100. Also, check your rear lid lower lock, part # 90151205200, perfect time to replace it if it is corroded and the spring is worn. Sold individually. 1 necessary per car.
From $9.50
Make a selection 93060201501 Complete distributor without an exchange. This distributor has been completely remanufactured, which includes a full inspection, disassembly, cleaning and degreasing. We then install a toothed timing belt, 3 German made top bearings, 1 German made lower bearing and a distributor pinion pin (part # 930 602 922 00). We also install new dust caps, Bosch rotors and Bosch cap. Clearances, timing and proper operation are then checked to ensure reliability.
$2,534.48
Make a selection 91121152200 Engine compartment blower to rt. Heat exchanger; 60mm x 1100 mm. Not for ca models; original tan paper/aluminum
$20.09
Make a selection 91152104403R01 This is for a driver's side (left hand drive) sports seat that reclines. It is the right lower outer hinge cover that does not have a knob / lever. This is a genuine part sourced from Porsche ag in Germany to ensure quality, reliability and precise fitment. Sold individually. 1 necessary per car. Like new
$420.20
Make a selection 911606105HXATK The cis injection / k-jetronic warm up regulator is a critical component that performs the following functions: lowers pressure when engine is cold. Absorbs / distributes engine heat. Allows for an additional rich mixture under full load to prevent engine damage. Altitude correction. Send us your original part and we will have it remanufactured for you. We do not offer a core exchange on this part. Each part is remanufactured in Germany, so the lead times can vary. Sold individually. 1 necessary per car.
$744.70
Make a selection
$111.06
Make a selection 115384 If you are looking for added damping performance on the street, the bilstein b6 performance damper is the ideal solution. The product benefits at a glance: optimum adhesion and enhanced stability for daily driving and extreme driving situations. Marked improvement in safety and sportiness without additional spring changes. Increased service life. Bilstein gas pressure technology. Bilstein mono-tube/upside-down technology. Made in Germany. Road-tested and fine-tuned by bilstein. German TUV registration is not required. Sold individually. 1 necessary per car. We recommend adding our lowering spring collars if you would like a lower ride height, our part # 115110016
$640.20
Make a selection 1150002LI These are made with club sport events in mind. They work with stiffer springs and lowering springs (we recommend h&r or eibach) and have a fully threaded body for individual lowering like the original 993 cup suspension. Lowering is adjustable to 35 mm (1.37 inches) sold individually. For matching club sport shocks, please order part # 1150002re for the right and 2 qty. Part # 1150009 for the rear. For a properly spec'd complete kit including front and rear club sport shocks with lowering springs and rear drop links, please order part # FVD33399300.
$517.00
Make a selection 115385 If you are looking for added damping performance on the street, the bilstein b6 performance damper is the ideal solution. The product benefits at a glance: optimum adhesion and enhanced stability for daily driving and extreme driving situations. Marked improvement in safety and sportiness without additional spring changes. Increased service life. Bilstein gas pressure technology. Bilstein mono-tube/upside-down technology. Made in Germany. Road-tested and fine-tuned by bilstein. German TUV registration is not required. Sold individually. 1 necessary per car. We recommend adding our lowering spring collars if you would like a lower ride height, our part # 115110016
$640.20
Make a selection 99110613802 The radiator is a critical engine component that needs to be inspected and cleaned of debris to keep them functioning efficiently. If damage is noticed, replace it with this hello OEM high-quality OEM (original equipment manufacturer) replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. We recommend replacing the upper and lower rubber mounts, part # 99110653701 and 99110653802 sold individually. 1 necessary per car. Please note: please check the model fitment tab to ensure accurate fitment. This part is the latest supersession and can also be used in place of part number 991 106 138 01.
From $1,042.80
Make a selection 44404480060041 High quality polished lower switch cover. This is a carbon overlay, meant to be adhered to your original plastic lower switch cover. Great detail is taken to attempt to match the original weave size, color and polish. Whether you are adding carbon to the interior or matching existing pieces, this is high quality and is made in Germany so it is made to last, like the original. Sold individually. We also recommend replacing your missing or broken switch cover clips, part # 94455255700. 2 are needed per switch cover. If you would also like to replace your knobs, use part # FVD33399603b8
$514.80
Make a selection 93050306800 Steel, prime coated quarter panel extension, made by dansk. They offer a complete line of replacement bodywork to complement the entire Porsche model range. All dansk products are manufactured to European standards to ensure the quality that you expect for your Porsche. This commitment has made dansk one of the original equipment suppliers to the Porsche in Germany. Sold individually. 1 necessary per car. Please note: due to variances in production at the factory, age, accident damage or rust, each part may require trimming and or adjustment for perfect fitment.
$244.20
Make a selection FVD333007 These high quality, German made mounts are made specifically for rear shock absorbers that contain a 15mm i.d. Uniball spherical bearing. They are located at the base of the rear shocks, and secure the shock to the rear trailing arms. They are required with FVD exclusive suspension kits with part #'s 115 900 911 xx / xxx. For example 115900911030 they are also required for rear shocks like part # FVD33315755 sold as a set. 1 necessary per car.
$174.90
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |