Vehicles
Sections
166 not categorized PORSCHE 356 C WIL VICan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 911 2005-08 (includes uncategorized and accessory items) 99310605180 Allows you to convert to one fan belt to run the fan and alternator like the factory rs versions. Oem part sourced in Germany to ensure quality, reliability and precise fitment. Once installed the alternator will run at the fan speed. That will lessen the inertial load and will add slightly more horsepower and acceleration. - includes fasteners (3 qty. M 6x35) - weighs .4 lbs ( .17 kg) please note: for 993 race car conversions or for cars without a/c we also recommend the corresponding crankshaft pulley, part # 99310205040 sold individually. 1 necessary per car.
From $152.90
Make a selection 99160918100 When your pads reach a critical level, these sensors will trigger a warning to alert you that your pads need to be changed. Be sure to purchase these in conjunction with your new brake pads. High-quality OEM replacement designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 2 necessary per axle.
From $12.10
Make a selection 99334101802ATK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will properly install original control arm bushings. . Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrangements can be made for its return to you. We do not offer a core exchange on this part. Sold individually....(choose a part on the right to read more)
$418.00
Make a selection 99334703181 If your tie rod is worn, you will experience sloppy steering response and knocking / creaking sounds. Your tie rod keeps the steering centered, so failure can be dangerous and can seriously affect steering control. After replacing the tie rods, you will experience tighter, more precise feedback without noise. Tie rod consists of: 1 qty. Tie rod 1 qty. Hexagon nut (m14 x 1.5) 1 qty. Inner axial joint 1 qty. Lock nut we recommend replacing the right and left side tie rods at the same time. We also recommend replacing the bellows, part # pcg419831c sold individually. 2 necessary per car.
From $303.00
Make a selection 96434307181ATK Looking for a more cost-effective solution than ordering a new link? Let us recondition your original drop link. The reconditioning process includes full inspection, disassembly, degreasing and media blasting. Once fully prepared, we properly install new bushings, finish with a corrosion proof coating and include a new lock nut. Please note: each link is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your link we will notify you as soon as we can. Arrangements can be made for its return to you. Sold individually. 1 necessary per car.
$194.70
Make a selection 93010734706 This oil pipe is necessary when installing the oil line for the tensioner hose to camshaft carrier, part # 93010734714 we recommend purchasing, 1 qty. Banjo bolt n0210731 and 2 qty. Sealing rings, part # 90012311530 to complete the installation. This part is sourced in Germany to ensure quality, reliability and precise fitment. This will fit all the vehicles listed in the fitment tab and those that have been updated to pressure fed tensioners. Sold individually. 1 necessary per car.
From $24.75
Make a selection 93010734714 This part is sourced in Germany to ensure quality, reliability and precise fitment. This will fit all the vehicles listed in the fitment tab and those that have been updated to pressure fed tensioners. This line requires that you also purchase part # 93010734706 . We also recommend purchasing 1 qty. Union nut, part # 90010400303 and 1 qty. Cutting ring sleeve, part # n0208251 for installation. Also need the right side? Please order part # 93010734812 for the 911 3.2 l and 930 3.3l. Order part # 93010734815 for the 965 3.3 l. Sold individually. 1 necessary per car.
From $41.80
Make a selection 930602015AX2ATK Send us your distributor and we will remanufacture it for you. A perfect option for those who have time and want to save on costs. The remanufacturing process includes full inspection, disassembly, cleaning and degreasing. We then install a toothed timing belt (part # FVD 602 964 00) and a distributor pinion pin (part # 930 602 922 00). Clearances, timing and proper operation are then checked to ensure reliability. Please note: each distributor is remanufactured in Germany, so the lead times can vary.
$504.15
Make a selection 930602701XATK The cdi or hkz as it is known in Germany, is the high-voltage condenser ignition control unit. Aging cdi / hkz units lead to deterioration of performance with time. A failing unit's symptoms include a fluctuating tach, stalling, loss of power to the ignition coil and no start situations, leaving you stranded. Send us your original cdi / hkz and German technicians with many years of experience will completely remanufacture it to new specifications. This is not a repaired unit like many of our competition offer, this is a completely remanufactured unit using new upgraded components. The remanufacturing process includes: disassembly inspection and cleaning complete diagnosis (including oscillogram) on a test benc...(choose a part on the right to read more)
$823.90
Make a selection 93061221102 When your pads reach a critical level, these sensors will trigger a warning to alert you that your pads need to be changed. Be sure to purchase these in conjunction with your new brake pads. High-quality OEM replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 2 necessary per axle.
From $13.02
Make a selection 99333104503ATK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will properly install the bushings. Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrangements can be made for its return to you. We do not offer a core exchange on this part.
$254.10
Make a selection 92834102833ATK By ordering this part number you get after previous sending in your wishbone overhauled with new silent blocs back. Should it not be repairable, we will inform you immediately.
$342.10
Make a selection 96453109600EQ This is a genuine door seal that seals the entire door and window frame. As these classics age the original gasket can become brittle and will crack, so it is essential that it is in good order as it keeps moisture out of the cabin. Sold individually. 1 necessary per car.
$215.60
Make a selection 90110705903 The new oil cooler for the Porsche 914-6 is based on the incredibly popular and successful csf 911/930 turbo engine oil cooler (csf #8242). Both of these oil coolers went through 2+ years of development and multiple rounds of prototypes. The csf Porsche 914-6 engine oil cooler’s world debut at rennsport reunion 2023 was met with incredible support and enthusiasm from the community. Obviously air-cooled enthusiasts know the struggles associated with the oil cooler located on the engine block of the old flat six motor. With the 914-6 swaps/conversions becoming ever more popular, this new oil cooler will be a game changer for classic Porsche owners and restoration shops.
From $1,030.00
Make a selection 99334101702ATK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will properly install original control arm bushings. . Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrangements can be made for its return to you. We do not offer a core exchange on this part. Sold individually....(choose a part on the right to read more)
$418.00
Make a selection 83789680072 Stoptech big brake kit front drilled red caliper Porsche 996 Carrera s 2005 General Fitment911 2005-08
$3,882.60
Make a selection 96560612601EQ Oxygen or lambda sensors are critical to your engines health. If the sensor is faulty you may experience poor gas mileage, rough idling or engine pinging. High-quality replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Be sure to check the "fits these models" tab to make sure that this will work for your needs. Sold individually. 1 necessary per car.
$111.10
Make a selection 96437502301ATK Send us your OEM transmission mount bracket and we will restore it to better than new condition! Our service includes removal of the old mount, media blasting, proper installation of the new mount and protective seal coating. Our mount is remanufactured in europe by an OEM supplier using the finest materials. It is a 65 shore rubber hardness value which is the same as the what was standard on these cars. Simply order and send us your OEM bracket, we will take care of the rest. Approximate lead time is estimated between 3-6 weeks.
$178.20
Make a selection 9780929758268 The second edition of this book continues the restoration of a 356 Porsche to driver level condition. This book does not spend time or money creating the “perfect” 356, and does not necessarily search for nos (new old stock) replacement panels if a reproduction panel or patch is appropriate; but the book strives to give you a restoration that will be correct, admired and driven. This second edition provides more detail and contains additional comments to assist those restoring a 356 which was purchased disassembled. this second edition follows the restoration of a 1957 sunroof coupe from the time of purchase to the first drive. additionally, detailed comments are provided from vendors, such as media blast...(choose a part on the right to read more) General FitmentACCESSORY
$29.50
Make a selection 96434705804SP We are committed to Porsche cars and are very happy to release an inner tie rod that consists of a monoball joint. Until now this was something that was really only available on racing models. Our tie rod will provide you with unequalled steering precision for street and track use. This component is manufactured in europe and contains the finest materials available, high carbon steel and 7075 t6 aluminum. Installation is seamless, this is a direct replacement for the OEM number, 964 347 032 00. We also suggest replacing your outer tie rods, part # 96434703200 (qty. 2 are needed) and now is also a good time to replace your worn out inner tie rod dust bellows, part # 96434719103. Please note: this is not for the ...(choose a part on the right to read more)
$196.90
Make a selection 96437502301RATK Send us your OEM transmission mount bracket and we will restore it to better than new condition! Our service includes removal of the old mount, media blasting, proper installation of the new mount and protective seal coating. Our transmission mount is manufactured in europe by an OEM supplier using the finest materials (high carbon steel, 7075 t6 aluminum and 85 shore rubber - rs spec). Simply order and send us your OEM bracket, we will take care of the rest. Approximate lead time is estimated between 3-6 weeks.
$176.00
Make a selection 97182 All of the ipd "competition" plenums utilize the next largest size throttle body offered by Porsche. In this case, the competition Carrera upgrades the factory oe 74mm throttle body with Porsches 82mm 997 GT3 throttle body. All of our competition plenums are designed to perform with cars equipped with high performance exhaust systems. The more extensive the exhaust system (headers, kats and mufflers) the better. Optimizing air intake and exhaust together creates a balanced performance package that allows the engine to inhale and exhale more air thus creating more power and torque. General Fitment911 2005-08
$1,208.25
Make a selection 964347009BXATK This steering rack is a remanufactured part with a core, as such an additional charge (a core deposit) will be added to the purchase price of the part. After receiving your new part, kindly send back your old part, or core . Once the core is returned to us and it has been inspected to ensure it is rebuild-able and resell-able, the core deposit will be refunded. The remanufacturing process includes full inspection and testing for structural integrity. We then disassemble and bead blast to remove corrosion. Internals are micro-finished to OEM specifications. Sealing surfaces are carefully checked and restored prior to installing new premium seals and o-rings. Each unit is then carefully tested for full functional...(choose a part on the right to read more)
$1,633.50
Make a selection
From $106.00
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |