PORSCHE 986 WE NEED A CARCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 911 2009-12 - Brakes/Wheels (includes uncategorized and accessory items) 96442422300 Restore precise shifting with this OEM shift coupler bushing. To save on installation cost / time, we recommend installing a new conical screw, part # 90142422900 coupler sleeves / boots, part # 91142429400 and 91142429200 be sure to check / replace the shift rod bushing as well, part # 91142413900, the friction ring, part # 91442422400 this is a high-quality OEM (original equipment manufacturer) replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 2 necessary per car.
From $5.60
Make a selection 96453109600EQ This is a genuine door seal that seals the entire door and window frame. As these classics age the original gasket can become brittle and will crack, so it is essential that it is in good order as it keeps moisture out of the cabin. Sold individually. 1 necessary per car.
$215.60
Make a selection 964541225001 This genuine Porsche windshield seal is an integral part of keeping your cowl from rusting. It is critical that the gasket and windshield are properly installed to prevent corrosion. Sold individually. 1 needed per car. Please note: for the 911 models, this does not contain the trim frame slot for chrome / black trim like the earlier cars.
$406.00
Make a selection 96560612601EQ Oxygen or lambda sensors are critical to your engines health. If the sensor is faulty you may experience poor gas mileage, rough idling or engine pinging. High-quality replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Be sure to check the "fits these models" tab to make sure that this will work for your needs. Sold individually. 1 necessary per car.
$111.10
Make a selection 99150552580OK1 This spoiler tends to become scratched, scraped or torn off with time and detracts from your car's appearance. They are a vital downforce component and should be replaced when damaged. This is a genuine part sourced from Porsche ag in Germany to ensure quality, reliability and precise fitment. Sold individually. 1 necessary per car.
From $749.50
Make a selection 99157362300 A clean cabin air filter reduces dust, dirt, allergens and odor. It will also increase the airflow from the cabin vents. Be sure to replace yours as recommended to keep consistent air quality. High-quality mann OEM (original equipment manufacturer) replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 1 necessary per car. Please note: please check the model fitment tab to ensure accurate fitment since this fits multiple models / applications. We also recommend replacing the exterior cabin air filter, part # 99157237100
From $22.25
Make a selection 99160918500 When your pads reach a critical level, these sensors will trigger a warning to alert you that your pads need to be changed. Be sure to purchase these in conjunction with your new brake pads. High-quality OEM replacement designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 2 necessary per axle. Please note: please check the model fitment tab to ensure accurate fitment.
From $24.84
Make a selection 99310605180 Allows you to convert to one fan belt to run the fan and alternator like the factory rs versions. Oem part sourced in Germany to ensure quality, reliability and precise fitment. Once installed the alternator will run at the fan speed. That will lessen the inertial load and will add slightly more horsepower and acceleration. - includes fasteners (3 qty. M 6x35) - weighs .4 lbs ( .17 kg) please note: for 993 race car conversions or for cars without a/c we also recommend the corresponding crankshaft pulley, part # 99310205040 sold individually. 1 necessary per car.
From $152.90
Make a selection 99334703181 If your tie rod is worn, you will experience sloppy steering response and knocking / creaking sounds. Your tie rod keeps the steering centered, so failure can be dangerous and can seriously affect steering control. After replacing the tie rods, you will experience tighter, more precise feedback without noise. Tie rod consists of: 1 qty. Tie rod 1 qty. Hexagon nut (m14 x 1.5) 1 qty. Inner axial joint 1 qty. Lock nut we recommend replacing the right and left side tie rods at the same time. We also recommend replacing the bellows, part # pcg419831c sold individually. 2 necessary per car.
From $303.00
Make a selection 99335513901EQ Classic Porsche flexible brake hoses can suffer from dry rot and can eventually split and leak fluid, creating a serious safety concern. This line is a high quality replacement, designed to perform like the original and has the same length and threaded ends. It also includes a protective spring frame that keeps the line in place and prevents kinks. We recommend inspecting all of your brake lines and hoses the next time you change your brake pads. Sold individually. 2 necessary per car.
$73.70
Make a selection 99660610599 If you are noticing engine vibrations, misfires and even backfiring your crankshaft position sensor maybe bad. Your car's dme (ecu) uses the signal from the crankshaft position sensor to control ignition timing and fuel injection, so if your sensor is failing your engine is suffering from poor timing and is not running efficiently. This kit is complete and ready to install.
$132.77
Make a selection 9A110514203 Timing chains are critical engine components that should be addressed as soon as wear or stretching is noticed. The first indication is typically a misfire, as the timing chain stretches out skips a gear and creates the misfire. Shavings from the timing chain can also be noticed in the filter, around the drain plug or in the oil. The last sign is a rattle at idle and if this is missed serious engine damage can occur if the chain breaks. If you are experiencing any of these signs, replace your chain with this high-quality OEM (original equipment manufacturer) replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 2...(choose a part on the right to read more)
From $306.39
Make a selection 9A160410400EQ If your starter is on its way out, you will notice an intermittent clicking noise and a delay in the vehicle starting. Eventually, you will hear a metallic screeching noise that is a sure sign that your starters bendix mechanism, bearings or solenoid are kaput. When ordering a new starter, be sure to check the protection cap on the terminal for cracks which allows moisture in and causes pre-mature failure. High-quality denso OEM (original equipment manufacturer) replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 1 necessary per car.
$506.00
Make a selection A1122 The girodisc system is a direct replacement for the oe disc with the addition of girodisc provided caliper spacers. Girodisc rotor is slightly larger than the OEM rotor at 350mm versus 340mm providing greater braking force and cooling capacity. The girodisc front rotors are approx 21.0 lbs vs. 24.4 lbs for the stock units. This reduction in rotational and unsprung weight allows for quicker acceleration and suspension response. General Fitment911 2009-12
$1,620.00
Make a selection BBI9964010006 Finally, a solution that allows you to safely increase without the risk of damaging your front axles. as you add GT3 shims to your front Porsche 996/997 turbo lower control arms, you move the cv joints beyond their safe range of motion, risking failure and expensive damage. These 10mm thick precision spacers, used with 16mm of lca shims will provide an additional -1.7 deg. Of camber, while maintaining the factory cv joint and axle relationship. the spacer design features a concentric lip that positively and accurately locates it to the cv joint for perfect balance and no vibration. Each kit includes two spacers and all the needed hardware in high class 10.9 grad
$375.00
Make a selection BES91105000SST This muffler was specifically designed for a backdate to the st look. It is manufactured for mid-range and top end performance, all without drone inside the cabin. It seamlessly mates to ssi heat exchangers for added performance while keeping the cabin warm in the winter. The muffler is vastly different than the common baffle plated mufflers stuffed with packing material that are common in the aftermarket. Ours are uniquely made with double perforated sound absorption tubes based on the halbgegenstromprinzip (half counter current principle). The acoustic silencer absorption tubes are made in a trapezoidal pattern and are perforated with varying diameters, which isolate and dampen the unwanted frequencies that c...(choose a part on the right to read more)
$2,566.30
Make a selection BES96405000S1 This muffler produces a glorious flat six race car with low deep tones that reminds us of the 964 cup. It is manufactured in Germany by m&m exhaust, gmbh. This muffler is ideal for anyone who wants a lower deeper tone with more decibels, whether they are just replacing the side muffler or are running cat bypass, sport cats or a cup pipe. + 14 hp (10 kw) & + 15 tq (20 nm) gain. - 2 3/4 tubing (70mm). - weighs 13.8 lbs (6.3 kg) - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - absolutely no drone in the cabin. - does not interfere with emissions. - includes factory style hangars and new aero quip style clamps for simple installation. We recommend replacing your exhaust tip with this u...(choose a part on the right to read more)
$1,438.80
Make a selection BES98111200SHD For 2012+ 981 facts: - equal length headers with motorsports merge collector. - 200 cell hd German hjs tri metal sport cats. - t316 lightweight stainless. - primary diameter 45mm outer , 42mm inner - each header weighs 13 lbs. (6 kg) - reduces thermal stress on the motor. - made in Germany please add 2 engine to header gaskets when ordering - 2 qty 99711110731 power: - 981 (2.7l) = + 12 crank hp (9 kw) & + 11 crank torque (15 nm) - 981s (3.4l) = + 16 crank hp (12kw) & 15 crank torque ( 20 nm) our latest development for the 981 is aimed at those who are looking for more torque in the mid-range, a rich, deep exhaust growl. These headers contain the latest hjs cats, they are nicknamed "hd" for high durability ma...(choose a part on the right to read more)
$4,988.50
Make a selection BES981C1200SGT4 - equal length long tube headers with motorsports merge collector. - 200 cell hd German hjs tri metal sport cats. - primary diameter 50mm outer , 47mm inner for the larger 3.8l displacement. - t316 lightweight stainless steel. - reduces thermal stress on the motor. - made in Germany by m&m exhaust gmbh. Please add 2 engine to header gaskets when ordering - 2 qty 997 111 107 31 power: - 981 GT4 / spyder (3.8l) = + 18 crank hp (13kw) & 16 crank torque ( 21 nm) our latest development for the 981 is aimed at those who are looking for more torque in the mid-range, a rich, deep exhaust growl. These headers contain the latest hjs cats, they are nicknamed "hd" for high durability matrix design catalytic converters. T...(choose a part on the right to read more)
$5,780.50
Make a selection BES98215000S The open architecture of this muffler allows for a deeper four-cylinder turbo tone, with plenty of whistling on tap. Coming off throttle from higher rpms exudes a chorus of snarling, gurgling and crackling letting everyone know that this car is not your average 982. + 15 hp & + 12 tq gain. - 2 x 3.5 (90 mm) round tips. - thermal insulation on piping to keep suspension components cool. Withstands up to 2,012 degrees fahrenheit (1,100 degrees celsius). - lower deeper tones than the factory exhaust with far more whistling and gurgling / crackling off throttle. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - no drone in the cabin. - "aero quip" style motorsport muffler connections t...(choose a part on the right to read more)
$3,367.10
Make a selection BES98215000SK Brombacher edition valved mufflers are the perfect compromise for you and your loved ones. Rich, deep race car tones with the exhaust valve open and soft subtle, nearly stock sounds with it closed. + 17 hp & + 13 tq gain. - 2 x 3.5 (90 mm) round tips. - includes a pierburg vacuum actuated exhaust valve. - thermal insulation on piping to keep suspension components cool. Withstands up to 2,012 degrees fahrenheit (1,100 degrees celsius). - intoxicating growl at idle, partial throttle and wide open throttle with the valves open. Factory quiet with them closed! - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - "aero quip" style motorsport muffler connections to ensure a leak free exhau...(choose a part on the right to read more)
$5,309.70
Make a selection BES987C02F0S "brombacher" 987-2/s (sound version) stainless steel exhaust system
$7,420.60
Make a selection BES99101260S - + 20 crank hp & + 14 crank torque. - 200 cell hjs tri-metallic "hd" cats. - 2 tubing (50 mm) with motorsport merge collector. - weighs 18.5 lbs. (8.4 kg). - 1.5 lb (9.1 kg) saving's over OEM header. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - works with OEM sealing rings and clamps. See below for part numbers. - made in Germany. - reduces thermal load and backpressure to for more torque in the mid-range and hp on the top end. Be sure to add new clamps and sealing rings to your order. 2 qty. Clamps are needed, they are part # 99711133690 and 2 qty. Sealing rings are needed, they are part # 98011156100. Our latest development for the GT3 is aimed at those who are looking fo...(choose a part on the right to read more)
$5,286.60
Make a selection BES99102240SHDO + 15 hp & + 14 torque - 200 cell high flow, tri metal German hjs "hd" high durability matrix sports catalysts. - can be used with FVD "brombacher" mufflers. - weighs 15.5 lbs. (7.0 kg). - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - made in Germany. - intoxicating growl at idle, partial throttle and wide open throttle. The catalytic converter cores used in this system are the most advanced in the industry. They are produced by hjs in Germany and are a 200 cpsi (cell per square inch) tri-metal design. Tri-metal cats are the freest flowing and environmentally friendly aftermarket cats produced today. Tri-metal catalytic converters are rodium, platinum and iridium coated and per...(choose a part on the right to read more)
$4,383.50
Make a selection BES99105040S Perfect muffler for those looking for a more aggressive exhaust note without changing the factory catalytic converters. The added benefit is you can reuse your OEM catalytic converters for emissions purposes. + 15 hp & + 12 torque - reuses OEM cats, perfect for those concerned about warranty. - open muffler design for added power. - tubing diameter is the same as the OEM system. - weighs 19 lbs. (8,6 kg) - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - 4 on a scale of 1-10 in volume (1 being stock) below 3,000 rpms, 6 on a scale of 1-10 in volume under maximum load (3 being stock). - includes cone and v band style hardware to prevent exhaust leaks. - made in Germany. - modular desi...(choose a part on the right to read more)
$2,920.50
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |