PORSCHE 914 CHECK OUTCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 911 2009-12 - Electrical (includes uncategorized and accessory items) FVD375003 Are you experiencing vibrations in the cabin? The most likely cause is a worn transmission mount. Severely worn mounts translate to engine component wear and can even cause difficulty shifting. Our mount is manufactured in europe by an OEM supplier using the finest materials. It is a 65 shore rubber hardness value which is the same as the what was standard on these cars. Be sure to swap yours out during your next service. Sold individually. Central fitment in transmission carrier 96437502301. 1 qty. Required. Tech tip: now is the time to replace the old hardware as well. Below is a list of what is needed for installation. 1 qty. Hex head bolt m10x100 90007429202 1 qty. Lock nut m10 49020001 2 qty. Washers 10.3x...(choose a part on the right to read more)
$165.00
Make a selection FVD33150040 Replace worn-out original rear sub frame (side panel) bushings and return your car to its original ride quality with this cost effective alternative. This bushing is made in Germany. It is crafted in high carbon steel and 7075 t6 aircraft aluminum and includes a 65 shore hardness value core. This is a front and rear bushing for one sub frame. 2 are necessary per car. If you are looking for a sportier upgrade we suggest our clubsport sub frame bushing set, part # FVD33150040r. We also sell complete sub frames with the bushings installed, part # FVD331993001.
$418.00
Make a selection FVD33150045R Replace worn-out soft rubber (65 shore hardness value) control arm bushings (camber link and caster link) with sportier rubber (75 shore hardness value) that is more durable, provides more positive suspension location and is quiet and more forgiving than a monoball upgrade. This bushing cartridge is weather sealed and is crafted in high carbon steel and 7075 t6 aircraft aluminum. Sold individually.
$69.30
Make a selection FVD34101702ATK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will properly install our FVD clubsport front control arm bushings, part # FVD341999r. They are made with 85 shore rubber (like the rennsport model). Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrangements can ...(choose a part on the right to read more)
$418.00
Make a selection FVD33150010 Our weather sealed monoball cartridges are crafted in high carbon steel and 7075 t6 aircraft aluminum. They will positively locate the suspension arms so suspension motion is accurately repeated in every corner. Sold as a set. 1 kit is necessary per car. Please note: we recommend this kit for race use, as noise may resonate inside the cabin during street use. For those that are concerned about the noise, please order part # FVD3310212291
$704.00
Make a selection FVD333505001 Without ( i030 ) sport suspension set contains: - 2 x 993 333 107 01 - 2 x 996 333 105 02 also c4s cabrio with standart suspension
$166.34
Make a selection FVD332901QDF Helical lsd differential for Porsche 911 is suitable for Porsche with 901 gearboxes, to replace the standard open differential. A direct replacement for the standard Porsche differential. Automatic torque biasing differential enables your car to accelerate quicker and corner faster. The differential powers both drive wheels under nearly all conditions. With an ordinary open differential (standard on most cars), precious power is wasted during wheel spin under acceleration. This happens because the open differential shifts power to the wheel with less grip, along the path of least resistance. The differential, however, does just the opposite. It senses which wheel has better grip, and biases the power to that wh...(choose a part on the right to read more)
$2,013.00
Make a selection FVD347088CS The momo prototipo 6c is a classic wheel with a modern carbon twist, it uses the finest modern materials giving it the perfect blend of old and new. Made from top grain black leather that includes contrasting grey stitching to match the wrapped carbon cut-out spokes. The wheel also includes a momo horn button. The momo prototipo 6c is the excellent choice for those wishing to retain the character of their vehicle while refreshing the interior. Style: rally color: black material: leather spoke finish: wrapped polished carbon / cut out horn: matte black with gloss momo horn button diameter: 13.78 in (350 mm) rim diameter: 1.29 in (33 mm) dish: 1.4 inch (37 mm) weight: 2.86 lbs. (1.3 kg) please note: this kit is o...(choose a part on the right to read more)
$739.20
Make a selection FVD34101802RAK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will properly install our FVD race front control arm bushings. They are made with uniball bearings so suspension motion is accurately repeated in every corner. Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrange...(choose a part on the right to read more)
$438.90
Make a selection FVD34101807ATK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will properly install our FVD clubsport front control arm bushings, part # FVD341999r. They are made with 85 shore rubber (like the rennsport model). Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrangements can ...(choose a part on the right to read more)
$418.00
Make a selection FVD3419991 This is a cost effective alternative to buying new control arms. Replace worn-out original soft rubber (65 shore hardness value) control arm bushings with new bushings of the same rubber (65 shore hardness value). This bushing set is made in Germany, weather sealed, crafted in high carbon steel and 7075 t6 aircraft aluminum and includes a 65 shore hardness value cores. This is a front and rear bushing for the front lower control arm (wishbone). 2 sets are necessary per car.
$124.30
Make a selection FVD34391101SET Replace worn-out original front lower control arm bushings to return your car to its intended suspension geometry and steering feedback. Features: better handling reduces that sloppy steering feel does not produce any noise like the teflon bushings. Rubber has the original shore hardness value of 65 (like oem) fit's like oem, simple installation made in Germany if you are looking for a sportier upgrade we suggest our sport lower control arm set, part # FVD34391192set. Set is sold per axle. 2 necessary per car.
$152.90
Make a selection FVD34791130 Enhance steering precision and steering feedback by simply replacing your original tie rods. Turbo tie rods use a spherical inner joint instead of soft rubber bushings. They offer quicker steering response, more sensitivity and more precision. These are standard length we highly recommend them for lowered vehicles with bump steer kits like part # FVD34791100 or FVD347911930 . We also offer turbo tie rods in longer lengths for other applications, check part # FVD34791180r and FVD34791181ry this kit is manufactured in Germany by an OEM supplier, made from high carbon steel and 7075 t6 aluminum. Kit includes: 2 qty. Outer tie rods 2 qty. Inner tie rods 2 qty. Spacing washers 2 qty. Boots 2 qty. Castle nuts 2 qty. ...(choose a part on the right to read more)
$222.24
Make a selection FVD3511B18033A This line is dedicated to the most demanding customers.this braking system originates from the racing components, consisting of a ventilated, integral or composite disc, aluminium calipers, a complete set of high performance brake pads, metal braid tubes and high quality small parts. Please remember that in the European community, gran turismo products may only be used in racing and on private roads, unless you have obtained a new approval in compliance with directive 98/12/ec. Proven on-track performance; disperses gasses, cleans pads for better 'bite'; reduces 'usprung weight' for better handling; provides maximum braking force without the flex of sliding callipers; reduces heat-related stress, increases ...(choose a part on the right to read more)
$4,175.60
Make a selection FVD332997QDF Helical lsd differential for Porsche 997, to replace the standard open differential. A direct replacement for the standard Porsche differential. Automatic torque biasing differential enables your car to accelerate quicker and corner faster. The differential powers both drive wheels under nearly all conditions. With an ordinary open differential (standard on most cars), precious power is wasted during wheel spin under acceleration. This happens because the open differential shifts power to the wheel with less grip, along the path of least resistance. The differential, however, does just the opposite. It senses which wheel has better grip, and biases the power to that wheel. It does this smoothly and constantly, ...(choose a part on the right to read more)
$2,013.00
Make a selection FVD3511N19518A This line is dedicated to the most demanding customers.this braking system originates from the racing components, consisting of a ventilated, integral or composite disc, aluminium calipers, a complete set of high performance brake pads, metal braid tubes and high quality small parts. Please remember that in the European community, gran turismo products may only be used in racing and on private roads, unless you have obtained a new approval in compliance with directive 98/12/ec. Proven on-track performance; disperses gasses, cleans pads for better 'bite'; reduces 'usprung weight' for better handling; provides maximum braking force without the flex of sliding callipers; reduces heat-related stress, increases ...(choose a part on the right to read more)
$5,384.50
Make a selection FVD3511M39040AS The brembo gran turismo s (gt-s) braking system is ideal for clubsport and sprint type track events. The GT-s type iii system utilizes brembo type iii aggressive face type discs that offer high initial response with a smooth pedal feel. The type iii offers the highest overall braking confidence and control, allowing a quick qualifying time or top results in sprint races. Gt-s systems contain advanced calipers that include racing style radiators, dual inner piston seals, an inner pressure seal and an outer wiper seal. This innovative design provides the best combination of performance and long-lasting track use. The calipers are hard anodized in black (machined brembo logo in red) for resistance to corrosion and...(choose a part on the right to read more)
$5,164.50
Make a selection FVD35161143 Wheel spacers make your tires and wheels appear wider by moving the wheel out from the hub, providing both performance and appearance improvements. Whether you want improved handling, increased safety, or simply desire your car to make a statement about your individual style, wheel spacers can help you accomplish your goal. This spacer includes a hub centric design that makes the spacer act as a precise extension of the axle hub for wheel balance. It bolts to the hub by reusing the existing wheel studs, the wheel is then bolted to the spacer studs and affixed with included nuts. Size: 43 mm (1.69 inches) bolt pattern: 5/130 center bore: 71.6 bolt / stud: stud thread type: 14x1.5 material: strength tested alumin...(choose a part on the right to read more)
$187.00
Make a selection FVD3511M29016A This line is dedicated to the most demanding customers.this braking system originates from the racing components, consisting of a ventilated, integral or composite disc, aluminium calipers, a complete set of high performance brake pads, metal braid tubes and high quality small parts. Please remember that in the European community, gran turismo products may only be used in racing and on private roads, unless you have obtained a new approval in compliance with directive 98/12/ec. Proven on-track performance; disperses gasses, cleans pads for better 'bite'; reduces 'usprung weight' for better handling; provides maximum braking force without the flex of sliding callipers; reduces heat-related stress, increases ...(choose a part on the right to read more)
$5,054.50
Make a selection FVD35161107 Wheel spacers make your tires and wheels appear wider by moving the wheel out from the hub, providing both performance and appearance improvements. Whether you want improved handling, increased safety, or simply desire your car to make a statement about your individual style, wheel spacers can help you accomplish your goal. This spacer fits between the wheel and hub. Size: 7 mm (.275 inches) bolt pattern: 5/130 center bore: 71.6 bolt / stud: n/a thread type: 14x1.5 material: strength tested aluminum alloy coating: anodized for corrosion protection hub alignment set screws are included. Longer bolts sold separately depending on application. Made in Germany. Sold individually. Can be used in front and/or rear. No...(choose a part on the right to read more)
$93.97
Make a selection FVD3511N29518A This line is dedicated to the most demanding customers.this braking system originates from the racing components, consisting of a ventilated, integral or composite disc, aluminium calipers, a complete set of high performance brake pads, metal braid tubes and high quality small parts. Please remember that in the European community, gran turismo products may only be used in racing and on private roads, unless you have obtained a new approval in compliance with directive 98/12/ec. Proven on-track performance; disperses gasses, cleans pads for better 'bite'; reduces 'usprung weight' for better handling; provides maximum braking force without the flex of sliding callipers; reduces heat-related stress, increases ...(choose a part on the right to read more)
$5,384.50
Make a selection FVD3511M29007A This line is dedicated to the most demanding customers.this braking system originates from the racing components, consisting of a ventilated, integral or composite disc, aluminium calipers, a complete set of high performance brake pads, metal braid tubes and high quality small parts. Please remember that in the European community, gran turismo products may only be used in racing and on private roads, unless you have obtained a new approval in compliance with directive 98/12/ec. Proven on-track performance; disperses gasses, cleans pads for better 'bite'; reduces 'usprung weight' for better handling; provides maximum braking force without the flex of sliding callipers; reduces heat-related stress, increases ...(choose a part on the right to read more)
$5,054.50
Make a selection FVD35161157 Wheel spacers make your tires and wheels appear wider by moving the wheel out from the hub, providing both performance and appearance improvements. Whether you want improved handling, increased safety, or simply desire your car to make a statement about your individual style, wheel spacers can help you accomplish your goal. This spacer includes a hub centric design that makes the spacer act as a precise extension of the axle hub for wheel balance. It bolts to the hub by reusing the existing wheel studs, the wheel is then bolted to the spacer studs and affixed with included nuts. Size: 57 mm (2.24 inches) bolt pattern: 5/130 center bore: 71.6 bolt / stud: stud thread type: 14x1.5 material: strength tested alumin...(choose a part on the right to read more)
$220.00
Make a selection FVD35161123 Wheel spacers make your tires and wheels appear wider by moving the wheel out from the hub, providing both performance and appearance improvements. Whether you want improved handling, increased safety, or simply desire your car to make a statement about your individual style, wheel spacers can help you accomplish your goal. This spacer includes a hub centric design that makes the spacer act as a precise extension of the axle hub for wheel balance. It bolts to the hub by reusing the existing wheel studs, the wheel is then bolted to the spacer studs and affixed with included nuts. Size: 23 mm (.905 inches) bolt pattern: 5/130 center bore: 71.6 bolt / stud: stud thread type: 14x1.5 material: strength tested alumin...(choose a part on the right to read more)
$132.00
Make a selection FVD3511M19004A The brembo gran turismo (gt) braking system is ideal for use on the street and for light track use. This GT system expands upon the original drilled disc's face type made by Porsche. The cross drilled disc surface continuously refreshes the braking surface and offers the highest initial response of any disc type. So, you can confidently respond to sudden pedestrian or traffic movement with maximum braking performance. Drilled discs operate in a wide range of operating temperatures and environments and respond confidently in wet weather. The GT line is dedicated to the most demanding customers. It originates from racing components, consisting of floating ventilated cross drilled discs, aluminum calipers with op...(choose a part on the right to read more)
$5,054.50
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |